Page 1: Table Of Contents
2007 Cadillac SRX Owner Manual Seats and Restraint Systems ... 7 Front Seats ... 9 Rear Seats ... 18 Safety Belts ... 22 Child Restraints ... 43 Airbag System ... 70 Restraint System Check Features and Controls ... 91 Keys ...
Page 2 Service and Appearance Care ... 343 Service ... 346 Fuel ... 349 Checking Things Under the Hood All-Wheel Drive ... 392 Rear Axle ... 394 Front Axle ... 395 Bulb Replacement ... 396 Windshield Wiper Blade Replacement Tires ... 398 Appearance Care ...
Page 3: Canadian Owners
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest and Wreath, and the name SRX are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes to the product after that time without notice.
Page 4: How To Use This Manual
How to Use This Manual Many people read the owner manual from beginning to end when they ﬁrst receive their new vehicle. If this is done, it can help you learn about the features and controls for the vehicle. Pictures and words work together in the owner manual to explain things.
Page 5: Vehicle Symbols
Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 6 These are some examples of symbols that may be found on the vehicle:...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ... 9 Manual Seats ... 9 Power Seats ... 10 Power Lumbar ... 10 Heated Seats ... 11 Memory Seat and Mirrors ... 12 Reclining Seatbacks ... 14 Head Restraints ... 17 Rear Seats ... 18 Rear Seat Operation ...
Page 8 Section 1 Airbag System ... 70 Where Are the Airbags? ... 73 When Should an Airbag Inﬂate? ... 77 What Makes an Airbag Inﬂate? ... 79 How Does an Airbag Restrain? ... 79 What Will You See After an Airbag Inﬂates? ...
Page 9: Front Seats
Front Seats Manual Seats CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. Your vehicle may have manual seats.
Page 10: Power Seats
Power Seats If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. • Move the seat forward or rearward by sliding the horizontal control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down.
Page 11 To increase or decrease support, hold the control forward or rearward. Keep in mind that as your seating position changes, as it may during long trips, so should the position of your lumbar support. Adjust the seat as needed. Heated Seats Your vehicle may have heated front seats.
Page 12: Memory Seat And Mirrors
Memory Seat and Mirrors If your vehicle has the memory feature, you can program and recall memory settings for the driver’s seating and outside rearview mirror driving positions for up to two drivers. If your vehicle has the adjustable throttle and brake pedal feature, you can also program and recall memory settings for the throttle and brake pedal driving positions.
Page 13 Two personalized exit positions can also be programmed. Use the following steps to program exit positions: 1. Press memory seat button 1 or the button with the unlock symbol on the remote keyless entry transmitter with the number 1 on the back to recall the driving position.
Page 14: Reclining Seatbacks
Reclining Seatbacks Manual Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 15 To return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Page 16 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 17: Head Restraints
Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. The height of the front seat head restraints can be adjusted.
Page 18: Rear Seats
If the vehicle has third row seats, the head rests adjust like the front seat head restraints. The third row seat head rests can be removed from the seatback. To do this, press the button, located on the top of the seatback, and pull them out from the seatback.
Page 19 Entering or Exiting the Third Row Seat CAUTION: Be sure to return the seat to the passenger seating position when ﬁnished. Push and pull on the seat to make sure it is locked into place. Never use the third row seating position while the second row is folded, or folded and tumbled.
Page 20: Stowable Seat
Stowable Seat If your vehicle has a third row seat, it is a power folding seat. The head rests need to be removed before folding the third row seat. See Head Restraints on page 17 for instructions for removing the third row seat head rests.
Page 21 Before folding or unfolding the third row seat, all of the following conditions must be met: • The liftgate or passenger’s side rear door must be open. • The unlock button on either the remote keyless entry transmitter or the door must be pressed three times to enable the rear seat for two minutes, or the ignition must be in ON or ACCESSORY.
Page 22: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 23 In most states and in all Canadian provinces, the law says to wear safety belts. Here is why: They work. You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one.
Page 24 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 25 The person keeps going until stopped by or the instrument panel... something. In a real vehicle, it could be the windshield...
Page 26: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after an...
Page 27: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Page 28 3. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.
Page 29 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 30 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 31 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force at your abdomen.
Page 32 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen.
Page 33 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 34 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 35: Safety Belt Use During Pregnancy
To unlatch the belt, push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 36: Right Front Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 37 Rear passengers who are not safety belted can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. Lap-Shoulder Belt All rear seat positions have lap-shoulder belts. Here is how to wear one properly. 1.
Page 38 3. To make the lap part tight, pull up on the shoulder part. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt.
Page 39: Rear Safety Belt Comfort Guides
CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. To unlatch the belt, push the button on the buckle. Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children...
Page 40 Here is how to install the comfort guide to the shoulder belt. 1. Slide the guide off of its storage clip located on the seatback. 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt and insert the two edges of the belt into the slots of the guide.
Page 41 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 42: Safety Belt Pretensioners
Safety Belt Pretensioners Your vehicle has safety belt pretensioners for the driver and right front passenger. Although you cannot see them, they are part of the safety belt assembly. They help tighten the safety belts during the early stages of a moderate to severe frontal or near frontal crash if the threshold conditions for pretensioner activation are met.
Page 43: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 44 CAUTION: Never do this. Here two children are wearing the same belt. The belt cannot properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time.
Page 45 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 46: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 47 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for CAUTION: (Continued) CAUTION: (Continued) young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 48 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 49: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 50 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 51 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window.
Page 52 Securing an Add-on Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Make sure the child restraint is properly installed in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that restraint,...
Page 53: Where To Put The Restraint
Securing the Child Within the Child Restraint There are several systems for securing the child within the child restraint. One system, the three-point harness, has straps that come down over each of the infant’s shoulders and buckle together at the crotch. The ﬁve-point harness system has two shoulder straps, two hip straps, and a crotch strap.
Page 54 Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right...
Page 55: Lower Anchors And Tethers For Children (Latch)
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Page 56 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 57 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Second Row Each outboard seating position in the second row has exposed metal lower anchors in the crease between the seatback and the seat cushion. (Top Tether Anchor): To assist you in locating the top tether anchors,...
