Related Manuals for LG E2341T
Summary of Contents for LG E2341T
-
Page 1: Lcd Monitor
OWNER’S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODEL E1941T E1941S E2041T E2041S E2241T E2241S E2341T E2441T www.lg.com... -
Page 2: Important Precautions
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. - Page 3 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
-
Page 4: On Cleaning
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. - Page 5 If any items are missing, contact your dealer. User's Guide/Cards DVI-D Signal Cable (Only E1941T/E2041T/E2241T/ E2341T /E2441T) (This feature is not available in all NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product.
-
Page 6: Connecting The Display
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (A type) Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture. -
Page 7: Disassembling The Stand
Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat surface. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture Place the monitor face Down on the cushion or soft cloth. Use a coin on the back of the Stand Base and turn the screw anticlock- wise to loosen... - Page 8 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (B type) Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture.
- Page 9 Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat surface. Nip Latch inside,Take off the stand base from stand body. Place the monitor face Down on the cushion or soft cloth.
- Page 10 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (C type) Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Body into the product in the correct direction as shown in the picture.
- Page 11 Connecting the Display Disassembling the stand Put a cushion or soft cloth on aflat surface. To disconnect the Stand Base from the Stand Body,simply unfold the screw handle and turn"counter-clockwise" to loosen the screw and disconnect the Stand Base from its body. Place the monitor face Down on the cushion or soft cloth.
-
Page 12: Positioning Your Display
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚... -
Page 13: Connecting With The Pc
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. E1941T/E2041T/E2241T/E2341T/E2441T and power cord in order, then tighten the screw... - Page 14 Connecting the Display Connecting with the PC Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connect signal input cable of the signal cable. Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view.
-
Page 15: Control Panel Functions
Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. - Page 16 The best display mode is E1941T/E1941S : 1366 x 768 E2041T/E2041S : 1600 x 900 E2241T/E2241S/E2341T/E2441T: 1920 x 1080 When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub.
-
Page 17: On Screen Display (Osd) Control Adjustment
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. -
Page 18: On Screen Display(Osd) Selection And Adjustment
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu MENU BRIGHTNESS ORIGINAL RATIO COLOR TEMP (PRESET / USER) CONTRAST LANGUAGE FACTORY RESET SUPER ENERGY SAVING RESET NOTE The order of icons may differ depending on the model (17 to 22). - Page 19 On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Move : Select another sub-menu Sub menu Description To adjust the brightness of the screen. WIDE Switch to full screen mode according to input image signal. ORIGINAL Change the input image signal ratio to original.
- Page 20 On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Move : Select another sub-menu Description To adjust the contrast of the screen. To choose the language in which the control names are displayed. Restore all factory default settings except "LANGUAGE."...
- Page 21 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the SUPER ENERGY SAVING Button, then the main menu of the OSD appears.
- Page 22 On Screen Display(OSD) Selection and Adjustment Main menu Exit : Exit : Move : Select another sub-menu OK : Select TOTAL POWER REDUCTION : How much power is saved during using the monitor. TOTAL CO2 REDUCTION : Change the TOTAL POWER REDUCTION to CO2. Sub menu Description Turn on the SUPER ENERGY...
- Page 23 Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal. LED Saving means that how much power can be saved using WLED Panel instead of CCFL panel.
-
Page 24: Troubleshooting
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the display connected? Is the power indicator light on? Is the power indicator flickering? Do you see an "OUT OF RANGE" message on the screen? Do you see a "CHECK SIGNAL CABLE"... -
Page 25: Display Image Is Incorrect
Troubleshooting Display image is incorrect Display Position is incorrect. On the screen background, vertical bars or stripes are visible. Any horizontal noise appearing in any image or characters are not clearly portrayed. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. - Page 26 • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lg.com. • Make sure to check if the video card supports Plug&Play function.
-
Page 27: Specifications
Specifications Display 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0.300 mm x 0.300 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play... - Page 28 Specifications Display 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0.300 mm x 0.300 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
- Page 29 Specifications Display 50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8 cm 0.2766 mm x 0.2766 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
- Page 30 Specifications Display 50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8 cm 0.2766 mm x 0.2766 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
- Page 31 Specifications Display 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0.248 mm x 0.248 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
- Page 32 Specifications Display 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0.248 mm x 0.248 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
- Page 33 3.4 kg ( 7.49 lb ) Temperature 10 ˚C to 35 ˚C Humidity 10 % to 80 % non-Condensing Temperature -20 ˚C to 60 ˚C Humidity 5 % to 90 % non-Condensing ), Detached ( O ) E2341T 5.7 cm ( 2.24 inch )
- Page 34 Specifications Display 60.97 cm (24 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 60.97 cm 0.277 mm x 0.277 mm (Pixel pitch) Horizontal Freq. Sync Input Vertical Freq. Input Form Signal Input Video Input Input Form Resolution Recommend Plug&Play...
-
Page 35: Preset Modes (Resolution)
Specifications Preset Modes (Resolution) E1941T/E1941S *If you can't select 1366 x 768 in display property timing option, please update your video card driver from your video card vendor. Display Modes (Resolution) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624... - Page 36 Specifications E2241T/E2241S/E2341T/E2441T Display Modes (Resolution) Horizontal Freq. (kHz) 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050...
-
Page 37: Installing The Wall Mount Plate
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth. A type Remove the Stand Body and Stand Base from product in correct direction as shown in the picture B type... - Page 38 Installing the Wall mount plate Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.
- Page 39 Make sure to read the Safety Precautions before using the product. Keep the OWNER’S MANUAL(CD) in an accessible place for furture reference. The model and serial number of the SET is located on the back or one side of the SET. Record it below should you ever need service.