Page 1
NOTE: Vax recommends that you raise the height of the brush bar when using this cleaner on lino and hard flooring. Vax cannot be held responsible for damage to these surfaces if the customer fails to take notice of this recommendation.
Page 2
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 2 All manuals and user guides at all-guides.com www.vax.co.uk 1. Diagram VZL-6011 Fig.1/1 1 Handle Grip 13 Bumper WARNING: This cleaner has 2 Handle/Extension Wand 14 Hose Guide a constantly rotating brush...
If the supply cord or plug is damaged, return the vacuum cleaner to a Vax IMPORTANT: If the inlet, hose or extension tube is Authorised Service Agent or suitably qualified blocked, switch off the vacuum cleaner and person for examination, repair or adjustment.
Slide handle through top of potentially cause some damage to the floor surface. back panel until it snaps NOTE: Vax recommends that you raise the height of into place. the brush bar when using this cleaner on lino and hard flooring.
Page 5
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 5 All manuals and user guides at all-guides.com Vax Careline 0870 606 1248 To change the dusting brush into an upholstery tool, Floor/Carpet Cleaning simply snap off the square plastice ring housing the Move the handle and adjust it to the desired position for bristles.
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 6 All manuals and user guides at all-guides.com www.vax.co.uk 5. Dirt container & filter: Remove foam filter Press tab on bottom of foam filter cover and pull to remove. removal & replacement WARNING: to reduce risk of injury from moving parts - unplug before servicing.
Page 7
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 7 All manuals and user guides at all-guides.com Vax Careline 0870 606 1248 NOTE: The filter housing also needs to be washed Replace exhaust filter regularly with cold water and dried thoroughly before Return exhaust filter to base of cleaner and snap into replacing and restarting the vacuum cleaner.
Page 8
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 8 All manuals and user guides at all-guides.com www.vax.co.uk 6. Belt or brushbar: removal To replace belt or brushbar Slide belt onto motorshaft. and replacement TOOL REQUIRED: Phillips screwdriver MOTOR SHAFT WARNING: to reduce the risk of injury from moving parts - unplug cleaner before changing belt or brush.
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 9 All manuals and user guides at all-guides.com Vax Careline 0870 606 1248 Re-attach nozzle guard by aligning the four (4) tabs in the 7. Lightbulb: removal and base slots. Rotate nozzle guard back in place (Fig. 6/7).
Vax VZL-6011 User Guide.qxd:VZL-6011 User Guide 17/9/08 11:03 Page 10 All manuals and user guides at all-guides.com www.vax.co.uk 8. General maintenance 9. Troubleshooting WARNING: TO REDUCE RISK OF PERSONAL INJURY, WARNING: to reduce risk of injury from moving UNPLUG VACUUM CLEANER BEFORE SERVICING parts - unplug before servicing.
Please make a note of the serial number and model Weight: 8.5kg number of the carpet cleaner before calling. There are over 400 approved Vax Service Agents in the UK. For the nearest Service Agent, please call the Vax Careline. Subject to technical change without notice.
Page 12
Page 12 All manuals and user guides at all-guides.com EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the VZL-6011 Mach1 Upright is manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive Waste electrical products should not be disposed of with household waste.