OLS-32/40/46/70/8201NGB/P Safety Instructions Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire.
Page 4
OLS-32/40/46/70/8201NGB/P Do not disconnect the power cord while using the LCD Display. A surge may be caused by the separation and may damage the LCD Display. Do not use the power cord when the connector or plug is dusty.
Page 5
OLS-32/40/46/70/8201NGB/P Do not place the LCD Display face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury.
Page 6
OLS-32/40/46/70/8201NGB/P Do not install the product on an unstable, uneven surtace or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations mayshorten the lifetime of the product or may cause the product to catch fire.
Page 7
OLS-32/40/46/70/8201NGB/P Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
OLS-32/40/46/70/8201NGB/P Introduction LCD Display Manual User Manual CD Cable RGB Cable AC Power Cable HDMI Cable (Option) Other Remote Control Batteries (AAA X 2) 8 of 38 3/30/2012 페이지...
Page 9
OLS-32/40/46/70/8201NGB/P Front 1. IR Aim the remote control towards this spot on the LCD Display. 2. LED LCD Power Status display(On : BLUE / Off : RED) 3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down) a) Power : Turns the LCD Display On/ Off.
Page 10
OLS-32/40/46/70/8201NGB/P Rear 1. AC Power S/W On/Off 2. AC Power In (100V ~ 240V) 3. HDMI Input 4. DVI(HDMI Jack) Output 5. PC Input 6. RS-232 Output 7. RS-232 Input 8. Component(Input) 9. Component(Output) 10. AV Input 11. AV Output 12.
OLS-32/40/46/70/8201NGB/P SICP (Serial Interface Communication Protocol) This document defines all the command and messages exchanged between the Master (a PC or the other controller) and the Slave (the displays). It also describes the ways to send or read the commands or the messages.
Page 14
OLS-32/40/46/70/8201NGB/P 6. OK Acknowledgement The acknowledgement will be sent by the display to the computer to verify that the command has been successfully received and executed. This format for this acknowledgement is as follows: ex) <STX>001PWR#OFF#<ETX> ( Set ID : 1 , Power Off Acknowledgement )
Page 15
OLS-32/40/46/70/8201NGB/P 9. Command List ♦ Power On/Off (PWR) 0x0f 0x0d ASCII (capital letter) - ID1 ~ ID3 : Set ID (“001” ~ “100”) - DA1 ~ DA3 : “-ON” : Power On “OFF” : Power Off Ex) <STX>001PWRWOFF0<ETX> ( Power Off ) Acknowledge =>...
OLS-32/40/46/70/8201NGB/P Remote control 1. POWER : Turns the LCD Display On and Off 2. UP : Control the UP cursor in the menu 3, LEFT : Control the LEFT cursor in the menu 4, RIGHT : Control the RIGHT cursor in the menu...
OLS-32/40/46/70/8201NGB/P Viewing the Menus ◆ Press the MENU button. The main menu is displayed on the screen. Its left side has five icons: Picture, Sound, Setup and PIP. Changing the Picture Standard. 1. Press the MENU button to display the menu.
Page 22
OLS-32/40/46/70/8201NGB/P Customizing the Picture Settings. Your DID Set has several setting options that allow you to control the picture quality. 1. Press the MENU button to display the menu. 2. Press the ENTER button. 3. Press the ▲ or ▼ button to select Custom, then press the ENTER button.
Page 23
OLS-32/40/46/70/8201NGB/P ◆Cool 1: This results in a blue tone. ◆Cool 2: This results in a more blue tone. ◆Normal: This is standard color setting. ◆Warm1: This results in a reddish tone. ◆Warm2: This results in a more reddish tone. Selecting the Picture Size.
