Vector TLC3-FCR-M2-24 Engineering Manual

TLC3-FCR-M
Programmable PID Fan Coil controller
Features
 Proven PID controls algorithm reduces room temperature
fluctuations and energy consumption
 Low power energy consumption: < 1W per unit
 Temperature control for 2- and 4-pipe fan coil systems.
 Automatic fan control for three stage fans.
 Cost saving option with Economy functionality and set point
limitations
 Control for modulating heating, cooling and fan only operation
modes
 Password protected programmable user and control parameters
Setpoint range limitation
o
Access control for setpoints, fan speeds and mode change
o
Access control for heat/cool change and time programs
o
Select your display contents
o
Selectable behavior after return from power failure
o
 Temperature display in Celsius or Fahrenheit
Deluxe Version:
 Clock and time schedule functions with power failure protection
 Blue backlight for LCD
 Infrared remote controller option:
With special features for Boost and delayed switching on or off
Applications
 Air Only Systems:
Constant or Variable Air Volume systems with three stage fans for single or dual duct systems
o
 Air/Water Systems:
Fan Coil units for 2-pipe or 4-pipe systems
o
radiator control, chilled ceiling
o
 Simple individual room control for hotel rooms, meeting rooms, etc.
 PID-Control of up to 2 modulating valves for heating and cooling
General Description
The TLC3-FCR-M is a stand-alone electronic fan coil controller with one control loop. The TLC3-FCR-M2 is designed for
2-pipe modulating fan coil systems and features 1 NTC temperature sensor input, one external passive input for
temperature or open contact, three binary outputs (Relays) and one analog output (0-10VDC).
The TLC3-FCR-M4 is designed for 4-pipe modulating fan coil systems and features 1 NTC temperature sensor input,
three binary outputs (Relays) and two analog outputs (0-10VDC) for heating and cooling.
A detailed parameterization is possible with the use of a simple configuration routine. The TLC3-FCR-M can be
configured using the standard operation terminal. No special tools or software is required.
Ordering
Item Name
TLC3-FCR-M2-24
TLC3-FCR-M2-24-W01
TLC3-FCR-M2-230
TLC3-FCR-M2-230-W01
TLC3-FCR-M2-D-24
TLC3-FCR-M2-D-24-W01
TLC3-FCR-M2-D-230
TLC3-FCR-M2-D-230-W01
TLC3-FCR-M4-24
TLC3-FCR-M4-230
TLC3-FCR-M4-D-24
TLC3-FCR-M4-D-230
Selection of fans
Do not directly connect devices that exceed 2A. Observe startup current on inductive loads! Do not connect more than
one fan coil unit to one controller.
Modulating Actuators:
Choose actuators with an input signal type of 0-10V DC or 2-10V DC. Observe maximal signal current of 1mA!
Doc: 70-00-0181, V3.0 Date: 20120424
Subject to alteration
Item code Variant
40-10 0131 Standard
40-10 0131-01 Cooling only
40-10 0100 Standard
40-10 0100-01 Cooling only
40-10 0136 Deluxe
40-10 0136-01 Cooling only
40-10 0101 Deluxe
40-10 0101-01 Cooling only
40-10 0132 Standard
40-10 0104 Standard
40-10 0137 Deluxe
40-10 0105 Deluxe
© Vector Controls GmbH, Switzerland
TLC3-FCR-M Engineering Manual
Power Features
24VAC/DC
Fan coil controller with:
230VAC
1 TI int, 1 external input
3 DO (Relay) Fan control
24VAC/DC
1 AO (0-10VDC) PID valve control
230VAC
24VAC/DC
1 TI int
230VAC
3 DO (Relay) Fan control
24VAC/DC
2 AO (0-10VDC) PID valve control
230VAC
Page 1