Summary of Contents for E-data DSL-2120 Series
- Page 1 DSL-2120/2120W Series ADSL2PLUS 1-port with USB Router User Guide Revision 1.0 Apr/2008 Proprietary & Confidential Page 1 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 2: Table Of Contents
Contents Chapter 1 - Getting to Know DSL-2120/2120W ..................6 1.1 Features of the DSL-2120/2120W..................... 6 1.2 Applications for the DSL-2120/2120W..................... 8 1.2.1 Accessing the Internet........................9 1.2.2 Making LAN to LAN Connections....................9 Chapter 2 - Introducing the Web Configurator ................... 10 2.1 Accessing the DSL-2120/2120W Web Configurator .............. - Page 3 4.3.2 Introducing DHCP ........................28 4.3.3 Enabled DHCP..........................28 4.3.4 Relay DHCP ..........................29 4.4 The Wireless LAN Screen (for DSL-2120W only) ................. 30 4.4.1 Access Point Settings ......................... 31 4.4.2 Multiple SSIDs Settings....................... 32 4.4.3 Wireless MAC Address Filter ...................... 32 4.4.3.1 WEP............................
- Page 4 6.5 Dynamic DNS ..........................61 6.5.1 DYNDNS Wildcard........................61 6.5.2 Configuring Dynamic DNS ......................61 6.6 CWMP .............................. 62 Chapter 7 - The Maintenance Screens ....................64 7.1 The Administration Screen ......................64 7.2 The Time Zone Screen........................64 7.3 The Firmware Screen........................65 7.4 The SysRestart Screen ........................
- Page 5 FCC Radiation Exposure Statement ..............86 Proprietary & Confidential Page 5 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 6: Chapter 1 - Getting To Know Dsl-2120/2120W
Chapter 1 - Getting to Know DSL-2120/2120W Your DSL-2120/2120W integrates high-speed 10/100Mbps auto-negotiating LAN interface(s), USB port and a high-speed ADSL port. The DSL-2120/2120W is perfect for making LAN-to-LAN connections to remote networks and for high-speed Internet browsing. The DSL-2120/2120W provides lightning-fast Internet access to multiple users by combining Direct Subscriber Line (DSL) and Network Address Translation (NAT). - Page 7 You must register for this service with a Dynamic DNS client. Multiple PVC (Permanent Virtual Circuit) Support Your DSL-2120/2120W supports up to 8 PVCs. ADSL Standards ♦ Compliant to ITU-T G.992.1 (G.dmt), G.992.3 (ADSL2), G.992.4, and G.992.5 (ADSL2+) Annex A, B, I, J, L, and M ♦...
-
Page 8: Applications For The Dsl-2120/2120W
♦ PPPoE feature PPPoE idle time out PPPoE dial on demand Networking Compatibility The DSL-2120/2120W is compatible with major ADSL Digital Subscriber Line Access Multiplexer (DSLAM) providers. Multiplexing The DSL-2120/2120W supports VC-based and LLC-based multiplexing. Encapsulation The DSL-2120/2120W supports PPP over ATM Adaptation Layer 5 (PPPoA, RFC 2364), RFC 1483 encapsulation over ATM, MAC encapsulated routing (ENET Encapsulation) as well as PPP over Ethernet (RFC 2516). -
Page 9: Accessing The Internet
1.2.1 Accessing the Internet The DSL-2120/2120W is an ideal high-speed Internet access solution. It supports the TCP/IP protocol, which the Internet uses exclusively. The DSL-2120/2120W is compatible with all major ADSL DSLAM providers. A DSLAM is a group of ADSL line cards with data multiplexed into a network interface/connection, such as T1, OC3, DS3, ATM or Frame Relay. -
Page 10: Chapter 2 - Introducing The Web Configurator
Chapter 2 - Introducing the Web Configurator Your DSL-2120/2120W can be managed from anywhere with the embedded Web configurator using a Web browser, such as Microsoft Internet Explorer or Netscape Navigator. Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled should be used. -
Page 11: Resetting The Dsl-2120/2120W
firmware and to run diagnostic tests on the DSL-2120/2120W. Click on Status to see DSL-2120/2120W device information, system logs and performance statistics. Click on Help to see available help topics. 2.3 Resetting the DSL-2120/2120W If you should forget your password, or if you can’t gain access to the DSL-2120/2120W, you will have to reload the factory-default configuration file or use the RESET button on the back of the DSL-2120/2120W device to regain access. -
Page 12: Chapter 3 - The Quick Start Wizard
Chapter 3 - The Quick Start Wizard Use the Quick Start wizard to configure your system settings. Your ISP may have configured some of the fields in the wizard for you. Click on the RUN WIZARD button to start the Quick Start wizard. The Quick Start wizard will open a new browser window with the following screen. -
Page 13: Choosing The Time Zone
The following table describes the labels in this screen. LABEL DESCRIPTION New Password Enter the password you wish to use here Confirmed Password Enter the password again to confirm Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard without saving. -
Page 14: Setting The Isp Connection Type
