JVC GR-D370UC Service Manual page 7

3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
Disassembly procedure
STEP Fig.
PART NAME
No. No.
FA1-1
[1]
UPPER ASSY
FA1-2
[2]
OPE PWB ASSY FA2-1
[3]
COVER (HINGE) FA2-2
[4]
MONITOR ASSY FA2-3
[5]
SPEAKER
FA2-4
[6]
ZOOM UNIT
[7]
FRONT ASSY FA3
[8]
CASS.COVER FA4
[9]
VF ASSY FA5
[10]
REAR COVER ASSY FA6
[11]
LOWER CASE ASSY FA7
[12]
REAR PWB ASSY
FA8
[13]
OP BLOCK ASSY
[14]
MAIN BKT ASSY FA9
[15]
MAIN PWB ASSY
FA10
[16]
FRAME ASSY
NOTE1a:
Open the MONITOR ASSY, and then remove the screw
(No.7) which is next to the DV terminal.
NOTE1b:
When removing the UPPER ASSY, be careful in handling
the FPC.
Also, be careful in wiring the FPC when attaching the UP-
PER ASSY.
NOTE2a:
During the procedure, be careful in handling the SWITCH.
When attaching, leave the MONITOR ASSY open.
NOTE2b:
When attaching, be careful in wiring.
NOTE2c:
During the procedure, be careful not to lose KNOB(SLIDE).
NOTE5:
When attaching, be careful in wiring (SPEAKER).
NOTE7:
When attaching, be careful to avoid placing the WIRE (MIC)
on the front side, and make sure to place the WIRE (MIC) on
the connector.
NOTE8:
Pull out the GLIP BELT first.
NOET9a:
When removing the VF ASSY, pull out the FPC on the CCD
BOARD ASSY from the MAIN BOARD ASSY first.
NOTE9b:
When removing, pull out the FPC by lifting up the VF AS-
SEMBLY.
NOTE10:
During the procedure, release the LOWER CASE ASSY in
the direction of an arrow.
NOTE11:
During the procedure, be careful in handling the FPC.
POINT NOTE
S1a,2(S1b),3(S1c),S1d NOTE1a
L1a,L1b,CN1 NOTE1b
CN2a,b,c,S2a,4(S2b),KNOB(SLIDE) NOTE2a,b,c
2(S3) -
2(S4),2(L4) -
BKT.(HINGE),2(L5) NOTE5
3(S6),L6 -
S7a,2(S7b),2(L7a),2(L7b),CN7 NOTE7
GRIP BELT,4(S8),3(L8) NOTE8
CN9a,S9a,b,c,CN9b NOTE9a,b
S10a,b,c,L10a,b NOTE10
2(S11),CN11 NOTE11
S12,L12,CN12 NOTE12
CN13,2(L13) NOTE13
3(S14),L14a,b -
CN15a,b,c,d,e,S15,L15a,b -
4(S16) -
NOTE12:
During the procedure, be careful not to damage the
SWITCH.
During the procedure, leave the CASS. COVER closed.
NOTE13:
When attaching, be careful to avoid any uplift or unevenness
of the CUSHION (OP).
Destination of connectors
CN.
CONNECTOR
No.
CN1 MAIN CN103
CN2a OPE CN403
CN2b OPE CN404
CN2c OPE CN402
CN7 MAIN CN2601
CN9a MAIN CN4201
CN9b MAIN CN7801
CN11 REAR CN502
CN12 MAIN CN101
CN13 MAIN CN4901
CN15a MAIN CN1604
CN15b MAIN CN1603
CN15c MAIN CN1602
CN15d MAIN CN3501
CN15e MAIN CN1601
PIN
No.
OPE CN401 30
ZOOM UNIT - 8
SPEAKER - 2
MONITOR CN7601 18/21
MIC - 4
CCD CN5001 20
VF CN7001 24/23
POWER UNIT - 7
REAR CN504 32
OP BLOCK - 26
SENSOR - 16
CAPSTAN MOTOR - 18
DRUM MOTOR - 11
HEAD - 8
LOADING MOTOR
- 8
ROTARY ENCODER SW
(No.YF124)1-7