Page 58 There are two top tether anchors located on the side of the wheel well in the rear cargo area. There is another top tether anchor in the center of the rear cargo area. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 59 Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed.
Page 60 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been...
Page 61 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 62 If the position you are using has an adjustable head restraint and you are using a single tether, route the tether under the head restraint and in between the head restraint posts. 3. Push and pull the child restraint in different directions to be sure it is secure.
Page 63 CAUTION: In a crash, a child secured in a rear-facing child restraint in the center rear seating position could be injured by the vehicle’s armrest. To reduce this risk, the armrest should ﬁrst be secured with a special armrest retention strap. You can get this from your dealer.
Page 64 4. Pull the rest of the shoulder belt all the way 5. To tighten the belt, push down on the child out of the retractor to set the lock. restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 65: Securing A Child Restraint In The Right Front Seat Position
6. If your child restraint has a top tether, and the position that you are using has a top tether anchor, attach and tighten the top tether to the top tether anchor. Refer to the instructions that came with the child restraint and to Lower Anchors and Tethers for Children (LATCH) on page 55.
Page 66 A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 67 If you need to secure a forward-facing child restraint in the right front seat position, move the seat as far back as it will go before securing the forward-facing child restraint. See Manual Seats on page 9 or Power Seats on page 10. If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 55.
Page 68 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. Tilt the latch plate to adjust the belt if needed. 4.
Page 69 5. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt. 6.
Page 70: Airbag System
Airbag System Your vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger.
Page 71 CAUTION: Frontal airbags for the driver and right front passenger are designed to deploy in moderate to severe frontal and near frontal crashes. They are not designed to inﬂate in rollover, rear crashes, or in many side crashes. And, for some unrestrained occupants, frontal airbags may provide less protection in frontal crashes than more forceful airbags have provided in...
Page 72 CAUTION: Both frontal and side impact airbags inﬂate with great force, faster than the blink of an eye. If you are too close to an inﬂating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inﬂation before and during a crash.
Page 73: Where Are The Airbags
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 201 for more information.
Page 74 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. The driver’s seat-mounted side impact airbag is in the side of the driver’s seatback closest to the door.
Page 75 The right front passenger’s seat-mounted side impact airbag is in the side of the passenger’s seatback closest to the door. The roof-mounted side impact airbag for the driver and the passenger directly behind the driver is in the ceiling above the side windows.
Page 76 The roof-mounted side impact airbag for the front passenger and the passenger directly behind the front passenger is in the ceiling above the side windows. CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 77: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in...
Page 78 Frontal airbags may inﬂate at different crash speeds. For example: • If the vehicle hits a stationary object, the airbags could inﬂate at a different crash speed than if the vehicle hits a moving object. • If the vehicle hits an object that deforms, the airbags could inﬂate at a different crash speed than if the vehicle hits an object does not deform.
Page 79: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. In the case of a “rollover capable” roof-mounted side impact airbag, the sensing system detects that the vehicle is about to roll over.
Page 80 What Will You See After an Airbag Inﬂates? After frontal airbags and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-mounted side impact airbags may still be at least partially inﬂated minutes after the vehicle comes to rest.
Page 81: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 82 The passenger sensing system will turn off the right front passenger’s frontal airbag under certain conditions. The driver’s airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat.
Page 83 CAUTION: (Continued) guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. If you need to secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go.
Page 84 When the passenger sensing system has turned off the right front passenger’s frontal airbag, the off indicator will light and stay lit to remind you that the airbag is off. If a child restraint has been installed and the on indicator is lit, turn the vehicle off.
Page 85 Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and then enable the passenger’s airbag. CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 86 A thick layer of additional material, such as a blanket, or aftermarket equipment such as seat covers, seat heaters, and seat massagers, can affect how well the passenger sensing system operates. Remove any additional material from the seat cushion before reinstalling or securing the child restraint and before a small occupant, including a small adult, sits in the right front passenger’s seat.
Page 87: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. You do not want the system to inﬂate while someone is working on your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system.
Page 88 Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to the front or sides of the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 89: Restraint System Check
Restraint System Check Checking the Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 90: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary...
Page 91: Features And Controls
Section 2 Keys ... 93 Remote Keyless Entry (RKE) System ... 94 Remote Keyless Entry (RKE) System Operation ... 96 Doors and Locks ... 100 Door Locks ... 100 Central Door Unlocking System ... 101 Power Door Locks ... 101 Delayed Locking ...
Page 92 Section 2 Mirrors ... 134 Automatic Dimming Rearview Mirror ® with OnStar ... 134 Automatic Dimming Rearview Mirror ® with OnStar and Compass ... 134 Outside Power Heated Mirrors ... 137 Outside Automatic Dimming Mirror ... 138 Outside Curb View Assist Mirror ... 138 Outside Convex Mirror ...
Page 93: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and they could be seriously injured or killed if caught in the path of a closing...
Page 94: Remote Keyless Entry (Rke) System
If you ever lose your keys, your dealer will be able to assist you with obtaining replacements. In an emergency contact Cadillac Roadside ® Service . See Roadside Service on page 493 for more information.
Page 95: Operation
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 96: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation With this feature, you can lock and unlock the doors and liftgate, open and close the liftgate, and turn on your vehicle’s interior lamps from up to 65 feet (20 m) away using the Remote Keyless Entry (RKE) transmitter supplied with your vehicle.
Page 97 (Panic Alarm): Press and release this button to locate your vehicle. The turn signal lamps will ﬂash and the horn will sound three times. Press and hold this button for more than two seconds to activate the panic alarm. The turn signal lamps will ﬂash and the horn will sound repeatedly for 30 seconds.
Page 98 To replace the battery in the RKE transmitter do the following: 1. Use a ﬂat object with a thin edge into the notch, located below the trunk release button, and separate the bottom half from the top half of the transmitter. 2.
Page 99 To replace the battery in the RKE transmitter do the following: 1. Use a ﬂat object with a thin edge into the notch, located above the metal base, and separate the bottom half from the top half of the transmitter. 2.
Page 100: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 101: Central Door Unlocking System
There are several ways to lock and unlock your vehicle. Because your vehicle has the theft-deterrent system, you must unlock the doors from the outside with the key or Remote Keyless Entry (RKE) transmitter to avoid setting off the alarm. If the windows are down and the doors are locked, do not reach in to manually unlock the vehicle because you will set off the alarm.
