Related Manuals for TRENDnet TEW1750ACV2
Summary of Contents for TRENDnet TEW1750ACV2
- Page 1 802.11ac(draft 2.0) TEW-815DAP Wireless Access Point TEW-815DAP Rev 0.1 User Manual...
- Page 2 Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 3: Europe - Eu Declaration Of Conformity
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: +A11: 2009 EN60950-1:2006 Safety of Information Technology Equipment... - Page 4 output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
- Page 5 Česky [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se [Czech] základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in [German]...
-
Page 6: European Union Notice
Nederlan Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in ds [Dutch] overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma [Maltese] mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. -
Page 7: Trademark Recognition
Compliance with these directives implies conformity to the following European Norms: EN 60950 Product Safety EN 300 328 Technical requirement for radio equipment EN 301 489-1/-17 General EMC requirements for radio equipment EN 301 893 V1.5.1(2008-12) Trademark recognition All product names used in this manual are the properties of their respective owners and are acknowledged. - Page 8 Getting Started with the TEW-815DAP Congratulations on purchasing the TEW-815DAP! This manual provides information for setting up and configuring the TEW-815DAP. This manual is intended for both home users and professionals. The following conventions are used in this manual: THE NOTE SYMBOL INDICATES ADDITIONAL INFORMATION ON THE TOPIC AT HAND.
-
Page 9: Package Contents
Package Contents TEW-815DAP 802.11ac(draft 2.0)3x3 Gigabit Wireless Access Point CAT-5 Ethernet Cable (All the TEW-815DAP’s Ethernet ports are Auto-MDIX) Power Adapter (12V, 2A) CD-ROM with Software and Manual Quick Installation Guide Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product. -
Page 10: Wireless Lan Networking
Wireless LAN Networking This section provides background information on wireless LAN networking technology. Consult the Glossary for definitions of the terminology used in this section. HE INFORMATION IN THIS SECTION IS FOR YOUR REFERENCE. HANGING NETWORK SETTINGS AND PARTICULARLY SECURITY SETTTINGS SHOULD ONLY BE DONE BY AN AUTHORIZED ADMINISTRATOR. - Page 12 When a number of wireless stations are connected using a single access point, you have a Basic Service Set (BSS). In the ESS diagram below, communication is done through the access points, which relay data packets to other wireless stations or devices connected to the wired network. Wireless stations can then access resources, such as a printer, on the wired network.
- Page 13 connection. In the diagram below, when the user moves from BSS (1) to BSS (2) the WLAN client devices automatically switches to the channel used in BSS (2). Roaming in an ESS network diagram...
- Page 14 Introduction The TEW-815DAP is an high-performance, 802.11ac (draft 2.0)3x3 Gigabit Wireless Access Point wireless Access Point that supports high-speed wireless networking at home, at work or in public places. 867Mbps Unlike most Access Points, the TEW-815DAP provides data transfers at up to when using 11AC connection.
-
Page 15: Hardware Overview
Hardware Overview LED Indications: (from bottom to top) PWR/WPS Wireless 2.4G Wireless 5G Rear panel: (from bottom to top) • DC-IN • POWER SWITCH( EU) • Installation Considerations The TEW-815DAP 802.11ac(draft 2.0)3X3 Gigabit Wireless Access Point lets you access your network, using a wireless connection, from virtually anywhere within its operating range. -
Page 16: Getting Started
Getting Started For a typical wireless setup at home, please do the following: You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem. Connect the Cable or DSL modem to the TEW-815DAP Access Point (WAN port). -
Page 17: Network Status
Network Status Show your network status... -
Page 18: Wireless Setting
Wireless Setting: You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Security Mode. The Access Point can be set simply with only the minimum setting items. - Page 20 Administrator Status:...
- Page 22 The device status. Management:...
- Page 23 You may configure administrator account and password. Admin Password Enter a password for the user "admin", who will have full access to the Web-based management interface. Device Name The name of the Access Point can be changed here. Enable Dynamic DNS Enable this option only if you have purchased your own domain name and registered with a dynamic DNS service provider.
-
Page 24: Upload Firmware
Upload Firmware: Once you have a firmware update on your computer, use this option to browse for the file and then upload the information into the Access Point. -
Page 25: Setting Management
Setting Management: Export Settings This option allows you to export and then save the Access Point's configuration to a file on your computer. Be sure to save the configuration before performing a firmware upgrade. Import Settings Use this option to restore previously saved Access Point configuration settings. Load Factory Defaults This option restores all configuration settings back to the settings that were in effect at the time the Access Point was shipped from the factory. - Page 26 This restarts the Access Point. It is useful for restarting when you are not near the device.