3.3 Setting the ISP Connection Type This screen helps you select, then configure, your ISP connection type. Select the Internet connection type you use to connect to your ISP. Click on BACK to return to the previous screen, on NEXT to continue, or on EXIT to exit the wizard. The following screen will vary depending on which connection type you chose. -
Page 15: Configuring Static Ip Address
The following table describes the labels in this screen. LABEL DESCRIPTION Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here. VCI can range from 1 to 65535. Connection Type Select your connection type from the dropdown list. Your ISP should provide the above information. -
Page 16: Configuring Pppoe
The following table describes the labels in this screen. LABEL DESCRIPTION Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here. VCI can range from 1 to 65535. IP Address Enter the IP address here. Subnet Mask Enter the Subnet Mask here. -
Page 17: Configuring Pppoa
The following table describes the labels in this screen. LABEL DESCRIPTION Username Enter your username here. Password Enter your password here. Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here. VCI can range from 1 to 65535. Connection Type Select your connection type from the dropdown list. -
Page 18: Configuring Bridge Mode
The following table describes the labels in this screen. LABEL DESCRIPTION Username Enter your username here. Password Enter your password here. Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here. VCI can range from 1 to 65535. Connection Type Select your connection type from the dropdown list. -
Page 19: Multiplexing
The following table describes the labels in this screen. LABEL DESCRIPTION Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here. VCI can range from 32 to 65535. Connection Type Select your connection type from the dropdown list. Your ISP should provide the above information. -
Page 20: Vpi And Vci
processing overhead, this method may be advantageous if it is not practical to have a separate VC for each carried protocol; for example, if charging heavily depends on the number of simultaneous VCs. 3.3.7 VPI and VCI Be sure to use the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers assigned to you. -
Page 21: Chapter 4 - The Interface Setup Screens
Chapter 4 - The Interface Setup Screens The Interface Setup screens help you connect your DSL-2120/2120W to the Internet and to your local network. 4.1 Interface Setup Overview The physical connections determine whether the DSL-2120/2120W ports are local area network (LAN) ports or wide area network (WAN) ports. There are two kinds of IP networks. The local, private kind is the LAN network;... -
Page 22: Atm Vc & Qos
4.2.1 ATM VC & QoS Asynchronous transfer mode (ATM) is a protocol that arranges data into small, uniform-sized cells with VCI data, as opposed to variable-sized data packets. ATM settings are used to connect to your ISP. Your ISP provides your VPI and VCI setting information. You can configure up to 8 virtual circuits (VC), each using different encapsulations, if you apply for 8 different VCs from your ISP. -
Page 23: Encapsulation
Sustained Cell Rate (SCR) is the mean cell rate of a bursty, on-off traffic source that can be sent at the peak rate, and a parameter for burst-type traffic. SCR may not be greater than the PCR; the system default is 0 cells/sec. Maximum Burst Size (MBS) is the maximum number of cells that can be sent at the PCR. -
Page 24: Dynamic Ip Address
4.2.2.1 Dynamic IP Address The following table describes the labels in this screen. LABEL DESCRIPTION Encapsulation Select your encapsulation type from the dropdown list. Bridge interface Select whether Bridge interface is activated or deactivated. Select whether NAT is Enabled or Disabled. Default Route Select whether this PVC will be the default route for Internet data. -
Page 25: Pppoe/Pppoa
Encapsulation Select your encapsulation type from the dropdown list. Static IP Address Enter the static IP Address here. IP Subnet Mask Enter the IP Subnet Mask here. Gateway Enter the Gateway address here. Select whether NAT is Enabled or Disabled. Default Route Select whether this PVC will be the default route for Internet data. -
Page 26: Bridge Mode
Encapsulation Select your encapsulation type from the dropdown list. Bridge interface Select whether Bridge interface is activated or deactivated. Connection Select whether your connection is always on or if it connects on demand. If on demand, specify how many minutes the connection may be idle before it disconnects. -
Page 27: Router Local Ip
4.3.1 Router Local IP The following table describes the labels in this screen. LABEL DESCRIPTION IP Address Enter the IP address you wish to use with your LAN here. IP Subnet Mask Enter the IP subnet mask you wish to use with your LAN here. Dynamic Route Select the Routing Information Protocol (RIP) you wish to use from the dropdown list and the direction you want from the dropdown list. -
Page 28: Introducing Dhcp
Only” means the DSL-2120/2120W will only send RIP packets, not accept any RIP packets received. Selecting “None” means the DSL-2120/2120W will not send any RIP packets nor will it accept any RIP packets received. The Dynamic Route field controls the format and the broadcasting method of RIP packets that the DSL-2120/2120W sends. -