Page 24
OLS-32/40/46/70/8201NGB/P Selecting the Multi Edge Adj.Mode. 1. Press the MENU button to display the menu. 2. Press the ENTER button. 3. Press the ▲ or ▼ button to select Multi Edge Adj.Mode, then press the ENTER button. 4. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Page 25
OLS-32/40/46/70/8201NGB/P ◆Top Left: This Adjust Horizontal(Left) / Vertical(Top) Edge Gap ◆Center: This Adjust Horizontal(Center) / Vertical(Center) Edge Gap ◆Bottom Right: This Adjust Horizontal(Right) / Vertical(Bottom) Edge Gap 25 of 38 3/30/2012 페이지...
Page 26
OLS-32/40/46/70/8201NGB/P Viewing the Picture in Picture (PIP). (Available in PC mode) You can display a sub picture within the main picture of PC. In this way you can watch monitor the video input from any connected devices while watching PC.
Page 27
OLS-32/40/46/70/8201NGB/P You can select a source size of the sub-picture. ◆ Position: You can select a source position of the sub-picture. ◆ Swap You can select the main screen and the sub screen will swap 27 of 38 3/30/2012 페이지...
Page 28
OLS-32/40/46/70/8201NGB/P ◆ Sound Select. You can select the sound of the sub screen can be selected when PIP is being displayed Reset. 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Setup, then press the ENTER button.
Page 29
OLS-32/40/46/70/8201NGB/P Time Features. 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 3. Press the ▲ or ▼ button to select Timer, then press the ENTER button.
Page 30
OLS-32/40/46/70/8201NGB/P OSD Tone. 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 3. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Page 31
OLS-32/40/46/70/8201NGB/P Dimming. 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Setup->Dimming then press the ENTER button. 3. Select the required option by pressing the ▲ or ▼ button - Auto Dimming : On or Off : If want Auto Control the Dimming by lux value then select On, or not Off - Dim Level : If auto dimming off, you can adjust manual dimming.
Page 32
OLS-32/40/46/70/8201NGB/P Heat control. 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Setup->Heat Control then press the ENTER button. 3. Select the required option by pressing the ▲ or ▼ button -Fan Control : Off/On/Auto : If you want always fan off then Off or always on then On or Auto control then Auto.
OLS-32/40/46/70/8201NGB/P Specifications OLS-3201NGB Items Specifications Display Size 32 Inch (16:9) : LCD / S-PVA TFT Response Time 8 ms(Typ G to G) Pixel Size 0.51075(H) x 0. 51075 (V) mm Resolution 1366 x 768 (WXGA) Colors 8 bit, 16.7M Colors...
Page 34
OLS-32/40/46/70/8201NGB/P OLS-4001NGP Items Specifications Display Size 40 Inch (16:9) : LCD / S-PVA TFT Response Time 8 ms(Typ G to G) Pixel Size 0.46125(H) x 0. 46125 (V) mm Resolution 1920 x 1080 (WUXGA) Colors 8 bit, 16.7M Colors 40 inch Brightness 700cd/㎡...
Page 35
OLS-32/40/46/70/8201NGB/P OLS-4601NGP Items Specifications Display Size 46 Inch (16:9) : LCD / S-PVA TFT Response Time 8 ms(Typ G to G) Pixel Size 0.53025(H) x 0. 53025 (V) mm Resolution 1920 x 1080 (WUXGA) Colors 8 bit, 16.7M Colors 46 inch Brightness 700cd/㎡...
Page 36
OLS-32/40/46/70/8201NGB/P OLS-8201NGB Items Specifications Display Size 82 Inch (16:9) : LCD / S-PVA TFT Response Time 8 ms(Typ G to G) Pixel Size 0.9405(H) x 0.9405(V) mm Resolution 1920 x 1080 (WUXGA) Colors 8 bit, 16.7M Colors 82 inch Brightness 450cd/㎡...
Page 37
OLS-32/40/46/70/8201NGB/P Input / Output Port Description Items Specifications H Frequency Range : 20 ~ 80 kHz V Frequency Range : 55 ~ 75 Hz PC (Analog RGB) Maximum resolution :1920x1080 60Hz Maximum pixel rate : 162 MHz/110MHz H Frequency Range : 20 ~ 80 kHz...