Page 102: Delayed Locking
Delayed Locking With this feature, you can delay the actual locking of the doors. When the power door lock switch or the lock button on the remote keyless entry transmitter is pressed when the key is not in the ignition and the driver’s door is opened, a chime will sound three times indicating that delayed locking is active.
Page 103: Rear Door Security Locks
Rear Door Security Locks Your vehicle has rear door security locks that prevent passengers from opening the rear doors on your vehicle from the inside. The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them.
Page 104: Lockout Protection
Lockout Protection If you press the power door lock switch when the key is in the ignition and any door is open, all the doors will lock and only the driver’s door will unlock. If you close the doors, you can lock them using the remote keyless entry transmitter.
Page 105 Notice: If you open the liftgate without checking for overhead obstructions such as a garage door, you could break the liftgate or the liftgate glass. Always check to make sure the area above the liftgate is clear before opening it. To open and close the liftgate, press and hold the power liftgate button on the remote keyless entry transmitter (RKE) until the liftgate starts...
Page 106 If you shift the transmission out of PARK (P) while the power function is in progress, the liftgate power function will continue to completion. If you shift the transmission out of PARK (P) and accelerate before the power liftgate latches closed, the liftgate may reverse to the open position.
Page 107 Manual Liftgate Operation With the doors unlocked, the power liftgate can always be manually opened and closed. To open the liftgate, pull up on the handle on the outside of the liftgate. To close the liftgate, use the pull cup to lower the liftgate and close. The liftgate latch will power cinch to closed position.
Page 108: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 109: Power Windows
Power Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome from extreme heat in warm or hot weather and suffer permanent injuries or even death from heat stroke. Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly...
Page 110 Express-Down Window This feature is on all windows. Press the switch to the second position and release the switch to activate the express-down feature. To stop the window as it is lowering, press down or pull up brieﬂy on the switch again. Express-Up Window This feature is on all windows.
Page 111 Express Window Anti-Pinch Override CAUTION: If express override is activated, the window will not reverse automatically. You or others could be injured and the window could be damaged. Before you use express override, make sure that all people and obstructions are clear of the window path.
Page 112: Theft-Deterrent Systems
Sun Visors Swing down the primary visor to block out glare. It can also be detached from the center mount and moved to the side to block glare from that direction. The driver’s sunshade may also have buttons for a built-in garage door opener. See Universal Home Remote System (With Three Round LED) on page 143 or Universal Home Remote System (With One Triangular LED) on page 143...
Page 113 The theft-deterrent system will not arm if you lock the doors with a key, use the manual door lock or if the liftgate is ajar. It activates only if you use the RKE transmitter or the power door lock. To avoid activating the alarm by accident do the following: •...
Page 114: Pass-Key Iii+ Operation
® PASS-Key III+ ® The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 115 If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse, see Fuses and Circuit Breakers on page 455. If the engine still does not start with the other key, your vehicle needs service.
Page 116: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines for the ﬁrst 500 miles (805 km): • Do not drive at any one constant speed, fast or slow.
Page 117: Ignition Positions
Ignition Positions With the key in the ignition switch, you can turn the key to four different positions. Notice: If your key seems stuck in OFF and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard.
Page 118: Retained Accessory Power (Rap)
Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime will sound, when you open the driver’s door.
Page 119: Starting The Engine
Starting the Engine Place the transmission in the proper gear. Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position -- this is a safety feature. To restart when you are already moving, use NEUTRAL (N) only.
Page 120: Adjustable Throttle And Brake Pedal
2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or 18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds.
Page 121: Engine Coolant Heater
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 122: Automatic Transmission Operation
How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle.
Page 123 Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You must fully apply your regular brakes ﬁrst and then press the shift lever button before you can shift from PARK (P) when the ignition key is in ON.
Page 124 DRIVE (D): This position is for normal driving. It provides the best fuel economy for your vehicle. If you need more power for passing, and you are: • Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. •...
Page 125 2. To enter the DSC mode, press the shift lever forward to upshift or rearward to downshift. The DIC will show the requested gear range when moving the shift lever forward or rearward. See Driver Information Center (DIC) on page 214 While using the DSC feature, the vehicle will have ﬁrmer shifting and increased performance.
Page 126: Tow/Haul Mode
Tow/Haul Mode Your vehicle may be equipped with a Tow/Haul mode. The button is located on instrument panel under the climate controls. You should use this feature to assist when towing or hauling a heavy load. When Tow/Haul is activated the Tow/Haul symbol will illuminate on the instrument panel cluster.
Page 127: Parking Brake
Grade Braking Grade Braking assists when driving on a downhill grade. It maintains the vehicle’s speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle. This reduces wear on the brakes system and increases control of the vehicle. The system constantly monitors the vehicle’s speed, acceleration, throttle position, and whether the brake pedal is being pressed, and determines...
Page 128 To release the parking brake, pull the release lever located to the left of the steering wheel on the instrument panel. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts.
Page 129: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 130 Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 131: Shifting Out Of Park (P)
Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system. To shift out of PARK (P): 1. Apply the regular brake pedal. 2. Then press the shift lever button. 3. Move the shift lever to the desired gear. If you are still unable to shift out of PARK (P): 1.
Page 132: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • The exhaust system sounds strange or different. •...
Page 133: Running The Engine While Parked
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 134: Mirrors
Mirrors Automatic Dimming Rearview Mirror ® with OnStar The vehicle may have an automatic dimming inside rearview mirror with OnStar more information about OnStar System on page 139. (On/Off): The on/off button, located on the lower left side of the mirror, is used for the automatic dimming functions of the rearview mirror.
Page 135 Mirror Operation The automatic dimming feature comes on each time the vehicle is started. To turn the automatic dimming feature on or off, press the on/off or AUTO button. The indicator light will illuminate when this feature is on. Compass Operation Press the on/off button once to turn the compass on or off.
Page 136 To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2. Press and hold the on/off button until a zone number appears on the display. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number.
