Tuner - Philips FW-C80 Manual

All manuals and user guides at all-guides.com

TUNER

MINI HIFI SYSTEM
STANDBY
ON
POWER SAVE
IR SENSOR
CD 1•2•3 BAND
C1 • 2 • 3 BAND
CD TUNER
SEARCH•TUNING STOP•CLEAR
CLOCK/
PROG DIM
TIMER
BASS
wOOx
PLUS
TECHNOLOGY
Note:
– For 'EASY SET' feature, please refer to
page 11.
Tuning to radio stations
1 Press TUNER (BAND) to select TUNER
mode.
™ "TUNER" will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2 Press TUNER (BAND) again to select
the desired waveband : FM, MW or LW.
3 Press à or á for more than one
second, then release.
™ The display will show "SEARCH"
until a radio station with sufficient
signal strength is found.
16
pg 01-26/C80/22-Eng 16
NEWS/TA
RDS
TAPE 1•2 CDR/DVD
TAPE CDR AUX
PRESET
PLAY PAUSE PREV SIDE NEXT
DUB
A. REV RECORD
(HSD)
TREBLE
LEVEL
Notes:
• Repeat this procedure until the desired
– You can cancel the automatic
station is reached.
• To tune to a weak station, briefly press
à or á repeatedly until the display
– If you want to reserve a section of
shows the desired frequency and/or
when the best reception has been
obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
Manual programming
memory. When a preset radio station is
1 Press TUNER (BAND).
selected, the preset number appears next
2 Press TUNER (BAND) again to select
to the frequency on the display.
3 Press PROG for less than one second.
Automatic programming
1 Press TUNER (BAND).
2 Press PROG for more than one second.
™ The
starts flashing and
PROGRAM
"AUTO" will be displayed.
4 Press à or á to tune to the desired
™ The system will start searching for all
radio stations with RDS and then frequency.
followed by radio stations on FM, • If you wish to store the radio station to
another preset number, press 4 or 3 to
MW and LW band respectively.
™ All available stations will be stored
select the desired preset number.
automatically. The frequency and 5 Press PROG again.
preset number will be displayed ™ The
briefly. radio station will be stored.
™ The system will stop searching when
• Repeat steps 3 – 5 to store other preset
all the available radio stations are
radio stations.
stored or when the memory for 40
Notes:
preset radio stations is used.
– When 40 radio stations are stored and
™ The system will remain tuned to the
you attempt to store another radio
last stored preset radio station.
station, the display will show
" PROGRAM FULL ". If you want to
change an existing preset number,
programming by pressing PROG or Ç
repeat steps 3 – 5.
(on the system only).
– You can cancel manual programming by
pressing Ç (on the system only).
preset numbers, for example preset
– During programming, if no button is
numbers 1 to 9, select preset 10 before
pressed within 20 seconds, the system
starting automatic programming, only
will exit program mode automatically.
the preset numbers 10 to 40 will be
programmed.
Tuning to Preset Radio
Stations
• Press 4 or 3 to select the desired
preset number.
the desired waveband : FM, MW or LW.
™ The preset number, radio frequency,
and waveband appear on the display.
™ The starts flashing.
PROGRAM
™ The next available preset number will
be displayed for selection.
3/6/00, 2:23 PM
disappears and the
PROGRAM
3139 116 19681