Serene UA-45 User Manual

UA-45
Thank you for selecting the UA-45 phone amplifier. This unique
amplifier is compatible with virtually any modular connected phone
system. It enhances the clarity and increases incoming volume (up
to 170 times) for louder and clearer conversations. UA-45 comes
with these items:
U n i v e r s a l
P h o n e A m p l i f i e r
Installation & Operation:
1. Install a 9-volt battery (not included) and connect the UA-45 to your tele-
phone handset as shown. Use only the provided "short cord" to connect
UA-40 to the phone base. (Note: Ignore the ON /OFF indicator while doing
any switch setting. It is not relevant at this time.) For your safety, always dis-
connect UA-45from the phone base before replacing its battery. Use a coin
to ply open the battery door.
2. Set Volume control to its mid-point. Set Tone Control Switch to Position 2.
Volume Control
3. Setting the Compatibility Switch: There are 7 positions on this switch. Posi-
tions 1 to 6 are for compatibility setting use. Position 7 is a "by-pass" position
and is not for normal setting use. Position 7 offers no amplification and should
only be used in case of emergency when there is a total power outage.
A. Set Compatibility switch to Position 1 (Note: This is the most popular setting and is used
by most phones. Ignore ON / OFF indicator status while setting this switch. It is not
relevant at this time.)
B. Lift up the handset and verify you can hear a clear dial tone.
C. If there is no clear dial tone, hang up the handset and move the Compatibility switch to
the next position and repeat Step B.
D. If you do get a clear dial tone, verify the dial tone loudness can be changed by rotating
the volume control. If there is change in dial tone loudness, go to Step F.
E. If the dial tone loudness can not be changed by rotating the volume control, hang-up the
handset and move the Compatibility switch over to the next position. Repeat Step B.
F. Use the telephone keypad to make a call and verify you can hear each other.
G. If you can hear each other, then the present Compatibility switch setting is the correct
one and you are done. Record this switch setting for future reference. Go to Step 4.
H. If not, try the next Compatibility switch position until you can hear each other clearly.
(Note: Feel free to experiment with any switching setting.)
4. While talking on the phone, verify you can vary the handset volume by
rotating the volume control on the amplifier. (Caution: Lower the volume
control if you notice there is squeal sound in the handset).
This equipment complies with Part 68 of the FCC Rules. On the equipment is a label that contains, among other information, the
FCC registration number and ringer equivalence number (REN) for this equipment. If requested; this information must be provided to your
telephone company.
This equipment uses the following Universal Service Order Codes ("USOC") jacks: RJ-11. Connection to the telephone network should be
made by using standard modular telephone jack type RJ11.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when
your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five
(5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone
company to determine the maximum REN for your calling area.
If your telephone equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If pos-
sible, they will notify you in advance. But if advance notice is not practical, you will be notified as soon as possible. You will be informed of
your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of
your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.
In the event this equipment should fail to operate properly, disconnect the unit from the telephone line. Try using another FCC approved tele-
phone in the same telephone jack. If the trouble persists, call the telephone company repair service bureau.
If the trouble does not persist and appears to be with this unit, disconnect the unit from the telephone line and discontinue use of the unit until
it is repaired. For repair or warranty information, please contact Serene Innovations, Inc. at 562- 407 5400. Please note that the telephone
company may ask that you disconnect this equipment from the telephone network until the problem has been corrected or until you're sure that
the equipment is not malfunctioning.
There are no user serviceable parts in this equipment.
Serene Innovations, Inc.
5. While on the phone, try different Tone control settings to find the one with
the best incoming sound clarity. Lower the volume if you notice a squeal-
ing sound in the handset. Keep this setting for all future calls. You do not
need to change this tone setting again. Record this tone setting for future
reference.
6. Press and hold the BOOST button down. Verify the incoming voice be-
comes louder and the BOOST LED is on. You must release this button
when talking because your voice is muted if this button is held down.
Boost button
Tone Control
7. The ON / OFF indicator light should be on while the phone is in use. It
will go off in 8-15 seconds after going on-hook (or if there is no sound /
voice for 8-15 seconds).
8. During normal usage, a 9-volt alkaline battery may last 6-12 months.
Please replace the battery if the ON / OFF indicator becomes dim or if
the receiver sound is distorted.
9. An optional 9-volt DC adapter (not included) may be installed at this
time. This adapter provides normal operating power while the battery
Compatibility
serves as a back-up in case of power outage. The battery should be
Switch
changed once every two years or sooner if you notice the ON / OFF
indicator failed to come on during power outage.
To Phone base
Questions?