Page 137: Outside Power Heated Mirrors
Outside Power Heated Mirrors The power mirror controls are located on the driver’s door armrest and operate both outside rearview mirrors. • Press (A) to select the driver’s side mirror. The LED indicator will turn on to indicate that this mirror is selected. Then press the arrows located on the four-way control pad to adjust the mirror.
Page 138: Outside Automatic Dimming Mirror
Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs: • The mirrors are accidentally obstructed while folding. • They are accidentally manually folded/unfolded. • The mirrors will not stay in the unfolded position.
Page 139: Outside Convex Mirror
The driver can select either mirror, or both mirrors to be activated with this feature. Deselect both mirrors to turn off the automatic tilt feature. If further adjustment is needed after the mirror is tilted, the mirror controls can be used. See Outside Power Heated Mirrors on page 137 for more information.
Page 140 ® OnStar service is provided to you subject to the ® OnStar Terms and Conditions. You may ® cancel your OnStar service at any time by ® contacting OnStar as provided below. A complete ® OnStar Owners Guide and the OnStar and Conditions are included in the vehicle’s ®...
Page 141 Available Services included with Directions ® & Connections Plan • All Safe and Sound Plan Services • Driving Directions - Advisor delivered or ® OnStar Turn-by-Turn Navigation (If equipped) • RideAssist • Information and Convenience Services ® OnStar Hands-Free Calling ®...
Page 142 ® How OnStar Service Works In order to provide you with OnStar ® your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an ® OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys.
Page 143: Universal Home Remote System
Universal Home Remote System Universal Home Remote System (With Three Round LED) The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules.
Page 144: Universal Home Remote System Operation (With Three Round Led)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is CB2SAHL3.
Page 145 Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming.
Page 146 Programming Universal Home Remote — Fixed Code Fixed Code garage door openers are used for garage doors produced prior to 1996. Fixed code uses the same coded signal every time, which is manually programmed by setting DIP switches for a unique personal code. To program up to three channels, 1.
Page 147 4. The indicator light will blink slowly. In order from left to right, and within two and one-half minutes, enter each switch setting into the Universal Home Remote System. Push one button for each switch as follows: • Left button = “on” switch position. •...
Page 148 Programming Universal Home Remote — Rolling Code Rolling code garage door openers are used for garage doors produced after 1996 and are code protected. Rolling code means the coded signal is changed every time your remote control garage door opener is used. Programming a rolling code garage door opener involves time-sensitive actions, so read the entire procedure before you begin.
Page 149 3. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from ﬁve to 20 seconds. 4.
Page 150: Universal Home Remote System Operation (With One Triangular Led)
Universal Home Remote System Operation (With One Triangular LED) Your vehicle may have the Universal Home Remote System. If there is one triangular Light Emitting Diode (LED) above the Universal Home Remote buttons, follow the instructions below. If your vehicle has three round LED above the Universal Home Remote buttons, follow the instructions under Universal Home Remote System Operation (With three round LED).
Page 151 Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining...
Page 152 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart”...
Page 153: Storage Areas
Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1.
Page 154: Cupholder(S)
Cupholder(s) Your vehicle has cupholders located between the front seats. Slide the cover back to expose them. There are also cupholders in the armrest of the second row seat. Press the panel on the front of the armrest to expose the cupholders. On the outboard sides of the third row there may also be cupholders.
Page 155: Cargo Cover
If your vehicle has a luggage carrier, you can load things on top of your vehicle. The luggage carrier has side rails attached to the roof. You can get sliding crossrails through your dealer to use for tying things down. These let you load some things on top of your vehicle, as long as they are not wider or longer than the luggage carrier.
Page 156: Sunroof
Sunroof ® Sunroof (Ultra View CAUTION: People who are in a crash and not wearing a safety belt properly can suffer much worse injuries. They can hit things inside the vehicle or be ejected from it, and be seriously injured or killed. This is true for any vehicle occupant, in any motor vehicle.
Page 157 Press the back of the sunroof switch to open the sunroof. When the switch is pressed to the ﬁrst stop the sunroof will open to a desired position. Press the switch to the second stop to express open the sunroof to a preset comfort position.
Page 158: Sunroof (Ultra View Plus)
® Sunroof (Ultra View CAUTION: People who are in a crash and not wearing a safety belt properly can suffer much worse injuries. They can hit things inside the vehicle or be ejected from it, and be seriously injured or killed. This is true for any vehicle occupant, in any motor vehicle.
Page 159 One switch operates the front sunroof and another switch operates the front sunshade. The third switch is for the rear sunshade. Press the back of the sunroof switch to open the sunroof. Press the switch to the ﬁrst stop to open the sunroof to a desired position.
Page 160 Resynchronization To resynchronize the front sunroof and front and rear sunshades, do the following. 1. With the engine running, press and hold the rear sunshade switch in the closed position for about 15 seconds – the shade will move to the stop position.
Page 161: Instrument Panel
Section 3 Instrument Panel Overview ... 164 Hazard Warning Flashers ... 166 Other Warning Devices ... 166 Horn ... 166 Tilt Wheel ... 166 Turn Signal/Multifunction Lever ... 167 Turn and Lane-Change Signals ... 168 Headlamp High/Low-Beam Changer ... 169 Flash-to-Pass ...
Page 162 Section 3 Passenger Airbag Status Indicator ... 202 Charging System Light ... 204 Brake System Warning Light ... 204 Anti-Lock Brake System Warning Light ... 205 Traction Control System (TCS) Warning Light ... 206 Engine Coolant Temperature Warning Light ... 206 Engine Coolant Temperature Gage ...
Page 163 NOTES...
Page 164: Instrument Panel Overview
Instrument Panel Overview...
Page 165 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 194. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 167. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 198. D.
Page 166: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on the instrument panel below the climate control system.
Page 167: Turn Signal/Multifunction Lever
The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the steering wheel and pull the lever. Then move the steering wheel to a comfortable position and release the lever to lock the wheel in place.
Page 168: Turn And Lane-Change Signals
Turn and Lane-Change Signals To signal a turn, move the lever all the way up or down. The lever returns automatically when the turn is complete. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change.
Page 169: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer Push forward on the turn signal/multifunction lever to change the headlamps from low to high beam. Pull the lever back and then release it to change from high to low beam. If you turn the vehicle off with the high beams on, the high beams will be on the next time you start your vehicle.
