Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung FlexDry DVE60A9900 Series
Summary of Contents for Samsung FlexDry DVE60A9900 Series
- Page 1 FlexDry™ User manual DVE(G)60A9900* Untitled-1 1 2021-05-10 4:21:25...
-
Page 2: Table Of Contents
Contents Safety information What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING Important safety precautions Warnings Cautions Regulatory notice FCC Notice IC Notice Open Source Announcement Installation requirements Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements... - Page 3 Operations Control panel Operating a cycle Cycle overview Options System functions Special features Cycle chart Drying guide Maintenance General cleaning and maintenance instructions Upper dryer Lower dryer Troubleshooting Checkpoints Information codes Specifications Fabric care chart Protecting the environment Specification sheet English 3 Untitled-1 3 2021-05-10...
-
Page 4: Safety Information
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. -
Page 5: California Proposition 65 Warning
WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. -
Page 6: Important Safety Precautions
Safety information Important safety precautions WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. - Page 7 18. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 19. Do not insert your hand under the dryer. This may result in injury. 20. Take care that children’s fingers are not caught in the door when closing it. This may result in injury.
-
Page 8: Warnings
Safety information WARNING - What to do if you smell gas: • Do not try to light any appliance. • Do not turn on the appliance. • Do not touch any electrical switch. • Do not use any phone in your building. •... - Page 9 • Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product. • Clean the lint screen before or after each load. •...
-
Page 10: Regulatory Notice
Regulatory notice FCC Notice CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. -
Page 11: Ic Notice
Unintentional emitter per FCC Part 15 Product type : Clothes Dryers Model : DVE(G)60A9900* Responsible Party – U.S. Contact Information Samsung Electronics America, Inc. QA Lab America 19 Chapin Rd. Building D Pine Brook NJ 07058 Tel: 1-973-808-6375 Fax: 1-973-808-63 IC Notice The term “IC”... -
Page 12: Open Source Announcement
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name. -
Page 13: Installation Requirements
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. - Page 14 Installation requirements Alcove or closet installations WARNING • The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet. • No other fuel-burning appliance should be installed in the same closet as the dryer. •...
- Page 15 Side by side installation 1 in. (25 mm) 32.5 in. (825 mm) 27 in. (686 mm) 2 in. (50 mm) 21 in. (533 mm) 5.9 in. (150 mm) 61 in. (1550 mm) English 15 Untitled-1 15 2021-05-10 4:21:27...
-
Page 16: Ducting Requirements
Installation requirements Ducting requirements Use only for short-run Recommended installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° elbows Rigid Rigid 80 ft. (24.4 m) 74 ft. (22.6 m) 68 ft. (20.7 m) 62 ft. (18.9 m) 57 ft. -
Page 17: Exhausting Requirements
Exhausting requirements The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. -
Page 18: Gas Requirements
Installation requirements Gas requirements WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision (for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1 (for Canada). -
Page 19: Electrical Requirements
Electrical requirements The wiring diagram is located on the plate under the control panel or rear frame. WARNING • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. - Page 20 Installation requirements Electrical connections Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required.
-
Page 21: Installation
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer. 01 Top door 02 Control panel... - Page 22 Installation Accessories (supplied) Y-connector Water hose (Canadian elec. Short water hose models only) Flexible rack Dryer-sheet case Accessories (not supplied) You must purchase these items at a local service center. Pedestal English Untitled-1 22 2021-05-10 4:21:29...
- Page 23 Tools needed for installation Pliers Cutting knife Pipe wrench Nut screwdriver Level (gas models only) Phillips Duct tape Wrench LPG-safe screwdriver compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
-
Page 24: Step-By-Step Installation
Installation Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the doors before completing the product installation. If you remove the protective film before the installation is complete, the doors may get scratched or damaged during installation. - Page 25 STEP 3 Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 19. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block.
- Page 26 Installation 4-wire system 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
- Page 27 STEP 4 Connect the water hose (applicable models only) The dryer must be connected to a cold water tap using the provided water hoses. 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose.
- Page 28 Installation Using the short hose as an extension 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight.
- Page 29 STEP 5 Level the dryer To ensure optimal performance, the dryer must be level. Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling legs (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
- Page 30 Installation STEP 6 Power on (for gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7. STEP 7 Final Check When installation is complete, confirm that: •...
