Operation; Maintenance; Optional Accessories - Makita 6952 Instruction Manual

Procedure 2
In addition to the procedure (1) above, insert the bit-piece
into the sleeve with its pointed end facing in.
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly. (Fig. 5)
NOTE:
• If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
bit according to the instructions above.
• When it is difficult to insert the bit, pull the sleeve and
insert it into the sleeve as for as it will go.
• After inserting the bit, make sure that it is firmly
secured. If it comes out, do not use it.
Hook
The hook is convenient for temporarily hanging the tool.
This can be removed without using a tool. This can be
installed on either side of the tool.
Installing and removing hook (Fig. 6)
Expand the upper part of the hook in both directions and
remove it. To install the hook, follow the removal
procedure in reverse.

OPERATION

Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw. Start the tool
slowly and then increase the speed gradually. Release the
switch trigger just as the screw bottoms out.
The proper fastening torque differs depending upon the
kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. Refer to the figure for the
relation between fastening time and wood screw size.
(Material to be fastened: Lauan)
(S)
12
10
8
6
4
2
0
4.2 5.0 4.9
X65 X90 X125
Screw size
004356
NOTE:
• Use the proper bit for the head of the screw/bolt that
you wish to use.
• When fastening tool screws in a steel plate, the proper
fastening torque can be obtained in an extremely short
time (approx. 0.1 - 0.2 seconds). Turn the tool off as
soon as the impact sound is heard.
6
5.7
X150
mm
• Hold the tool pointed straight at the screw or the screw
and/or bit may be damaged.
• When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
The pilot holes should be slightly smaller than the wood
screws in diameter.
• The size of wood screw which can be fastened with this
tool may differ depending upon the type of material to
be fastened. Always perform a test operation to
determine the size of wood screw.
• When fastening bolts or nuts, always perform a test
operation to verify the adequate fastening time for your
bolt or nut. Excessive fastening torque may damage
the bolt/nut or socket bit.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes. (Fig. 7)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After replacing brushes, plug in the tool and break in
brushes by running tool with no load for about 10 minutes.
Then check the tool while running and electric brake
operation when releasing the switch trigger. If electric
brake is not working well, ask your local Makita service
center for repair. (Fig. 8)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Screw bits
• Bit piece
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.