Extreme Networks QXO-AP3825E User Manual
  1. Manuals
  2. Brands
  3. Extreme Networks Manuals
  4. PCI Card
  5. QXO-AP3825E
  6. User manual
Extreme Networks QXO-AP3825E User Manual

Extreme Networks QXO-AP3825E User Manual

802.11 a/n/ac module
Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual
802.11 a/n/ac Module
QXO-AP3825E
User's Manual
-
1 -

Advertisement

Table of Contents
loading

Summary of Contents for Extreme Networks QXO-AP3825E

  • Page 1 802.11 a/n/ac Module QXO-AP3825E User’s Manual...

  • Page 2: Product Description

    PRODUCT DESCRIPTION QXO-AP3825E is a 5G dual band concurrent 3T3R PCIe module base on QCA9890 solution. PRODUCT SPECIFICATION RF Specification Support 5GHz Radio 1 64-bit PCI-E Interface 3.3V Operating Voltage I-PEX Antenna Connectors 802.11a/n/ac Frequency Band 5.190~5.795GHz Data rate 1300Mbps ≤...
  • Page 3 List of certificated antennas Type Model Connector 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz U.FL PIFA PIFA ANT-PIFA7262AG U.FL Dipole WS-ANT-5DIP-3 RPSMA RPSMA Panel WS-AI-DX07025 RPSMA Panel WS-AI-DX10055 Omni WS-AI-DX02360 RPSMA Sector WS-AI-DT05120 RPSMA Note: The EUT has three antennas. (3TX/3RX) Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.

  • Page 4: Federal Communication Commission Interference Statement

    Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 5 This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required.

  • Page 6: End Product Labeling

    This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: QXO-AP3825E”.

  • Page 7: Manual Information To The End User

    Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

  • Page 8: Industry Canada Statement

    Industry Canada statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 9 Avertissement: (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à...

  • Page 10: Note Importante

    This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.

  • Page 11: Manuel D'information À L'utilisateur Final

    Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 4141B-AP3825E".
  • Page 12 This radio transmitter (IC: 4141B-AP3825E) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

  • Page 13: Professional Installation Instruction

    Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2.

Table of Contents