-
Page 31: Vent Blockage Test
Vent blockage test After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test function must run when the dryer is cool. - Page 32 Installation Installation check codes Check code Meaning Solution No problems Vent condition is good. detected 1. Clean the lint filter. Over 80 % of the vent is clogged. 2. Check your vent condition. (Refer to Vent is nearly the “Ducting requirements” section) (This may lead to poor drying clogged performance or cause malfunction)
-
Page 33: Exhaust Ducting Guide
Exhaust ducting guide Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. - Page 34 Installation 6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder. 8. Re-insert the two screws that held the lever holder into the same screw holes, and then tighten.
- Page 35 10. Insert the screw you just removed into the other screw hole on the back of the door hinge, and then tighten. 11. Place the door on the other side, and then reattach it to the dryer. NOTE Insert the head of the screw on the back of the hinge into the hole above the cut out in the frame, and then slide the door hinge down until it stops.
-
Page 36: Before You Start
Before you start Here are a few things you should know before starting your dryer. Initial setup • When you turn on your dryer for the first time, the screen shows the initial setup process. Follow the on-screen instructions to complete it. •... -
Page 37: Sort And Load
Sort and load • Put one wash load in the dryer at a time. • Do not mix heavy and lightweight items together. • To improve drying efficiency for one or two items, add a dry towel to the load. •... -
Page 38: Rack Guidelines
Before you start Rack guidelines Flexible rack The flexible rack is designed to dry delicate items that are not suitable for or cannot be dried in the lower dryer. To use the flexible rack 1. Locate the rack supports (x4) in each corner of the upper dryer. -
Page 39: Rack Dry (Applicable Models Only)
Remove the drying rack from its packaging and store the rack for later use. If a drying rack is not provided, you can purchase it at a local Samsung service center. (Part Code : DC93- 00374G) To use the drying rack, follow these steps: 1. -
Page 40: Operations
Operations This FlexDry™ dryer features the upper dryer and the lower dryer for your convenience. The upper dryer is a top load dryer that is designed to dry relatively small loads while the lower dryer is a drum loader you can use to dry normal or relatively heavy loads. - Page 41 You can start or pause the operation. • The upper button controls the upper dryer, and the lower button controls the 04 Start/Pause lower dryer. • Tap and hold the button to start the operation. • During the operation, tap the button to pause. The display shows the current cycle, estimated time remaining, cycle options, and 05 Display other useful or alert messages.
-
Page 42: Operating A Cycle
Operations Icon description Wi-Fi This icon indicates that the dryer is connected to Wi-Fi. This icon indicates that Smart Control is on. For more information on Smart Control “Smart Control”, see page 51. This icon indicates that Child Lock is on. Child Lock For more information on “Child Lock”, see page 48. -
Page 43: Cycle Overview
Cycle overview NOTE Other cycles can be used after adding them to your cycle list using the My Cycles function. For more information, see the “My Cycles” section on page 47. Upper dryer Cycle Description Blouses For synthetic blouses and blouses with accessories (ornaments) For washable wool or wool-blended sweaters, cotton or cotton-blended Sweaters sweaters, and knitted cardigans... - Page 44 Operations Cycle Description Bedding For bulky items such as blankets, sheets, comforters, and light duvets. For exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets, and other performance clothing. Thick fabrics like a Activewear zipper or velcro closure of a jacket, or training socks may not be completely dried.
-
Page 45: Options
Options Using Options 1. Tap UPPER or LOWER to select the upper or lower dryer. 2. Tap Options. 3. Turn the Navigation dial to select the desired additional function. 4. Tap OK to change the selected function’s settings or start the function. NOTE •... - Page 46 Operations Super Speed Super Speed increases the fan speed to shorten the drying time. This option is available for the Blouses, Undergarments and Accessories cycles. 1. Tap UPPER. This function is not available for the lower dryer. 2. Tap Options. 3.
- Page 47 AntiStatic Reduces static electricity that occurs from clothing friction. This is done by spraying steam in a later stage of the drying cycle. The AntiStatic function is only available with Normal, Heavy Duty, Perm Press, Delicates, and Time Dry. In the Normal, Heavy Duty, Delicates, and Perm Press cycles, you can use this function if the dryness setting is 3 or higher.
- Page 48 Operations Drum Light You can turn the drum light on or off. 1. Tap LOWER. This function is not available for the upper dryer. 2. Tap Options. 3. Turn the Navigation dial to select Drum Light, and then tap OK. 4.
-
Page 49: System Functions
System functions Using System Functions 01 * * Tap and hold 3 seconds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial and select the desired system function, and then tap OK. 3. Tap OK to change the selected function’s settings or start the function. NOTE •... - Page 50 Operations Alarm You can enable/disable alarm sounds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial to select Alarm, and then tap OK. 3. Tap OK to select On or Off. The default setting is On. NOTE The setting remains unchanged even if you restart the dryer.
