Page 1
SERVICE MANUAL 9090X / 9090X GE / 9090X H / 9090X O / 9090X COFFEE / 9090X OLIVE PLUS / 9090X OLIVE PLUS GE Grape Harvester Part number 47914333 edition English July 2015...
Page 2
F4HE9687 9090X COFFEE North America F4HE9687 North America F4HE9687 9090X GE 9090X H North America F4HE9687 9090X O North America F4HE9687 9090X OLIVE PLUS North America F4HE9687 9090X OLIVE PLUS GE North America F4HE9687 47914333 22/07/2015 Find manuals at https://best-manuals.com...
Page 7
9000 X IMPORTANT INFORMATION All repair and maintenance operations described in this manual must be carried out exclusively by the New Holland Service network, strictly complying with the instructions provided and using specific tools as required. Any operator who carries out the operations specified in this document without complying strictly with the instructions provided shall be personally liable for the damages that may result.
Page 8
INTRODUCTION Foreword 9000 X Technical Information This information in this manual has been structured using a unique coding environment. This is the way in which technical information is created, stored and retrieved in the Technical Information Database. The location (on the machine) has been coded using SAP coding to align locations with the warranty system.
Page 9
INTRODUCTION Sections Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a letter number etc. The amount of Sections included in the manual will depend on the type and function of the machine that the manual is written for.
Page 10
INTRODUCTION This manual contains these sections. Contents INTRODUCTION Engine Rear axle system Hydrostatic drive Brakes and controls Hydraulic systems Frames and ballasting Direction Electrical systems Grape harvester shaking Product feeding Cleaning Secondary cleaning / Destemmer Crop storage / Unloading Accessories Your manual contains these Sections.
Page 11
INTRODUCTION Information Units and Information Search Each chapter is composed of information units. The coding is not included in the Information Unit title. Page Header and Footer The page header will contain the following references: • Section and Chapter description The page footer will contain the following references.
INTRODUCTION Basic instructions 9000 X SHIMMING For each adjustment operation, select adjusting shims, individually measure using a micrometer, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, and do not rely on the rated value indicated on each shim.
Page 13
INTRODUCTION PROTECTING THE ELECTRONIC/ELECTRICAL SYSTEMS DURING CHARGING OR WELD- To avoid damaging the electronic/electrical systems, always follow the safety instructions below: 1. Never make or break any of the charging circuit connections, including the battery connections, when the engine is running. 2.
Page 14
Only genuine spare parts guarantee the same quality, duration, and safety of original parts, as they are the same parts installed during standard manufacturing operations. Only New Holland genuine spare parts can offer this guarantee. When ordering spare parts, always provide the following information: •...
INTRODUCTION Special tools 9000 X - List of special tools for the entire machine - Hot air blower to weld conveyor belts, Ref.: 298207. COIL11GRH036A0A Manual pliers to fit rivets to baskets. Ref. : 298201. COIL11GRH038A0A Pneumatic pliers to fit rivets to baskets. Ref. : 298202. COIL11GRH037A0A 47914333 22/07/2015...
Page 18
INTRODUCTION Tool to screw the lift cylinder parachute valves onto the front of the machine. Ref: 298228. COIL11GRH039A0A Tool to fit the wheel motor brake pistons. Ref: 298229. H and h = 10 mm (0.394 in). D1 = 215 mm (8.465 in). d1 = 205 mm (8.071 in).
Page 19
INTRODUCTION Norias from ground washing position control cable. Ref: 944033078. COIL11GRH043A0A Clamp to remove complete rotors from the destemmers. A = 475 mm (18.701 in). B and C = 10 mm (0.394 in). D = Ø: 26 - 34 mm (1.024 - 1.339 in). E = Radius 21 mm (0.827 in).
Page 20
INTRODUCTION Tool for levelling the Norias rails. Ref: 944029815. COIL11GRH047A0A Tool to remove the pins in the round "Deutsch" harness connector of harvesting equipment Kit ref.: 380 000 350 comprising: - 80 900 370 for pin Ø 8 mm white - - 80 900 371 for pin Ø...
Page 21
INTRODUCTION Tool for removing and refitting the front struts. ITEMS DESCRIPTIONS DIMENSIONS QUAN- MATERIAL TITY Tube A = 193.7 mm (7.626 in) is the internal diameter of the tube. B = 650 mm (25.6 in). C = 5.4 mm (0.213 in) is the thickness of the tube. Threaded rod A = 1200 mm (47.2 in).
INTRODUCTION Conversion factors 9000 X Linear 1 mm 0.03937 in 1 in 25.4 mm 1 Km 0.6214 miles 1 mile 1.6093 km 3.281 ft 1 ft 0.3048 m Surface 1 ha 2.471 acre 1 acre 0.4047 ha Volume 1 litre 0.0063 barrel 1 barrel 158.987 litre...