Page 170: Windshield Wipers
Windshield Wipers The lever on the right side of the steering column operates the windshield wipers. (Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it.
Page 171: Windshield Washer
Windshield Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The windshield washer button is located at the end of the windshield wiper lever. (Washer Fluid): Press this button to wash the windshield.
Page 172: Rear Window Wiper/Washer
Rear Window Wiper/Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The switch for the rear washer/wiper is located in the overhead console.
Page 173: Headlamp Washer
Headlamp Washer Your vehicle may have headlamp washers. The headlamp washers clear debris from the headlamp lenses. The headlamp washers are located to the inside of the headlamps. To wash the headlamps, press the washer button located at the end of the windshield wiper lever. Both the headlamps and the windshield will be washed.
Page 174: Cruise Control
Cruise Control These controls are located on the end of the multifunction lever. (Off): Move to this position to turn the system off. (On): Move to this position to turn on the system. + (Resume/Accelerate): Move to this position to make the vehicle resume a previously set speed or to accelerate when cruise is already active.
Page 175 If your vehicle is in cruise control when the Traction Control System (TCS) begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on ® page 281 and StabiliTrak System on page 283. When road conditions allow you to safely use it again, you may turn the cruise control back on.
Page 176 Resuming a Set Speed Suppose you set the cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But it does not need to be reset. Once you are going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate.
Page 177 Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: • Press in the button at the end of the lever until you reach the lower speed desired, then release it. • To slow down in very small amounts, brieﬂy press the set button.
Page 178: Headlamps
Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has four positions: (On/Off): Turn the control to this position to turn off all lamps except the Daytime Running Lamps (DRL).
Page 179: Headlamps On Reminder
Headlamps on Reminder A warning chime will sound if the exterior lamp control is left on in either the headlamp or parking lamp position and the driver’s door is opened with the ignition off. See Lights On Reminder on page 212 for additional information. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during...
Page 180: Light Sensor
When the exterior lamp control is in AUTO and it is dark enough outside, the DRL will turn off and the low-beam headlamps will turn on. When it is bright enough outside, the low-beam headlamps will go off, and the DRL will turn back on. If you start the vehicle in a dark garage, the automatic headlamp system will come on immediately.
Page 181: Fog Lamps
Fog Lamps Use the fog lamps for better vision in foggy or misty conditions. The fog lamp controls are located on the turn signal/multifunction lever. (Fog Lamps): The band with this symbol is used to turn the fog lamps on and off. The parking lamps must be on for the fog lamps to work.
Page 182: Entry Lighting
Entry Lighting The entry lighting system turns on the reading and dome lamps and the backlighting to the exterior lamp control when a door is opened or if the Remote Keyless Entry (RKE) transmitter unlock button is pressed. If activated by the (RKE), the lighting will remain active for about 25 seconds.
Page 183: Electric Power Management
Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in.
Page 184: Ultrasonic Rear Parking
Ultrasonic Rear Parking Assist (URPA) Your vehicle may have the Ultrasonic Rear Parking Assist (URPA) system. It is designed to help you park while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h).
Page 185: How The System Works
The URPA display is located inside the vehicle, above the liftgate glass. It has three color-coded lights that can be seen through the rearview mirror or by turning around. How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R) and the vehicle speed is less than 3 mph (5 km/h).
Page 186: Accessory Power Outlet(S)
When the System Does Not Seem to Work Properly The light may ﬂash red when the vehicle is in REVERSE (R), if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush. Other conditions that may affect system performance include things like the vibrations from a jackhammer or the compression of air brakes on a very large...
Page 187: Ashtray(S) And Cigarette Lighter
Certain accessory power plugs may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should.
Page 188: Analog Clock
Cigarette Lighter Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown.
Page 189: Climate Controls
Climate Controls Dual Climate Control System With this system you can control the heating, cooling, defrosting, and ventilation for the vehicle. Dual Climate Control System Automatic Operation The climate control system automatically adjusts the air temperature, air delivery mode, fan speed, and air conditioning for best comfort in the vehicle.
Page 190 «ª (Driver’s Temperature Controls): Press the up or down buttons closest to the driver to manually increase or decrease the temperature inside the vehicle. «ª (Passenger’s Temperature Controls): Press the up or down buttons closest to the passenger to manually increase or decrease the temperature for the front passenger.
Page 191 (Defrost): Turn the control to this position so that most of the air is directed to the windshield with some air going to the side window outlets. More information on defrosting can be found later in this section. (On/Off): Press this button to turn the climate control system on or off.
Page 192: Air Conditioning
(Recirculation): This mode recirculates air inside the vehicle and keeps outside air from coming into the vehicle. It can be used to help cool the vehicle more quickly or to prevent odors from entering the vehicle. Recirculation is not available in the defrost mode. It is also cancelled when ﬂoor or defog mode is selected.
Page 193 There is also an interior temperature sensor located below the climate control system next to the steering wheel. There is also an ambient sensor located behind the grille in front of the vehicle. These sensors help the climate control system automatically control the temperature setting.
Page 194: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. < (Rear Defogger): Press the center of the right control to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible.
Page 195: Rear Air Conditioning System
Rear Air Conditioning System If your vehicle has the rear air conditioning system it has two fan speed selectors. One fan speed selector is located in the front overhead console and the other is located in the headliner above the second row seats.
Page 196 Use the procedure listed below to replace the passenger compartment air ﬁlter: 1. Open the hood to access the engine compartment. See Hood Release on page 355 for more information. Locate the passenger compartment air ﬁlter access panel door. 2. Push the two tabs on the access panel door towards the windshield.
Page 197: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 198: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using and many of the other things you will need to know to drive safely and economically.
Page 199: Speedometer And Odometer
Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). See “SPEEDOMETER” under DIC Controls and Displays on page 215 for more information. The odometer mileage can be checked without the vehicle running.
Page 200: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to ON or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds,...
Page 201: Airbag Readiness Light
Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the diagnostic module.
Page 202: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. United States When the ignition key is turned to ON or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 203 Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: Even though the passenger sensing system is designed to turn off the...
Page 204: Charging System Light
Charging System Light This light will come on brieﬂy when the ignition is turned to ON to show that it is working. It should turn off once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system.