Page 29: Relay Dhcp
The following table describes the labels in this screen. LABEL DESCRIPTION Starting IP Address Enter the starting IP address you wish to use as the DHCP server's IP assignment. IP Pool Count Enter the maximum user pool size you wish to allow. Lease Time Enter the amount of time you wish to lease out a given IP address. -
Page 30: The Wireless Lan Screen (For Dsl-2120W Only)
A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the IP addresses. If the DHCP Relay option is enabled, DHCP requests from local PCs will be forwarded to the DHCP server that runs on WAN side. -
Page 31: Access Point Settings
4.4.1 Access Point Settings The following table describes the labels in this screen. LABEL DESCRIPTION Access Point Default setting is set to Activated. If you do not have any wireless, both 802.11g and 802.11b, device in your network, select Deactived. Channel The range of radio frequencies used by IEEE 802.11b/g wireless devices is called a channel. -
Page 32: Multiple Ssids Settings
4.4.2 Multiple SSIDs Settings The following table describes the labels in this screen. LABEL DESCRIPTION SSID Index, SSID The SSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default name to a unique ID name to the AP which is already built-in to the router’s wireless interface. -
Page 33: Wep
LABEL DESCRIPTION Active Select Actived to enable MAC address filtering. Action Define the filter action for the list of MAC addresses in the MAC address filter table. Select Deny Association to block access to the router, MAC addresses not listed will be allowed to access the router. Select Allow Association to permit access to the router, MAC addresses not listed will be denied access to the router. - Page 34 incorporates Message Integrity Code (MIC) to provide protection against hackers. Pre-Shared key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. Proprietary & Confidential Page 34 of 86 Revision: V1.0 Apr.
-
Page 35: Chapter 5 - The Advanced Setup Screens
Chapter 5 - The Advanced Setup Screens The advanced setup screens help you manage how data enters and exits your DSL-2120/2120W. 5.1 The Routing Screen Routing directs your DSL-2120/2120W to forward data to specific IP addresses. This screen shows the routing rules you have already set. A few defaults have been configured for you. -
Page 36: The Nat Screen
routed by this rule. The IP subnet mask is the subnet mask for the final destination. A gateway does the actual forwarding of the packets. Enter the gateway’s IP address in the field or select which PVC you wish to act as a gateway. The metric is a rough estimate of the “cost”... -
Page 37: What Nat Does
5.2.1.1 What NAT Does NAT changes the source IP address in a packet received from a subscriber (the inside local address) to another (the inside global address) before forwarding the packet to the WAN side. When the response comes back, NAT translates the destination address (the inside global address) back to the inside local address before forwarding it to the original inside host. -
Page 38: Nat Application
outgoing packets, the ILA is the source address on the LAN, and the IGA is the source address on the WAN. For incoming packets, the ILA is the destination address on the LAN, and the IGA is the destination address on the WAN. NAT maps private (local) IP addresses to globally unique ones required for communication with hosts on other networks. -
Page 39: Nat Mapping Types
5.2.1.4 NAT Mapping Types NAT supports five types of IP/port mapping. They are: 1. One-to-One: In One-to-One mode, the DSL-2120/2120W maps one local IP address to one global IP address. 2. Many-to-One: In Many-to-One mode, the DSL-2120/2120W maps multiple local IP addresses to one global IP address. -
Page 40: Dmz
ILA3 IGA1 ILA4 IGA2 … Many-to-Many No Overload ILA1 IGA1 ILA2 IGA2 ILA3 IGA3 … Server Server 1 IP IGA1 Server 2 IP IGA1 Server 3 IP IGA1 5.2.2 DMZ A demilitarized zone (DMZ) is a host between a private local network and the outside public network. -
Page 41: The Qos Screen
The following table describes the labels in this screen. LABEL DESCRIPTION Rule Index Select which rule index to use with this virtual circuit. All VCs with the same IP will use the same rules. Application Select the Application you wish to support like: FTP, H.323…etc Protocol Select the protocol you wish to support: TCP, UDP or BOTH Start Port Number... -
Page 42: Rule
special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based on priority. This is useful when there are certain types of data you want to give higher priority to, such as voice data packets given higher priority than Web data packets. The main goal of QoS is prioritizing incoming data, preventing data loss due to factors such as jitter, delay and dropping. - Page 43 setting conditions here, then this packet will be remarked as the priority queue of each rule. The non-selected setting part will be treated as “don’t care” and the system will not handle this setting part. If the original packet does not have 802.1q tagged header, system will not add header for this packet even the detail setting condition has adding 802.1p priority ability.
