Vivotek PZ8111 Quick Installation Manual
10x zoom multiple streams poe
Hide thumbs
Also See for PZ8111:
- User manual (152 pages) ,
- Quick installation manual (12 pages) ,
- Quick installaion manual (12 pages)
Related Manuals for Vivotek PZ8111
Summary of Contents for Vivotek PZ8111
- Page 1 10x Zoom‧Multiple Streams‧PoE PZ8111/21/11W/21W This guide describes the basic functions of PZ8111/21/11W/21W. All detailed information is described in the user’s manual.
- Page 2 Warning Before Installation Power off the Network Camera Keep the Network Camera assoon as smoke or unusual odors away from water. If the Network are detected. Camera becomes wet, power off immediately. Contact your distributor in the event of Contact your distributor in the event of occurrence.
- Page 3 Do not place the Network Camera Do not touch the Network Camera on unsteady surfaces. during a lightning storm. Do not disassemble the Network Do not drop the Network Camera. Camera. Do not insert sharp or tiny objects Do not manually pan and tilt the into the Network Camera.
-
Page 4: Package Contents
Package Contents PZ8111/21/11W/21W Power Adapter Antenna Screws (PZ8111W/21W Only) Quick Installation Guide / Software CD Warranty Card Ceiling Mount Brackets A/V Cable EN - 3... -
Page 5: Physical Description
Physical Description Front Panel Lens Built-in Microphone Status LED Power/MIC Activity Back Panel Antenna (PZ8111W / PZ8121W Only) Microphone In Ethernet 10/100 AV Out RJ45 Socket Power cord socket Recessed Reset Button General I/O External/Internal Terminal Block Microphone Switch EN - 4... -
Page 6: Hardware Installation
Hardware Installation Mounting the Network Camera 1. Attach ceiling mount bracket A to the Network Camera and secure it with two small screws. 2. Drill three pilot holes into the ceiling; hammer the plastic anchors into the holes. 3. Fasten ceiling mount bracket B to the ceiling with three screws. 4. -
Page 7: Network Deployment
Network Deployment General Connection (without PoE) 1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block. 2. Connect the camera to a switch via Ethernet cable. 3. Connect the supplied power cable from the camera to a power outlet. 1: Power 2: Digital output 3: Digital input... -
Page 8: Power Over Ethernet (Poe)
Power over Ethernet (PoE) When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the camera to a PoE e abled switch via Ethernet cable. PoE switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a... -
Page 9: Assigning An Ip Address
“Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on the bottom of your device to connect to the Network Camera via Internet Explorer. -
Page 10: Ready To Use
Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or recording software. For further setup, please refer to the user's manual on the software CD. EN - 9... - Page 11 Configure the Wireless Connection (PZ8111W/21W only) 1. Check the SSID for your wireless access point (AP). 2. Go to the PZ8111W/21W's Configuration page > Advanced mode > Wireless LAN. 3. Type in the SSID the same as your AP. 4. Select the Wireless mode as "Infrastructure". 5.
- Page 12 625015200G P/N: Ver.1.0 Copyright 2011 VIVOTEK INC. All rights reserved.