Page 205: Anti-Lock Brake System Warning Light
When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 206: Traction Control System (Tcs) Warning Light
If the regular brake system warning light is not on, you still have brakes, but you do not have anti-lock brakes. If the regular brake system warning light is also on, you do not have anti-lock brakes and there is a problem with your regular brakes.
Page 207: Engine Coolant Temperature Gage
You should stop the vehicle and turn off the engine as soon as possible to avoid damage to the engine. A warning chime will sound when this light is on, also. See Engine Overheating on page 372. Engine Coolant Temperature Gage This gage shows the engine coolant temperature.
Page 208: Malfunction Indicator Lamp
This light will ﬂash for approximately 60 seconds and then turn on solid if a problem is detected with the Tire Pressure Monitor system. See Tire Pressure Monitor System on page 410 for more information. Malfunction Indicator Lamp Check Engine Light Your vehicle has a computer which monitors operation of the...
Page 209 This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: •...
Page 210 Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel.
Page 211: Oil Pressure Light
Oil Pressure Light CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.
Page 212: Security Light
Security Light For information regarding this light, see Theft-Deterrent System on page 112. Fog Lamp Light The fog lamps light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off.
Page 213: Highbeam On Light
Highbeam On Light This light comes on whenever the high-beam headlamps are on. See Headlamp High/Low-Beam Changer on page 169 for more information. Tow/Haul Mode Light This light comes on when the Tow/Haul mode has been activated. For more information, see Tow/Haul Mode on page 126.
Page 214: Driver Information Center (Dic)
All of the following situations are normal and do not indicate that anything is wrong with the fuel gage: • At the gas station the gas pump shuts off before the gage reads full. • The gage may change when you turn, stop quickly or accelerate quickly.
Page 215: Dic Controls And Displays
When the sport mode is active, an S will appear next to the shift position indicator on the center of the DIC display. When the manual mode is active, an M will appear on the DIC display. When the normal mode is active, only the shift position indicator will appear.
Page 216 Customization: Press this button to scroll through each of the customization features. See DIC Vehicle Customization on page 231 for more information on the customization features. Set/Reset: Press this button to reset certain DIC features and to acknowledge DIC warning messages and clear them from the DIC display.
Page 217 AVERAGE ECONOMY (AFE) This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this display was reset.
Page 218 BATTERY VOLTAGE This display shows the current battery voltage. Your vehicle’s charging system regulates voltage based on the state of the battery. The battery voltage may ﬂuctuate when viewing this information on the DIC. This is normal. If there is a problem with the battery charging system, the charging system light will illuminate and/or the DIC will display a message.
Page 219 UNITS This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. PARKING ASSIST If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, this display allows the system to be turned on or off.
Page 220: Dic Warnings And Messages
RELEARN REMOTE KEY This display allows you to match the remote keyless entry transmitter to your vehicle. To match a remote keyless entry transmitter to your vehicle, do the following: 1. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.
Page 221 AUTOMATIC LIGHT CONTROL OFF This message displays when the automatic headlamps are turned off. AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping below expected levels.
Page 222 See Tires on page 398, Loading Your Vehicle on page 322, and Inﬂation - Tire Pressure on page 407. The DIC display also shows the tire pressure values for the front and rear tires by pressing the vehicle information button. See DIC Controls and Displays on page 215.
Page 223 This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. See Engine Coolant Temperature Warning Light on page 206. See Overheated Engine Protection Operating Mode on page 374 for information on driving to a safe place in an emergency.
Page 224 OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible.
Page 225 REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle” under Remote Keyless Entry (RKE) System Operation on page 96 and DIC Controls and Displays on page 215 for more information. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in your Remote Keyless Entry (RKE) transmitter...
Page 226 SERVICE BRAKE ASSIST This message displays if there is a problem with the brake system. The brake system warning light and the anti-lock brake system warning light may also display on the instrument panel cluster. See Brake System Warning Light on page 204 and Anti-Lock Brake System Warning Light on page 205 for more information.
Page 227 SERVICE STABILITRAK This message displays if there has been a problem detected with the StabiliTrak If this message comes on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off then back on.
Page 228 SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message displays, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. See Traction Control System (TCS) on page 281 for more information.
Page 229 There are several conditions that can cause this message to appear. • One condition is overheating, which could ® occur if StabiliTrak activates continuously for an extended period of time. • The message also displays if the brake system warning light is on. See Brake System Warning Light on page 204.
Page 230 TIGHTEN GAS CAP This message displays when the fuel cap has not been fully tightened. Recheck the fuel cap to ensure that it is on and tightened properly. TIRE LEARNING ACTIVE If your vehicle has a Tire Pressure Monitor (TPM) system, this message displays when the system is re-learning the tire positions on your vehicle.
Page 231: Dic Vehicle Customization
WASHER FLUID LOW ADD FLUID This symbol appears with this message. This message displays when your vehicle is low on windshield washer ﬂuid. Reﬁll the windshield washer ﬂuid reservoir as soon as possible. See Windshield Washer Fluid on page 380 for more information.
Page 232 Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle: DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear back to English.
Page 233 Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: SHIFT OUT OF PARK (default): The vehicle’s doors automatically lock when the doors are closed and the vehicle is shifted out of PARK (P).
Page 234 REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open.
Page 235 Press the customization button until REMOTE DOOR UNLOCK appears on the DIC display. Press the set/reset button to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: LIGHTS OFF: The exterior lamps will not ﬂash when you press the unlock button on the RKE transmitter.
Page 236 NO CHANGE: No change will be made to this feature. The current setting will remain. Choose one of the available settings and press the set/reset button while it is displayed on the DIC to select it. EXIT LIGHTING If it is dark enough outside, this feature allows you to select the amount of time you want the exterior lamps to remain on.
Page 237 ON (default): If it is dark enough outside, the exterior lights will turn on brieﬂy when you unlock the vehicle with the RKE transmitter. The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off.
Page 238 DRIVER MIRROR: The driver’s outside mirror will be tilted down when the vehicle is shifted into REVERSE (R). PASSENGER MIRROR: The passenger’s outside mirror will be tilted down when the vehicle is shifted into REVERSE (R). BOTH MIRRORS: The driver’s and passenger’s outside mirrors will be tilted down when the vehicle is shifted into REVERSE (R).
