Page 1
User’s Guide L226WU ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. ee the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Page 3
Important Precaautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base Place the monitor with its front facing downward on a cushion or soft cloth. Rotate the Stand Body as shown in figure Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat surface. Pushing Latch inside, Take the stand base from stand body. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -3˚~17˚...
Connecting the Display Using the Computer Make sure to turn off the computer and product. Connect signal input cable screw of the signal cable. Connect DVI Cable Connect D-sub Cable Connect USB Cable Power Cord Wall-outlet type PC-outlet type DVI-D(This feature is not available in all countries.) Press button on the front switch panel to turn the power on.
Use USB programs Connecting the USB(Universal Serial Bus) Cable Plug in the USB cable as in the diagram. AC-IN D-SUB DVI-D Tidying USB (Universal Serial Bus) Cable Elevate the monitor as far as possible follow the arrow to rotate, and plug the USB cable into the monitor.
Page 9
If your computer fails to meet the system requirements, the warning message "DisplayLink Core Software" will be displayed. Press the [OK] button, and continue to install "LG USB Easy Connection" program. Install "LG USB Easy Connection" program as the instruction message says, fully remove the USB cable, and then reboot your computer.
Page 10
Use USB programs When the installation of "LG USB Easy Connection" program is completed, icons as shown in the picture will be created in the taskbar. With these icons, you can easily use features such as Screen Resolution, Color Quality, Screen Rotation, Extend To, Extend and Mirror.
Page 11
Monitor and USB Display connectors support USB 2.0 High Speed. Does not support DOS game (StarCraft) and other 3D games. For more information on USB, visit the following web site.(http://www.usb.org) ‘LG USB Easy Connection’ program may be changed without notice for the purpose of product improvement. Left Right...
Control Panel Functions Front Panel Controls You can select the computer that you want to use by SOURCE Button selecting input signal (DVI, D-Sub or USB). The default input signal is analogue (D-Sub). Use this button to enter or exit the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control...
Page 13
Control Panel Functions Buttons AUTO/SET Button Power Button Power Indicator Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A19. Use this button to enter a selection in the On Screen Display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
Page 15
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu BRIGHTNESS PICTURE CONTRAST GAMMA COLOR PRESET GREEN BLUE HORIZONTAL POSITION VERTICAL CLOCK PHASE TRACKING SHARPNESS LANGUAGE SETUP POSITION VERTICAL WHITE BALANCE POWER INDICATOR...
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
Page 17
On Screen Display(OSD) Selection and Adjustment Main menu PICTURE P I C T U R E MENU : Exit : Decrease : Increase : Select another sub-menu COLOR C O L O R MENU : Exit : Decrease : Increase : Select another sub-menu Sub menu...
Page 18
On Screen Display(OSD) Selection and Adjustment Main menu POSITION P O S I T I O N MENU : Exit : Decrease : Increase : Select another sub-menu TRACKING T R A C K I N G MENU : Exit : Decrease : Increase : Select another sub-menu...
Page 19
On Screen Display(OSD) Selection and Adjustment Main menu SETUP S E T U P S E T U P MENU : Exit : Adjust : Adjust : Select another sub-menu If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again.
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen.
Troubleshooting Check the following before calling for service. No image appears No image appears ● Is the power cord of the display connected? ● Is the power on and the power indicator blue or green? ● Is the power indicator amber? ●...
Troubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found"...
Specifications Display 22 inches (55.868 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 22 inches viewable 0.282*0.282 mm pixel pitch Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play DDC 2B Power On Mode Sleep Mode Consumption...
Page 25
Specifications Stand Base Attached ( Power cord Wall-outlet type or PC-outlet type Standard Data Rate Power Consumption Max 2.5W x 2 NOTE Information in this document is subject to change without notice. ), Detached ( O ) USB 2.0, Self-Power Max 480 Mbps...
Specifications Preset Modes (Resolution) Analog,Digital supporting modes Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1680 x 1050 USB supporting mode...
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth. Separate the stand using a screwdriver as shown in the picture. Install the Wall mount plate.