1. ON / OFF indicator is dim or does not ON: Replace the battery.
2. Can not hear dial tone or can not hear each other: Make sure the Com-
patibility switch is at the proper setting. If necessary, repeat A to D of
installation Step 3 above.
3. There is a loud squealing sound in my handset: The volume or tone is set
too high, lower volume or tone setting to stop the noise.
13421 Pumice Street Norwalk, CA 90650
Feature Identification:
1.
6.
5.
Tone Control
On-Off Indicator
Jack for optional DC adapter
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
Contact the state public utility commission, public service commission for information.
If your home has specialty wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable
your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Modification: Any modification not expressly approved by the manufacturer of this device could void the user's authority to operate the
device.
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunica-
tions network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance
with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal
metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspections authority, or
electrician, as appropriate. The REN for this amplified telephone as stated on the IC regulatory label located on the bottom of the product is
REN # 0.9B
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to
the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Tel: 562 407-541
2.
3.
7.
4.
1. Rotary volume 6. Boost Button and LED
2. ON / OFF Indicator 7. Jack to phone
3. Compatibility Switch 8. Jack for optional DC adapter
4. Tone Control Switch 9. Battery cover
5. Handset Jack
IMPORTANT SAFETY INSTRUCTIONS
WARNING – When using telephone equipment or electric appliances, basic
precautions should always be followed to reduce the risk of fire, electrical
shock and injury to persons, including the following:
1. Read all the instructions before using the appliance.
2. To reduce the risk of injury, close supervision is necessary when an appli-
ance is used near children.
3. Do not contact moving parts or any exposed metal surface.
4. Only use attachments recommended or sold by the manufacturer.
5. Do not use outdoors. Do not use near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
6. To disconnect, turn all controls to the off position, then remove plug from
outlet.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Unplug from outlet when not in use and before servicing or cleaning.
9. Do not operate any appliance with a damaged cord or plug, or after the
appliance malfunctions or is dropped or damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair,
or electrical or mechanical adjustment.
10. Use only the power cord and batteries indicated in the manual. Do not
dispose of batteries in fire. They may explode. Check local codes for
possible special disposal instructions.
11. Plug any power adapter to the socket-outlet that near the equipment and
should be easily accessible.
12. Avoid using any telephone product during an electrical storm. There may
be a remote risk of electric shock from lightning.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
"SAVE THESE INSTRUCTIONS"
Specifications:
Power source 9 volt alkaline battery (Not
Included)
Battery consumption 10 ma typical; automatic shut-off if
there is no voice
Battery life 6-12 months depending on usage
Amplification without Boost 30 dB
Amplification with Boost 45 dB
Auto shut off time (to save 8-15 seconds if no sound or voice
battery)
Compatibility switch (6 positions) + a "by-pass" position
Indicators ON / OFF, and BOOST
Controls Volume, BOOST, Tone Control,
Compatibility
Optional AC adapter 9 vdc. 200 ma (not provided)
Operating temperature 0 to 45 degree C
Storage temperature -20 to 50 degree C
Warranty Service Information:
UA-45 comes with one-year limited warranty. We warrant during this warranty period,
from the date of purchase, to the original consumer, UA-45 to be free from defects in
materials and workmanship under intended home use. In the event that UA-45 fails to
function properly within one year of original purchase due to defects in materials or
workmanship, return the unit (freight prepaid) with proof of purchase (sales receipt or
packing slip, no exceptions) to Serene Innovations. Serene Innovations will either repair
or replace the unit (with a refurbished unit or unit of equal condition) and return it to you
(using UPS/USPS ground shipping) at no cost to you if the unit is returned within 30
days of purchase. If the unit is returned after 30days of purchase but within the warranty
period, there will be a warranty handling charge of $9.95 for each return.
This warranty does not apply to any product that has been accidentally damaged,
abused, misused or negligent, used on electrical frequency or voltage other than marked
on product and/or described in manual. Defects or errors caused by unauthorized altera-
tions, repairs, and/or tampering are also not covered by this warranty.
This Warranty gives you specific legal rights, and you may also have other legal rights
that vary from states to states.
If a defect covered by this warranty should occur, promptly contact a Customer Care
Representative by phone or log onto www.sereneinnovations.com to obtain a Return
Authorization Number (RAN) and shipping instructions before shipping the product to
us. Any shipment without a RAN will not be accepted and will be returned to you at your
expense. Any authorized returned product must be accompanied with proof of purchase
and a brief explanation of the problem.
For out of warranty repaired and service, please contact our Customer Care Department
for directions.
8.
9.
Folding line