-
Page 44: Action
Source Port Range Set the port range value that you want to filter in source side Protocol ID Set the protocol ID type that you want to filter Vlan ID Range Set the Vlan value that you want to filter IPP/DS Field Select IP QoS format IP Precedence Range... -
Page 45: The Adsl Screen
5.4 The ADSL Screen The following table describes the labels in this screen. LABEL DESCRIPTION ADSL Mode Select which mode your ADSL connection uses from the dropdown list. ADSL Type Select the ADSL type you use from the dropdown list. When you are done making changes, click on SAVE to save your changes. -
Page 46: Chapter 6 - The Access Management Screens
Chapter 6 - The Access Management Screens The access management screens help you manage what can access your network. 6.1 The ACL Screen Access Control Listing (ACL) is a management tool that acts as a filter for incoming or outgoing packets, based on application. The following table describes the labels in this screen. -
Page 47: The Filter Screen
6.2 The Filter Screen Filter is a more complex filtering tool. Three filter types are available in DSL-2120/2120W: IP/MAC filter, Application Filter, and URL Filter. 6.2.1 Assigning IP/MAC Filter Each of the indices can hold six rules, and each interface can have four associated indices, allowing 24 rules per interface. - Page 48 LABEL DESCRIPTION IP/MAC Filter Set Select the IP/MAC Filter Set you wish to modify. Index Interface Select the Interface you wish to modify. PVC0-PVC7 are WAN interfaces Direction Select which direction of data flow you wish to apply the filters to. Note that Incoming and Outgoing are from the point of view of your router, relative to the interface you select.
-
Page 49: Assigning Application Filter
6.2.2 Assigning Application Filter The following table describes the labels in this screen. LABEL DESCRIPTION Application Filter Select Application Filter is activated or deactivated. Select allow or deny ICQ traffic. Select allow or deny MSN traffic. YMSG Select allow or deny Yahoo Messenger traffic. Real Audi/Video Select allow or deny Real Audio/Video traffic. -
Page 50: Assigning Url Filter
6.2.3 Assigning URL Filter The following table describes the labels in this screen. LABEL DESCRIPTION Active Toggle the rule on or off with Yes or No, respectively. URL Index Select the URL Rule Index you wish to modify . Enter the URL you wish to deny access to your system . When you are done making changes, click on SAVE to save your changes, DELETE to delete the rule with the parameters you set or CANCEL to exit without saving. -
Page 51: The Upnp Screen
The following table describes the labels in this screen. LABEL DESCRIPTION Get Community Enter the password for incoming Get- and GetNext requests from the management station. Set Community Enter the password for incoming Set requests from the management station. The default password is ‘public’. When you are done making changes, click on SAVE to save your changes. -
Page 52: Cautions With Upnp
UPnP. 6.4.1.2 Cautions with UPnP The automated nature of NAT traversal applications in establishing their own services may present network security issues. Network information and configuration may be obtained and modified by users in some network environments. All UPnP-enabled devices may communicate freely with each other without additional configuration. -
Page 53: Installing Upnp In Windows Me
6.4.2.1 Installing UPnP in Windows Me Follow the steps below to install the UPnP in Windows Me. Step 1. Click on Start and then on Control Panel. Double-click Add/Remove Programs. Step 2. Click on the Windows Setup tab and select Communication in the Components selection box. -
Page 54: Installing Upnp In Windows Xp
6.4.2.2 Installing UPnP in Windows XP Follow the steps below to install the UPnP in Windows XP. Step 1. Click on Start and then on Control Panel. Step 2. Double-click on Network Connections. Step 3. In the Network Connections window, click on Advanced in the main menu and select Optional Networking Components... - Page 55 Step 6. Click on OK to go back to the Windows Optional Networking Component Wizard window and click on Next. Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP. You must already have UPnP installed in Windows XP and UPnP activated on the DSL-2120/2120W.