Page 239 MEMORY SEAT RECALL If the vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat and Mirrors on page 12 for more information. Press the customization button until MEMORY SEAT RECALL appears in the display.
Page 240: Audio System(S)
Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs: • The vehicle is shifted out of PARK (P). • The ignition is no longer in ON. • The trip/fuel or vehicle information DIC buttons are pressed.
Page 241 CAUTION: This system provides you with a far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed. Always keep your eyes on the road and your mind on the drive —...
Page 242: Setting The Time
Setting the Time (Radio with Single CD Player) Enabling/Disabling the Digital Radio Clock Your vehicle has an analog clock as well as the digital radio clock. At the time of new vehicle delivery, the digital radio clock display should be disabled. If you decide to use the digital radio clock as well as the analog clock, you can change the setting to enable the radio clock display.
Page 243 Setting the Time and Date on the Digital Radio Clock If your vehicle has a radio with a single CD player, it has a clock button for setting the time and date. To set the time and date, do the following: 1.
Page 244: Setting The Time
Setting the Time (Radio with Six-Disc CD Player) Enabling/Disabling the Digital Radio Clock Your vehicle has an analog clock as well as the digital radio clock. At the time of new vehicle delivery, the digital radio clock display should be disabled. If you decide to use the digital radio clock as well as the analog clock, you can change the setting to enable the radio clock display.
Page 245 Setting the Time and Date on the Digital Radio Clock If your vehicle has a radio with a six-disc CD player, it has a MENU button for setting the time and date. To set the time and date, do the following: 1.
Page 246: Radio With Cd
Radio with CD Radio with CD shown, Radio with Six-Disc CD (MP3) similar Radio Data System (RDS) The audio system has a Radio Data System (RDS). The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available.
Page 247 Playing the Radio (Power/Volume): Press this knob to turn the system on and off. Turn this knob clockwise or counterclockwise to increase or decrease the volume. Speed Compensated Volume (SCV): The radio also has Speed Compensated Volume (SCV). While SCV is on, the radio volume automatically adjusts to compensate for road and wind noise as driving speed changes.
Page 248 (Information) (XM™ Satellite Radio Service, MP3, and RDS Features): Press the information button to display additional text information related to the current FM-RDS or XM™ station, or MP3 song. A choice of additional information such as: Channel, Song, Artist, CAT (category) can appear.
Page 249 The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages, perform the following steps: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label.
Page 250 Finding a Category (CAT) Station CAT (Category): The CAT button is used to ﬁnd XM™ stations when the radio is in the XM™ mode. To ﬁnd XM™ channels within a desired category, perform the following: 1. Press the BAND button until the XM™ frequency displays.
Page 251: Radio Message
Radio Message Locked: This message displays when the ® THEFTLOCK system has locked up the radio. Take the vehicle to your dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer. Radio Messages for XM™ Only See XM Radio Messages on page 264 later in this section for further detail.
Page 252 (Eject): Press the CD eject button to eject the CD. If the CD is not removed, after several seconds, the CD automatically pulls back into the player. (Tune): Turn this knob to select tracks on the CD currently playing. © ¨...
Page 253 CD/AUX (CD/Auxiliary): Press this button to play a CD when listening to the radio. The CD icon and track number displays when a CD is in the player. Press this button again and the system automatically searches for an auxiliary input device, such as a portable audio player.
Page 254 Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen. Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or...
Page 255 RDM (Random): With the random setting, the tracks can be listened to in random, rather than sequential order, on one CD or all CDs in a six-disc CD player. To use random, do one of the following: • To play the tracks from the CD you are listening to in random order, press the pushbutton positioned under the RDM label until Randomize Current Disc displays.
Page 256 • There could have been a problem while burning the CD. • The label could be caught in the CD player. If the CD is not playing correctly, for any other reason, try a known good CD. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer.
Page 257: Using An Mp3
Using an MP3 MP3/WMA CD-R or CD-RW Disc The radio plays MP3 and WMA ﬁles that were recorded on a CD-R or CD-RW disc. The ﬁles can be recorded with the following ﬁxed bit rates: 32 kbps, 40 kbps, 56 kbps, 64 kbps, 80 kbps, 96 kbps, 112 kbps, 128 kbps, 160 kbps, 192 kbps, 224 kbps, 256 kbps, and 320 kbps or a variable bit rate.
Page 258 • Minimize the length of the ﬁle, folder or playlist names. Long ﬁle, folder, or playlist names, or a combination of a large number of ﬁles and folders, or playlists can cause the player to be unable to play up to the maximum number of ﬁles, folders, playlists, or sessions.
Page 259 No Folder When the CD-R contains only compressed ﬁles, the ﬁles are located under the root folder. The next and previous folder functions do not display on a CD-R that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT.
Page 260 Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp™, MusicMatch™, or Windows Media Player™ software can be accessed, however, they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song ﬁles. Playlists must have a ﬁle extension of M3U or WPL.
Page 261 Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials,...
Page 262 FWD (Fast Forward): Press and hold this button to advance playback quickly within an MP3 ﬁle. Sound is heard at a reduced volume. Release this button to resume playing the ﬁle. The elapsed time of the ﬁle displays. RDM (Random): With the random setting, MP3 ﬁles on the CD-R can be played in random, rather than sequential order, on one CD-R or all discs in a six-disc CD player.
Page 263 To change from playback by artist to playback by album, press the pushbutton located below the Sort By label. From the sort screen, push one of the buttons below the album button. Press the pushbutton below the Back label to return to the main music navigator screen.
Page 264: Xm Radio Messages
XM Radio Messages Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. XM Updating Updating encryption code The encryption code in the receiver is being updated, and No XM Signal Loss of signal Loading XM Acquiring channel audio...
Page 265 Radio Display Message No CAT Info Category Name not available No Information No Text/Informational message available CAT Not Found No channel available for the chosen category XM TheftLocked Theft lock active XM Radio ID Radio ID label (channel 0) If tuned to channel 0, this message can alternate with the Unknown Radio ID not known (should only be if...
