Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
Installation Instructions
NOTE:
These instructions describe installation
in a typical wood framed window with a wood
SLIDE-BY sash, or installation in a metal
C A S E M E N T w i n d o w. M o d i f i c a t i o n m a y b e
necessary when installing in windows made
differently than those shown in these instructions.
A high window accessory kit EA 103W is available
for window heights up to 62" (1575mm).
WARNING
WARNING
!
Electrical Shock and Personal Injury Hazard
Electrical ground is required on this appliance.
DO NOT ground to a gas line.
If cold water pipe is interrupted by plastic,
non-metallic
gaskets,
Materials, DO NOT use for grounding.
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
DO NOT modify power supply cord plug. If it
does not fit outlet, have a proper outlet
installed by a qualified electrician.
DO NOT have a fuse in the neutral or grounding
circuit. A fuse in the neutral, or grounding
circuit could result in an electrical shock.
DO NOT use an extension cord with this
appliance.
Failure to follow these instructions could result
electrical shock, serious injury, or death.
for Slider Casement
Meeting Electrical Requirements
or other insulating.
TABLE OF CONTENTS
SUBJECT
Installation in Wood Window
OBSERVE
ALL
AND ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE
THE POWER SUPPLY CORD GROUNDING PRONG.
NOTE: If codes permit, and a separate grounding
wire is used; it is recommended that a qualified
electrician determine that the grounding path is
adequate and not interrupted by plastic, non-metallic
gaskets, or other insulating materials.
RECEPTACLE WIRING
Receptacle wiring should be a minimum of 14 gauge.
Use copper wire only. It is your responsibility to
provide proper and adequate receptacle wiring,
installed by a qualified electrician.
ELECTRICAL REQUIREMENTS
A 115 volt (103 minimum, 126 maximum), 60 Hertz,
AC
only, 15
ampere fused electrical supply is
required. A time delay fuse or time delay circuit
breaker is also required. A separate circuit, serving
only this appliance, MUST be provided.
1
PAGE
1
2
2
4
5
6
LOCAL GOVERNING
P/N
CODES
Advertisement
Related Manuals for Frigidaire FAK127P1V
Summary of Contents for Frigidaire FAK127P1V
-
Page 1: Table Of Contents
Installation Instructions for Slider Casement NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal C A S E M E N T w i n d o w. M o d i f i c a t i o n m a y b e necessary when installing in windows made differently than those shown in these instructions. -
Page 2: Electrical Connection
Electrical ground is required on this appliance. Recommended grounding method: For your personal safety, this appliance must be grounded. This air conditioner includes a power supply cord with a 3-prong grounding plug. To minimize possible electrical shock hazard: -cord must be plugged into a mating 3-prong... - Page 3 Make sure you have all the necessary parts. Installation kit contents: Fig. A Installation Hardware Fig. 1A Installation Hardware Model 463AAC008BA Nuts(2) 3/8"Screws (4) Washers(2) 1"Screws (2) 7/16" Screws(2) End Cap & Leveling Leg (1) Support platform(1) Speed clips(2) Support angles (1) Sliders(2) Top retainer (1) Foam (1)
-
Page 4: Sliding Window Installation
Sliding Window Installation 1.Choose the installation site. It is imperative that window frame assembly and side of structure are adequate to support weight of unit. Reinforce if necessary. 2.Slide open one window sash to install support platform. 3.Loosely attach support angle to bottom of support platform ”... -
Page 5: Casement Window Installation
Casement Window Installation This air conditioner is designed to fit into most casement type windows. As shipped from factory, unit will fit into a minimum window opening 15 1/2” wide and 22” high. The preferred method of installation is through a closed or stationary window.