-
Page 51: Special Features
Special features Smart Control You can connect to the SmartThings app and control your dryer remotely. (Smart Control for electric model, Smart Monitor for gas model) Connecting your dryer • Download and open the SmartThings app on your mobile device •... - Page 52 • This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app with a search term of “SmartThings”. Download and install the app on your device.
-
Page 53: Cycle Chart
Cycle chart Upper dryer • The drying time depends on the load and the item type. To shorten the drying time, use Super Speed. • For manual-wash items, use a towel to remove moisture from the items before drying. • To reduce the drying time of the items that are machine-washable, set the spinning option on your washer to high to remove as much moisture as possible. - Page 54 Operations NOTE : factory setting, : can be selected Options Cycle Time Air Fluff Super Speed Blouses Sweaters Undergarments Accessories CAUTION Clothing with accessories or hooks may get stuck in the mesh of the rack.
- Page 55 Not Recommended for the upper dryer Do not dry shoes, bags, down/fur products, rugs, carpets, or bulky items in the upper dryer. Do not dry shoes, bags, down/fur products, rugs, carpets, or bulky items in the upper dryer. English 55 Untitled-1 55 2021-05-10 4:21:40...
- Page 56 Operations Lower dryer NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about full.
- Page 57 NOTE : factory setting, : can be selected Options Functions Cycle Time (Temp. Control) AntiStatic Damp Alert Wrinkle Prevent Eco Dry Normal Medium, level 4 High, level 5 Time Dry (Adjustable) Heavy Duty High, level 5...
-
Page 58: Drying Guide
Operations Drying guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Lower dryer Items Description Follow the care label instructions or dry using Bedding. Bedspreads &... -
Page 59: Maintenance
Maintenance Keep your FlexDry™ dryer clean to prevent decreased performance and to lengthen its life. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. -
Page 60: Upper Dryer
Maintenance Upper dryer Flexible rack • If you use the flexible rack, make sure to clean the rack after every use so that it is readily available for future use. • Clean the rack with neutral cleaning agents and running water. Upper recesses •... -
Page 61: Lower Dryer
Lower dryer Stainless steel drum • Clean the drum after every use. • To clean the stainless steel drum, use a damp cloth with a mild, non-abrasive cleaner suitable for easily marred surfaces. Remove cleaner residue and dry with a clean cloth. Drying rack •... -
Page 62: Troubleshooting
Troubleshooting Checkpoints If you encounter a problem with the dryer, first check the table below and try the suggestions. Problem Action • Make sure the dryer is plugged in. • Make sure the door is properly closed. • Check the fuse or reset the circuit breaker. •... - Page 63 Problem Action • Look for coins, loose buttons, nails, and other objects and remove them immediately. • Check the lint filter. Remove any items stuck inside the lint filter. • Make sure the dryer is level and standing firmly on the floor. The dryer is too loud.
-
Page 64: Information Codes
• If this information code remains, contact a Samsung service center. Incorrect door switch. Contact a Samsung service center. If any information code keeps appearing on the display, contact a Samsung service center. English Untitled-1 64 2021-05-10 4:21:41... -
Page 65: Specifications
Specifications Fabric care chart The following symbols provide garment care Normal direction. The clothing care labels include symbols Permanent press/Wrinkle resistant/ for drying, bleaching, ironing, and dry cleaning. Wrinkle control The use of symbols ensures consistency among garment manufacturers of domestic and imported Gentle/Delicates items. -
Page 66: Protecting The Environment
Specifications Warning symbols for laundering Dry-clean Do not wash Dry-clean Do not wring Do not dry-clean Do not bleach Line dry / Hang to dry Do not tumble dry Drip dry No steam (added to iron) Dry flat Do not iron Protecting the environment This appliance is manufactured from recyclable materials. - Page 67 Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center to receive warranty service.
- Page 68 LIMITED WARRANTY (U.S.A.) Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues. EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW.
- Page 69 Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability within the Canada.
- Page 70 (English) www.samsung.com/ca_fr/support (French) Visits by a Service Engineer to explain functions, maintenance, or installation is not covered by warranty. Please contact the Samsung call center at the number above for help with any of these issues. English Untitled-1 70...
- Page 71 Memo Untitled-1 71 2021-05-10 4:21:45...
- Page 72 If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support www.samsung.com/ca/support (English) CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca_fr/support (French) DC68-03382E-00 Untitled-1 72...