Control Panel Buttons And Lights - Epson FX-2190 Product Information Manual

Control Panel Buttons and Lights

Button/Light Function
1 Font button Selects one of the fonts. See "Selecting a
Font and Pitch" on page 8.
Font lights Indicate which font is selected.
2 Reset When you press both the Font and Pitch
buttons simultaneously, the printer clears the
buffer and restores its default settings.
3 Pitch button Selects one of the pitch settings. See
"Selecting a Font and Pitch" on page 8.
Pitch lights Indicate which pitch is selected.
4 Tear Off/Bin Feeds continuous paper forward to the
button tear-off position.
Feeds continuous paper backward from the
tear-off position to the top-of-form position.
Selects a cut-sheet feeder bin when the
cut-sheet feeder is installed.
Tear Off/Bin Both flash when continuous paper is in the
lights tear-off position.
Both off when continuous paper is not in the
tear-off position or when bin 1 of the optional
cut-sheet feeder is selected.
Left light is on when Card mode is selected.
Right light is on when bin 2 of the optional
cut-sheet feeder is selected.
5
Menu When you press the Pitch and Tear Off/Bin
buttons at the same time, the printer enters
the default setting mode. See "Changing the
Default Settings" on page 14.
6 Set In default setting mode, you can press the
Tear Off/Bin button to select a value.
7 Load/Eject button Loads a single sheet of paper.
Ejects a single sheet of paper.
Loads continuous paper from the standby
position.
Feeds continuous paper backward to the
standby position if a sheet is loaded.
8 Micro Adjust When you hold down the Pause button for
three seconds, the printer enters the Micro
Adjust mode. In this mode, you can press the
LF/FF
the top-of-form or tear-off position. See
"Using the Micro Adjust Function" on
page 11.
D U
and Load/Eject buttons to adjust
9 LF/FF button
10 Pause light
11 Pause button
12 Paper Out light
Lock function
Power-on Functions
The table below summarizes the power-on functions available
through the control panel. To perform the function on the
right, hold down the button(s) on the left while you turn on the
printer.
Control panel button
Load/Eject
LF/FF
Load/Eject + LF/FF
Load/Eject + LF/FF + Pause
Pause
Load/Eject + Pause
LF/FF + Pause
Font + Pitch
Pitch + Pause
Font + Tear Off/Bin
Tear Off/Bin + Pause
Tear Off/Bin + Load/Eject
Font + Pitch + Tear Off/Bin
6/03
EPSON FX-890/FX-2190
Feeds paper line by line when pressed
quickly.
Ejects a single sheet or advances continuous
paper to the next top-of-form position when
held down.
On when the printer is paused.
Flashes when the printer is in Micro Adjust
mode.
Stops printing temporarily, and resumes
printing when pressed again.
When held down for three seconds, enters
the Micro Adjust mode. When pressed again,
exits the Micro Adjust mode.
On when no paper is loaded in the selected
paper source or paper is not loaded correctly.
Flashes when paper has not been fully
ejected or paper is jammed.
When Lock-out mode is on, the Paper Out
and Pause lights flash if a locked button is
pressed. See the Reference Guide for more
information.
Function
NLQ self test
Draft self test
Data (Hex) dump
EEPROM reset
Bidirectional adjustment mode
Control panel Lock-out mode (on/off)
Default settings for control panel
Lock-out mode
Quiet mode
Copy mode
Default setting, simple mode
Okidata ML 320T/321T mode
Reset the Driving Line count for ribbon
change timing
Program reload mode
EPSON FX-890/FX-2190 7
-