Frigidaire FAH12EN2T Installation Instructions Manual
Frigidaire fah12en2t: install guide
Hide thumbs
Also See for FAH12EN2T:
- Product information and technical manual (20 pages) ,
- Use and care manual (12 pages) ,
- Factory parts catalog (6 pages)
Related Manuals for Frigidaire FAH12EN2T
Summary of Contents for Frigidaire FAH12EN2T
-
Page 2: Installation Instructions
Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. CAUTION: When installation is complete, replacement unit MUST have a rearward slope as shown. - Page 3 Wall Sleeve Brands: Rear Louvers 10-1/4" Top View ⁄ " ‹ #1 Emerson 1. Redirect the louvers at the back of the wall sleeve as shown in the illustration. The use of pliers is recommended. 2. Attach (1) 1 ⁄ "x 3/8"x 26 3.
- Page 4 Trim Frame Assembly The purpose of trim frame is to cover space between wall sleeve and replacement unit cabinet. Each frame is made of four parts: 1. To assemble trim frame, insert snaps of side legs into top and bottom legs.
- Page 5 Attach the ground wire to the unit as shown. 8. Install the 1"x 1 #9 White-Westinghouse or Frigidaire 1. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille panel from the kit. The plastic grille panel is mounted to the inside of the wall sleeve at the rear flanges.
- Page 6 Wall Sleeve Brands: Rear Louvers 10-1/2" Top View ⁄ "‹ ⁄ ⁄ "‹ "‹ 7. Attach the ground wire to the unit as shown. #2 Fedders 1. Redirect the louvers at the back of the wall sleeve as shown in the illustration.
- Page 7 Wall Sleeve Brands: Rear Louvers 10-1/2" Top View ⁄ ⁄ "‹ "‹ ⁄ "‹ 6. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. 7. Install the 1"x 1 #3 Fedders or Friedrich 1.
- Page 8 5. Install the 1"x 1 and the unit. A flat bladed screwdriver or putty knife is recommended. #8 White-Westinghouse/Frigidaire/ 1. If the wall sleeve does not have a rear grille or louvered panel, install the plastic grille panel from the kit. The plastic grille panel is mounted to the inside of the wall sleeve at the rear flanges.
- Page 9 Wall Sleeve Brands: Rear Louvers 10" 9-1/2" Top View 10"‹ ⁄ ⁄ " ‹ "‹ 14"‹ 8"‹ 6. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. #7 Whirlpool 1. Redirect the louvers at the back of the wall sleeve as shown in the illustration.
- Page 10 Wall Sleeve Brands: Rear Louvers ⁄ ” 11" Top View ⁄ "‹ ⁄ ⁄ "‹ "‹ 5. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. 6. Install the 1"x 1 #4 General Electric/Hotpoint 1.
- Page 11 Wall Sleeve Brands: Rear Louvers 10" 9-1/2" Top View 10"‹ ⁄ ⁄ "‹ "‹ 5. Attach the ground wire to the unit as shown. 6. Install the 1"x 1 flat bladed screwdriver or putty knife is recommended. #5 Sears or Carrier (51S Series) 1.
- Page 12 Wall Sleeve Brands: Rear Louvers 10" 9-1/2" Top View 10"‹ ⁄ ⁄ "‹ "‹ 5. Install the new unit into the wall sleeve. Attach the ground wire to the unit as shown. 6. Install the 1"x 1 #6 Whirlpool 1. Redirect the louvers at the back of the wall sleeve as shown in the illustration.