- Page 56 Step 3. In the Internet Connection Properties window, click on Settings to see the port mappings there were automatically created. Proprietary & Confidential Page 56 of 86 Revision: V1.0 Apr. 23, 2008...
- Page 57 Step 4. You may edit or delete the port mappings or click on Add to manually add port mappings. Step 5. Check the ‘Show icon in notification area when connected’ box and click on OK. An icon displays in the system tray. Proprietary &...
- Page 58 Step 6. Double-click on the icon to display your current Internet connection status. Proprietary & Confidential Page 58 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 59: Web Configurator Easy Access
6.4.2.3 Web Configurator Easy Access With UPnP, you can access the Web-based configurator on the DSL-2120/2120W without knowing the IP address of the DSL-2120/2120W. Follow the steps below to access the Web configurator. Step 1. Click Start and then Control Panel. Step 2. - Page 60 Step 4. An icon with the description for each UPnP-enabled device displays under Local Network. Step 5. Right-click on the icon for your DSL-2120/2120W and select Invoke. The Web configurator login screen displays. Proprietary & Confidential Page 60 of 86 Revision: V1.0 Apr.
-
Page 61: Dynamic Dns
Step 6. Right-click on the icon for your DSL-2120/2120W and select Properties. A properties window displays with basic information about the DSL-2120/2120W. 6.5 Dynamic DNS Dynamic DNS (DDNS) allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you through various applications. -
Page 62: Cwmp
Active Dynamic DNS can be toggled Activated or Deactivated. Service Provider Select the name of your Dynamic DNS service provider. My Host Name Enter the domain name assigned to your DSL-2120/2120W by your Dynamic DNS provider here. E-mail Address Enter your e-mail address here. Username Enter your user name here. - Page 63 Port Port used for Connection Request. User Name Enter the username used to authenticate an ACS making a Connection Request to the CPE. Password Enter the password used to authenticate an ACS making a Connection Request to the CPE. Periodic Inform Whether or not the CPE must periodically send CPE information to ACS using the inform method call.
-
Page 64: Chapter 7 - The Maintenance Screens
Chapter 7 - The Maintenance Screens The maintenance screens help you manage your DSL-2120/2120W. 7.1 The Administration Screen Use the Administration screen to change your password. If you used the Quick Start wizard, you have already changed your password once. The following table describes the labels in this screen. -
Page 65: The Firmware Screen
Daylight Saving Daylight saving can be toggled Enabled or Disabled. NTP Server Address Enter the NTP server address you wish to use here. A Network Time Protocol (NTP) server can automatically set the DSL-2120/2120W’s time for you. If you use an NTP server, you will only need to select your time zone. If you manually set the time, you can enable Daylight Saving. -
Page 66: The Sysrestart Screen
7.4 The SysRestart Screen The SysRestart screen allows you to restart your DSL-2120/2120W with either its current settings still in place or the factory default settings. The following table describes the labels in this screen. LABEL DESCRIPTION System Restart with Select which settings you wish to use once the DSL-2120/2120W has finished restarting. -
Page 67: Chapter 8 - The Status Screen
Chapter 8 - The Status Screen status screens give information about various aspects your DSL-2120/2120W’s settings. 8.1 The Device Info Screen The Device Info screen gives you information about your DSL-2120/2120W’s Internet-related settings. 8.1.1 Device Information The Device Information section tells you the current firmware your DSL-2120/2120W is using and what MAC address it is using. -
Page 68: Adsl
8.1.4 ADSL The ADSL section tells you what ADSL firmware your DSL-2120/2120W is using, the line state, the modulation type and annex mode as well as the SNR margin, line attenuation and data rate. 8.2 The System Log Screen The system log screen displays a log of the DSL-2120/2120W’s functioning. Click on CLEAR LOG to clear the log or on SAVE LOG, which will save the log data to a separate file. -
Page 69: The Statistics Screen
8.3 The Statistics Screen The statistics screen gives you information on how much data your DSL-2120/2120W has processed. Choose Ethernet or ADSL to view the respective statistics screens. 8.3.1 Ethernet The Ethernet screen gives you information on how much data your DSL-2120/2120W has transmitted and received across the Ethernet connection. -