INTRODUCTION Product identification 9000 X EXPLANATION OF MACHINE SERIAL NUMBERS Example: No. HAG 00 --- E 00 001 001 HAG 00 --- E 00 001 001: the first three figures is a code for Coëx production (France) HAG 00 --- E 00 001 001: free areas are marked 00 HAG 00 --- E 00 001 001: these three figures relate to the machine type 9060L = --- HAG 00 --- .
Page 25
SERVICE MANUAL Rear axle system 9090X COFFEE , 9090X GE , 9090X H , 9090X OLIVE PLUS GE , 9090X OLIVE PLUS , 9090X O , 9090X 47914333 22/07/2015...
Page 27
Rear axle system - 27 Powered rear axle - 100 9090X COFFEE , 9090X GE , 9090X H , 9090X OLIVE PLUS GE , 9090X OLIVE PLUS , 9090X O , 9090X 47914333 22/07/2015 27.1 [27.100] / 1...
Page 28
Contents Rear axle system - 27 Powered rear axle - 100 SERVICE Rear axle Transform - Changing the rear track - (*) ............3 (*) See content for specific models 47914333 22/07/2015 27.1 [27.100] / 2...
Page 29
Rear axle system - Powered rear axle Rear axle - Transform - Changing the rear track - 9000 X NOTE: To change the rear track of the machine by 160 mm (6.3 in), you must turn over the wheel arm fastening bearings.
Page 30
Rear axle system - Powered rear axle 6. Remove the spring retaining rings (7) and pull out the bearings (5). COIL11GRH022A0B 7. Fit the bearings (8) onto the wheel arms at the required track width. • Position A = wide track. •...
Page 31
Rear axle system - Powered rear axle 14. Adjust the side stops of the harvesting equipment. • The diagram shows how the stop is fitted when the machine track is in the wide position. The spacer ring (10) is fitted inside the bracket. •...
Page 32
Index Rear axle system - 27 Powered rear axle - 100 Rear axle - Transform - Changing the rear track - (*) ........... . 3 (*) See content for specific models 47914333 22/07/2015 27.1 [27.100] / 6...
Page 34
All rights reserved. No part of the text or illustrations of this publication may be reproduced. NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment at any time without notices is reserved.
Page 35
SERVICE MANUAL Hydrostatic drive 9090X COFFEE , 9090X GE , 9090X H , 9090X OLIVE PLUS GE , 9090X OLIVE PLUS , 9090X O , 9090X 47914333 22/07/2015...
Page 36
Contents Hydrostatic drive - 29 [29.300] Rear hydrostatic transmission............29.1 [29.218] Pump and motor components.
Page 37
Hydrostatic drive - 29 Rear hydrostatic transmission - 300 9090X COFFEE , 9090X GE , 9090X H , 9090X OLIVE PLUS GE , 9090X OLIVE PLUS , 9090X O , 9090X 47914333 22/07/2015 29.1 [29.300] / 1...
Page 38
Contents Hydrostatic drive - 29 Rear hydrostatic transmission - 300 FUNCTIONAL DATA Rear hydrostatic transmission Hydraulic schema (*) ............... 4 (*) See content for specific models 47914333 22/07/2015 29.1 [29.300] / 2...
Page 45
Hydrostatic drive - 29 Pump and motor components - 218 9090X COFFEE , 9090X GE , 9090X H , 9090X OLIVE PLUS GE , 9090X OLIVE PLUS , 9090X O , 9090X 47914333 22/07/2015 29.2 [29.218] / 1...
Page 46
Contents Hydrostatic drive - 29 Pump and motor components - 218 SERVICE Motor Remove - Rear wheel motor - (*) ............. 3 Install - Rear wheel motor - (*) .
Page 47
Hydrostatic drive - Pump and motor components Motor - Remove - Rear wheel motor - 9000 X NOTE: When removing the hydraulic piping, have a suitable container readily available to capture any residual hy- draulic oil. 1. Remove the corresponding rear wheel. To do this: •...
Page 48
Hydrostatic drive - Pump and motor components 5. Remove the fixing screws (6) and take out the motor. COIL10GRH460A0B ATTENTION: The component weighs approximately 160 kg (352.7 lb). Install a suitable lifting device. 6. Remove the hose installations from the motor and plug them.
Page 49
1. Check that the motor is installed on the correct side of the machine. These motors have a specific direction of rotation. To ascertain the direction of rotation, check the part number NEW HOLLAND on the manufacturer's plate for the motor: • 87672923 — right-hand motor.
Page 50
Hydrostatic drive - Pump and motor components 7. Adjust the speed sensor. To do this: • Press the target (disc) against the hub using the wheel nuts. • Position the bracket between (8) and 3 mm (0.118 in) from the ends of the target (disc) (10). •...
Page 51
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...