Related Manuals for Rockford Fosgate TM400X2ad
Summary of Contents for Rockford Fosgate TM400X2ad
- Page 1 AMPLIFIERS TM400X2ad • TM400X4ad • TM500X1br TM750X1bd • TM1000X5ad Installation & Operation...
-
Page 2: Table Of Contents
17 Limited Warranty Information ©2014 Rockford Corporation. All Rights Reserved. ROCKFORD FOSGATE and associated logos where applicable are registered trademarks of Rockford Corporation in the United States and/or other countries. All other trademarks are the property of their respective owners. Specifications subject to change without notice. -
Page 3: Specifications
* Rated power when amplifier is wired in a bridged configuration. CEA 2006 Power ratings on Rockford Fosgate amplifiers conform to CEA-2006 industry standards. These guidelines mean your amplifier’s output power ratings are REAL POWER numbers, not inflated marketing ratings. -
Page 4: Design Features
Selectable switch for High-Pass (HP) or All Pass (AP) or Low-Pass (LP). Remote Punch Level Control Remotely control the output level of the amplifier. (TM400X2ad, TM500X1br, TM750X1bd & TM1000X5ad) Signal Input The RCA inputs are capable of accepting signal from either high-level (speaker) to low-level(RCA). - Page 5 TM400X2ad, TM400X4ad & TM1000X5ad-F/R only Power/REM Terminals The power and ground quick connector will accommodate up to 8 AWG (TM400X2ad, TM400X4ad, TM500X1br & TM750X1bd) and 4 AWG (TM1000X5ad). The REM terminal is used to remotely turn-on and turn-off the amplifier when Speaker Terminals +12V DC is applied.
-
Page 6: Installation
• 16 AWG 4-pin Molex Speaker • Operation CD- (Test Tones & working on any vehicle. Connector(s) - (TM400X2ad, Installation Manual) T4004ad & TM1000X5ad) 7. Never run wires underneath the vehicle. Running the wires inside the •... -
Page 7: Battery And Charging
Authorized is active. With the auto turn-on active, the REM becomes an output to turn Rockford Fosgate Dealer for installation. on/off up to two additional amplifiers or other accessories. Before installation, disconnect the battery 7. - Page 8 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.1...
- Page 9 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.2...
- Page 10 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.3...
- Page 11 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.4...
- Page 12 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.5...
- Page 13 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery. illus.-2.9...
- Page 14 ATVs, Golf Carts or Motorcycle When using amplifiers on ATVs, Golf Carts or Motor- cycles, Rockford Fosgate recommends to run both GND (negative) and B+ (positive) cables from the amplifier directly to the battery.
-
Page 16: Operation
Operation Input Clip Indicator Setup Step 6. Decrease the source unit volume slightly until the light turns illus.-3.1 completely off. This establishes your maximum source unit volume for adjusting the Output Clip Indicator. Step 1. Be sure to disconnect all speakers from the amplifier. -
Page 17: Adjusting Crossover Frequency
(speaker) input. When utilizing high-level for input to the “ON” position for this feature to be active. The TM400X2ad needs to signal the auto turn-on feature is active. With the auto turn-on active, be switched to “Low-Pass” for this feature to be active. This feature is not REM becomes an output to turn on/off up to two additional amplifiers or available on the TM400X4ad. -
Page 18: Troubleshooting
Troubleshooting Troubleshooting Check Amplifier if you experience excess Engine Noise. NOTE: If you are having problems after installation follow the Troubleshooting procedures below. 1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires. Check Amplifier for proper connections. Verify that POWER light is on. - Page 19 What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by authorized Rockford Fosgate dealers in the United States of America. Prod- ucts purchased by consumers from an Authorized Rockford Fosgate Dealer in another country are covered only by that country’s Distributor and not by Rockford Corporation.
- Page 20 Installation assistance available at www.rockfordfosgate.com/rftech 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G A T E . C O M...