Page 70: Adsl
8.3.2 ADSL The ADSL screen gives you information about how much data your DSL-2120/2120W has transmitted or received across the ADSL connection. Click on REFRESH to update the screen. Proprietary & Confidential Page 70 of 86 Revision: V1.0 Apr. 23, 2008... -
Page 71: Appendix A - Troubleshooting
Appendix A - Troubleshooting This chapter covers potential problems and the corresponding remedies. A.1 Using LEDs to Diagnose Problems The Light-Emitting Diodes (LED) are useful aides for finding the possible causes of problems. A.1.1 Problem: POWER LED Doesn’t Light Up The Power (PWR) LED on the front panel does not light up. -
Page 72: Problem: Can't Access Through Telnet
STEPS CORRECTIVE ACTION Check the telephone wire and connections between the DSL-2120/2120W DSL port and the wall jack. Make sure that the telephone company has checked your phone line and set it up for DSL service. Reset your ADSL line to reinitialize your link to the DSLAM. If the problem persists, contact your local distributor for assistance. -
Page 73: Problem: Forgotten Login Username And Password
Your computer’s and the DSL-2120/2120W’s IP addresses must be on the same subnet for LAN access. If you changed the DSL-2120/2120W’s LAN IP address, enter the new one as the URL. Remove any filters in LAN or WAN that block Web service. See also Section A.4. -
Page 74: Problem: Can't Access Wan Interface
connected to a computer or hub. If the 10M/100M LEDs on the front panel are both off, refer to Section A.1.2. Make sure that the IP address and the subnet mask of the DSL-2120/2120W and your computer(s) are on the same subnet. A.6 Problem: Can’t Access WAN Interface Initialization of the ADSL connection failed. -
Page 75: Problem: Can't Access Remote Management
Internet connection disconnects. STEPS CORRECTIVE ACTION Check the schedule rules. If you use PPPoA or PPPoE encapsulation, check the idle time-out setting. Contact your ISP. A.9 Problem: Can’t Access Remote Management I cannot remotely manage the DSL-2120/2120W from the LAN or WAN. STEPS CORRECTIVE ACTION Refer to the Remote Management Limitations section in the Firmware and Configuration... -
Page 76: Appendix B - Usb Driver Installation
Appendix B – USB Driver Installation B.1 Windows2K/XP Please insert the driver CD supplied. Then Click Start / Run on desktop and use Browse to open the file of E:\USB\SetupXP2K-En-De-Fr.exe (E is the letter of CD-ROM drive) then Click OK. Select the language for the installation from the choices below then click Next. - Page 77 Select Typical type then click Next. Click Next to continue. Proprietary & Confidential Page 77 of 86 Revision: V1.0 Apr. 23, 2008...
- Page 78 Now you can plug your device then click Yes. Click Continue Anyway to continue. Click Finish to end of this procedure. Proprietary & Confidential Page 78 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 79: Vista32
B.2 Vista32 Please insert the driver CD supplied. Then Click Start / Run on desktop and use Browse to open the file of E:\USB\ tcusbdrv.exe (E is the letter of CD-ROM drive) then Click OK. Select the language for the installation from the choices below then click Next. Proprietary &... - Page 80 Click Next to continue. Select Typical type then click Next. Proprietary & Confidential Page 80 of 86 Revision: V1.0 Apr. 23, 2008...
- Page 81 Click Next to continue. Now you can plug your device then click Yes. Proprietary & Confidential Page 81 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 82: Vista64
Click Continue Anyway to continue. Click Finish to end of this procedure. B.3 Vista64 Please insert the driver CD supplied. Then Click Start / Run on desktop and use Browse to open the file of E:\DSR-TC11\Driver\Vista64\setup.exe (E is the letter of CD-ROM drive) then Click OK. - Page 83 Click Next. Select I accept the terms in the license agreement then click Next to continue. Enter the User Name and Organization then click Next. Proprietary & Confidential Page 83 of 86 Revision: V1.0 Apr. 23, 2008...
- Page 84 Select Complete then click Next to continue. Click Install. Proprietary & Confidential Page 84 of 86 Revision: V1.0 Apr. 23, 2008...
- Page 85 Now you can plug your device then click Yes. Click Finish to end of this procedure. Proprietary & Confidential Page 85 of 86 Revision: V1.0 Apr. 23, 2008...
-
Page 86: Federal Communication Commission Interference Statement
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.