Advertisement
To start
Close and latch door. Press START/CANCEL pad.
To delay start
Close and latch door. Press DELAY START pad to
select desired delay time.
To select a new
Press desired cycle and/or option pad. The indicator
cycle or option
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To cancel cycle
Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock . . . . . . . . . . . Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
ULTIMATE/MAXX
NORMAL WASH
CHINA/CRYSTAL
ECO WASH
GLASSES
SPEED WASH
RINSE ONLY
SENSING
WASHING
SANITIZED
DRYING
CLEAN
TIME
WASH 1
RINSE 1
IN
8 MIN.
11 MIN.
MINUTES
WATER VALVE
FAN/DAMPER
PUMP MOTOR
DRAIN MOTOR
HEATER
DISPENSERS
TURBIDITY SENSE
*Note: The Sahara/Maxx Dry will extend drying time by approximately 20 min.
Display Codes (Readout)
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
1
FILL/DISPENSER
60 1
0
0
0
1
0
1
1
2
FILL
1
0
0
0
0
0
1
1
27
45
0
1
0
1
0
3
WASH/HEAT
0
1
1
4
PAUSE
0.4
0
0
0
1
0
0
1
1
0
1
0
1
0
5
WASH/HEAT
75
0
0
0
0
1
0
1
1
6
WASH/HEAT/DISP.
60
0
0
0
7
1
DRAIN
90
0
0
1
0
0
0
0
8
90
DRY
0
0
1
X
0
1
0
0
TOTAL
447
0
0
X - denotes selectable option
CLEAN LED stays on until door is opened or cycle is started.
RINSE 2
WASH 2
11 MIN.
32 MIN.
WATER HEAT DELAY
SENSING
---------------------- Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
WASHING
---------------------- Wash portion of cycle.
SANITIZED
-------------------- The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
DRYING
------------------------ Drying portion of cycle.
CLEAN
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
OPTION LED's Flashing
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
STATUS LED's Flashing
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is filled.
(Some models)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Uo
0
0
0
Fan damper
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Turbidity
Tu
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Hall sensor
HS
HS
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
Thermistor
Th
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Fan speed
Fan speed
UF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
Rinse aid
RA
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
RINSE 3
11 MIN.
Display Codes (LED)
Wiring Diagram
RINSE 4
RINSE 5
RINSE 6
15.5 MIN.
11 MIN.
11 MIN.
BK.......................... Black
Y-BK.............Yellow/Black
BU............................Blue
R-W..................Red/White
PK............................Pink
BK-W............. Black/White
R...............................Red
R-Y..................Red/Yellow
R-BK...............Red/Black
VIO..........................Violet
W............................White
TURBIDITY SENSOR/
THERMISTOR
DRY *(HOT OR COOL)
22 MIN.
WATER HEAT DELAY
Advertisement
