Neilsen CT0416 Instruction Manual

FOLDING ENGINE STAND 2000LBS CT0416
WARNING
FOR YOUR SAFETY AND TO PREVENT INJURY:
Do not exceed it's rated load capacity. Overloading can cause damage to or failure of the stand.
Always use stand on hard, level surface capable of sustaining the load.
Never attempt to move loaded stand across floor having cracks or other obstacles, which might
impede movement of wheels.
Visual inspection should be made before each use of the stand, checking for cracked welds,
damaged loose or missing parts.
Be sure that the load is centered and secured to the mounting plate.
Never work directly under a supported engine.
Do not drop load suddenly as resulting shock to unit may cause damage.
All mounting hardware must be tight before using. Do not substitute hardware provided.
INSPECTION
Visual inspection should be made before each use of the engine stand.
Any engine stand which appears to be damaged in any way, is found to be badly worn, or
operated abnormally must be removed from service.
If the engine stand is accidentally subjected to an abnormal load or shock tn must be inspected
by the manufacturer immediately.
It is recommended that an annual inspection of the engine stand be made and that any
defective parts, decals, or warning labels be replaced with manufacturer's specified parts.
ASSEMBLY INSTRUCTIONS
1. Attach two 3" swivel casters(#25) and one 3.5" swivel caster(#14) to the base frame(#17)
bolts(#15) and lock washers(#22).
2. Assemble legs(#20) to the base frame (#17) using ringed lock pins(#18) and R pin (#19).
3. Attach the main post(#8) to the cross member between the open channels using bolts(#13),nuts
(#4) and flat washers(#3).
4. Attach the top of supports(#12) to the main post using bolt(#9), nut(#11) and flat washer(#10),
and then connect the end of supports to base frame using bolts(#16), nuts (#11) and flat
washers(#10).
5. Insert the engine mounting plate(#5) through the tube at the top of the main post. Rotate the
plate till one of the holes in the inner tube is aligned with a hole in the outer tube and insert
the ringed pin(#7).
6. Insert the handle(#6) through the hole in the turning plate tube which protrudes from the top
off the main post.
7. Attach the shifting stands(#1) to the rotating head (#5) using bolts(#2), flat washers(#3)
and nuts(#4).
8. To fold up the legs remove the spring clips from the ring headed pins closest to the fixed wheels
and pull out the pins. Fold the legs up. Always retain the legs in the upright position by
the pins through the holes in the frame directly in front of the folded legs. Retain pins with clips.
Check all bolts for tightness before operating.
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Ref no Description QTY Ref no Description
1 Shifting stand 4 14 3.5" Swivel Caster
2 Bolt M14 x 65 4 15 Bolt M8 x 12
3 Flat washer 14 10 16 Bolt M16 x 90
4 Nut M14 6 17 Base frame
Turning plate Lock pin
5 18
1
6 Handle 19 "R" pin
1
7 20 Leg
Pin 1
Main post
8 1 21 3-1/2" caster
9 Bolt M16 x 100 1 22 Lock washer 8
10 Flat washer 16 23 Bolt M8 x 20
3
11 Nut M16 3 24 Nut M8
12 Support 25 3" Swivel Caster
2
2
13 Bolt M14 x 85
Made in China
using
QTY
1
12
2
1
4
4
2
2
20
8
8
2