- Page 27 Status: The device status...
- Page 28 IPv6 Status: System log:...
- Page 29 This page can be used to set remote log server and show the system log.
-
Page 30: Lan Setting
Setup LAN Setting: This page allows you to configure the LAN of the Access Point IP Address The IP address of the this device on the local area network. Assign any unused IP address in the range of IP addresses available for the LAN. Subnet Mask The subnet mask of the local area network. -
Page 31: Ipv6 Setting
MAC Address To input the MAC address of your system, enter it in manually or connect to the Access Point's Web-Management interface from the system and click the Copy Your PC's MAC Address button. A MAC address is usually located on a sticker on the bottom of a network device. The MAC address is comprised of twelve digits. - Page 32 LAN IPv6 Setting 6to4 6to4 is provided as a transition for migrating from IPv4 to IPv6. It allows IPv6 packets to be transmitted over an IPv4 network through the automatic tunneling technology, and routes traffic between 6to4 and IPv6 networks. Native IPv6 only Native IPv6 refers to the network where IPv6 is the only transport protocol running.
-
Page 33: Multiple Ssid
Wireless Multiple SSID: You could configure the minimum number of Wireless settings for communication, such as Network Name (SSID) and Security Mode. The Access Point can be set simply with only the minimum setting items. Wireless Network Name (SSID) When you are browsing for available wireless networks, this is the name that will appear in the list (unless Visibility Status is set to Invisible, see below). - Page 34 network name. Add up to three additional SSIDs to create virtual wireless networks from one wireless Access Point Access Point device. Add Additional Wireless Network Name (SSID) To add additional wireless Network Names simply add the name to the Multiple SSID field and click on apply at the bottom of the page.
- Page 35 WDS: This page allows you to configure Wireless Distribution System (WDS) for the wireless LAN interfaces. Wireless Distribution System (WDS) When WDS is enabled, this access point functions as a wireless repeater and is able to wirelessly communicate with other APs via WDS links. A WDS link is bidirectional; so this AP must know the MAC Address (creates the WDS link) of the other AP, and the other AP must have a WDS link back to this AP.
- Page 36 (Note that WDS security is incompatible with mixed mode, like WPAPSK+WPA2PSK mixed, WEP AUTO and 802.1x, both feature cannot be used at the same time). Configuring WDS with TEW-815DAP Enable the option for WDS and input the MAC Address of the wireless device that also supports WDS in to the blank fields.
- Page 37 Advanced: Use the Advanced Setup page to make detailed settings for the Wireless. Advanced Setup includes items that are not available from the Basic Setup page, such as Beacon Interval, etc Beacon Interval Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Period value between 20 and 1000.
- Page 38 Fragmentation Threshold Wireless frames can be divided into smaller units (fragments) to improve performance in the presence of RF interference and at the limits of RF coverage. Fragmentation will occur when frame size in bytes is greater than the Fragmentation Threshold. This setting should remain at its default value of 2346 bytes.
- Page 39 WPS: Enable Enable the WPS feature. PIN Settings A PIN is a unique number that can be used to add the Access Point to an existing network or to create a new network. The default PIN may be printed on the bottom of the Access Point. For extra security, a new PIN can be generated.
- Page 40 Generate New PIN Create a random number that is a valid PIN. This becomes the Access Point's PIN. You can then copy this PIN to the user interface of the registrar.
- Page 41 Glossary 802.11 A family of specifications for wireless local area networks (WLANs) developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). Access Control List ACL. This is a database of network devices that are allowed to access resources on the network.
- Page 42 AARP. Used to map the MAC addresses of Apple computers to their AppleTalk network addresses, so that conversions can be made in both directions. Application layer 7th Layer of the OSI model. Provides services to applications to ensure that they can communicate properly with other applications on a network.
- Page 43 Bit rate The amount of bits that pass in given amount of time Bit/sec Bits per second BOOTP Bootstrap Protocol. Allows for computers to be booted up and given an IP address with no user intervention Bottleneck A time during processes when something causes the process to slowdown or stop all together Broadband A wide band of frequencies available for transmitting data Broadcast...
- Page 44 Information that is stored on the hard drive of your computer that holds your preferences to the site that gave your computer the cookie Data Information that has been translated into binary so that it can be processed or moved to another device Data Encryption Standard Uses a randomly selected 56-bit key that must be known by both the sender and the receiver...
- Page 45 DMZ: A single computer or group of computers that can be accessed by both users on the Internet as well as users on the Local Network, but that is not protected by the same security as the Local Network. DHCP Dynamic Host Configuration Protocol: Used to automatically assign IP addresses from a predefined pool of addresses to computers or devices that request them Digital certificate:...
- Page 46 IP address that is assigned by a DHCP server and that may change. Cable Internet providers usually use this method to assign IP addresses to their customers. Extensible Authentication Protocol Email Electronic Mail is a computer-stored message that is transmitted over the Internet Encryption Converting data into cyphertext so that it cannot be easily read Ethernet...
- Page 47 Sending and Receiving data at the same time Gain The amount an amplifier boosts the wireless signal Gateway A device that connects your network to another, like the internet Gbps Gigabits per second Gigabit Ethernet Transmission technology that provides a data rate of 1 billion bits per second Graphical user interface H.323 A standard that provides consistency of voice and video transmissions and compatibility for...
- Page 48 HTTP over SSL is used to encrypt and decrypt HTTP transmissions A networking device that connects multiple devices together ICMP Internet Control Message Protocol IEEE Institute of Electrical and Electronics Engineers IGMP Internet Group Management Protocol is used to make sure that computers can report their multicast group membership to adjacent Access Points Internet Information Server is a WEB server and FTP server provided by Microsoft Internet Key Exchange is used to ensure security for VPN connections...
- Page 49 Intrusion Detection A type of security that scans a network to detect attacks coming from inside and outside of the network Internet Protocol IP address A 32-bit number, when talking about Internet Protocol Version 4, that identifies each computer that transmits data on the Internet or on an Intranet IPsec Internet Protocol Security Internetwork Packet Exchange is a networking protocol developed by Novel to enable their...
- Page 50 The amount of time that it takes a packet to get from the one point to another on a network. Also referred to as delay Light Emitting Diode Legacy Older devices or technology Local Area Network A group of computers in a building that usually access files from a server LPR/LPD "Line Printer Requestor"/"Line Printer Daemon".
- Page 51 Maximum Transmission Unit is the largest packet that can be transmitted on a packet-based network like the Internet Multicast Sending data from one device to many devices on a network Network Address Translation allows many private IP addresses to connect to the Internet, or another network, through one IP address NetBEUI NetBIOS Extended User Interface is a Local Area Network communication protocol.
- Page 52 Open Systems Interconnection is the reference model for how data should travel between two devices on a network OSPF Open Shortest Path First is a routing protocol that is used more than RIP in larger scale networks because only changes to the routing table are sent to all the other Access Points in the network as opposed to sending the entire routing table at a regular interval, which is how RIP functions Password...
- Page 53 Point-to-Point Protocol over Ethernet is used to connect multiple computers to a remote server over Ethernet PPTP Point-to-Point Tunneling Protocol is used for creating VPN tunnels over the Internet between two networks Preamble Used to synchronize communication timing between devices on a network Quality of Service RADIUS Remote Authentication Dial-In User Service allows for remote users to dial into a central server...
- Page 54 Algorithm used for encryption and authentication Server A computer on a network that provides services and resources to other computers on the network Session key An encryption and decryption key that is generated for every communication session between two computers Session layer The fifth layer of the OSI model which coordinates the connection and communication between applications on both ends...
- Page 55 Service Set Identifier is a name for a wireless network Stateful inspection A feature of a firewall that monitors outgoing and incoming traffic to make sure that only valid responses to outgoing requests are allowed to pass though the firewall Subnet mask Determines what portion of an IP address designates the Network and which part designates the Host...
- Page 56 Universal Plug and Play A standard that allows network devices to discover each other and configure themselves to be a part of the network Upgrade To install a more recent version of a software or firmware product Upload To send a request from one computer to another and have a file transmitted from the requesting computer to the other UPnP Universal Plug and Play...
- Page 57 Wide Area Network Windows Connect Now. A Microsoft method for configuring and bootstrapping wireless networking hardware (access points) and wireless clients, including PCs and other devices. Wireless Distribution System. A system that enables the interconnection of access points wirelessly. Web browser A utility that allows you to view content and interact with all of the information on the World Wide Wired Equivalent Privacy is security for wireless networks that is supposed to be comparable to that of a wired network...
- Page 58 xDSL A generic term for the family of digital subscriber line (DSL) technologies, such as ADSL, HDSL, RADSL, and SDSL. Yagi antenna A directional antenna used to concentrate wireless signals on a specific location...