Page 266: Navigation/Radio System
Navigation/Radio System Your vehicle could have a navigation radio system. The navigation system has built-in features intended to minimize driver distraction. Technology alone, no matter how advanced, can never replace your own judgment. See the Navigation System manual for some tips to help you reduce distractions while driving.
Page 267 (Power): Press this button to turn the RSA on or off. Volume: Turn this knob to increase or to decrease the volume of the wired headphones. The left knob controls the left headphones and the right knob controls the right headphones. SRCE (Source): Press this button to switch between the radio (AM/FM), XM™...
Page 268: Theft-Deterrent Feature
When a DVD video menu is being displayed, press the seek up arrow or seek down arrow to perform a cursor up or down on the menu. Hold the seek up arrow or seek down arrow to perform a cursor right or left on the menu.
Page 269: Audio Steering Wheel Controls
Audio Steering Wheel Controls Some audio controls can be adjusted at the steering wheel. They include the following: (Mute): Press this button to mute the system. Press this button again, or any other radio button, to turn the sound on. SRCE (Source): Press this button to switch between AM, FM, XM™...
Page 270: Radio Reception
(Volume): Press this button to increase or to decrease the volume. (Seek): Press either arrow to go to the next or the previous radio station and stay there. The radio seeks stations only with a strong signal that are in the selected band. While a CD is playing in a single CD player, press the minus button to go to the previous track or the plus button to go to the next track on the CD.
Page 271: Care Of Your Cds
XM™ Satellite Radio Service XM™ Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause the loss of XM™...
Page 272: Diversity Antenna System
Diversity Antenna System The AM-FM antenna is integrated within the rear quarter windows. Make sure the inside surface of the rear quarter windows are not scratched and the grid lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Page 273: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ... 274 Defensive Driving ... 274 Drunken Driving ... 275 Control of a Vehicle ... 278 Braking ... 278 Anti-Lock Brake System (ABS) ... 279 Braking in Emergencies ... 281 Traction Control System (TCS) ... 281 Magnetic Ride Control ...
Page 274: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 22. CAUTION: Defensive driving really means “Be ready for anything.”...
Page 275: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 276 According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin, or vodka.
Page 277 But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent.
Page 278: Control Of A Vehicle
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road.
Page 279: Anti-Lock Brake System (Abs)
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. The brakes may not have time to cool between hard stops. The brakes will wear out much faster if you do a lot of heavy braking.
Page 280 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
Page 281: Braking In Emergencies
Remember: ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 282 See Traction Control System (TCS) Warning Light on page 206. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly. The TCS automatically comes on whenever you start your vehicle. To limit wheel spin, especially in slippery road conditions, you should always leave the system on.
Page 283: Magnetic Ride Control
Magnetic Ride Control Your vehicle may have Magnetic Ride Control that automatically adjusts the ride of your vehicle. Automatic ride control is achieved through a computer used to control and monitor the suspension system. The controller receives input from various sensors to determine the proper system response.
Page 284: Panic Brake Assist
If there is a problem detected with StabiliTrak SERVICE STABILITRAK message will be displayed on the Driver Information Center. See DIC Warnings and Messages on page 220. When this message is displayed, the system is not operational. Driving should be adjusted accordingly.
Page 285: Steering
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips It is important to take curves at a reasonable speed.
Page 286 Try to adjust your speed so you can “drive” through the curve. Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway. Adding non-GM accessories can affect your vehicle’s performance.
Page 287: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 288 So here are some tips for passing: • Drive ahead. Look down the road, to the sides, and to crossroads for situations that might affect your passing patterns. If you have any doubt whatsoever about making a successful pass, wait for a better time. •...
Page 289: Loss Of Control
• Check your vehicle’s mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your vehicle’s inside mirror, activate the right lane change signal and move back into the right lane.
Page 290 Remember: Any traction control system helps avoid only the acceleration skid. If your traction control system is off, then an acceleration skid is also best handled by easing your foot off the accelerator pedal. If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go.
Page 291: Off-Road Driving
Off-Road Driving This off-road guide is for vehicles that have all-wheel drive. If your vehicle does not have all-wheel drive, you should not drive off-road unless you are on a level, solid surface. Many of the same design features that help make your vehicle responsive on paved roads during poor weather conditions —...
Page 292 Loading Your Vehicle for Off-Road Driving CAUTION: • Cargo on the load ﬂoor piled higher than the seatbacks can be thrown forward during a sudden stop. You or your passengers could be injured. Keep cargo below the top of the seatbacks.
Page 293 Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • Always use established trails, roads, and areas that have been specially set aside for public off-road recreational driving;...
Page 294 Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • You approach things faster and you have less time to scan the terrain for obstacles.
Page 295 Surface Obstacles: Unseen or hidden obstacles can be hazardous. A rock, log, hole, rut, or bump can startle you if you are not prepared for them. Often these obstacles are hidden by grass, bushes, snow, or even the rise and fall of the terrain itself.
Page 296 Driving on Off-Road Hills Off-road driving often takes you up, down, or across a hill. Driving safely on hills requires good judgment and understanding of what your vehicle can and cannot do. There are some hills that simply cannot be driven, no matter how well built the vehicle.
Page 297: Driving Uphill
• What is beyond the hill? Is there a cliff, an embankment, a drop-off, a fence? Get out and walk the hill if you do not know. It is the smart way to ﬁnd out. • Is the hill simply too rough? Steep hills often have ruts, gullies, troughs, and exposed rocks because they are more susceptible to the effects of erosion.
Page 298 • Sound the horn as you approach the top of the hill to let opposing traffic know you are there. • Use your headlamps, even during the day. They make you more visible to oncoming traffic. CAUTION: Driving to the top (crest) of a hill at full speed can cause an accident.
Page 299 • As you are backing down the hill, put your left hand on the steering wheel at the 12 o’clock position. This way you will be able to tell if your wheels are straight and maneuver as you back down. It is best that you back down the hill with your wheels straight rather than in the left or right direction.
Page 300: Driving Downhill
Driving Downhill When off-roading takes you downhill, you will want to consider a number of things: • How steep is the downhill? Will I be able to maintain vehicle control? • What is the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? •...
Page 301: Driving Across An Incline
Am I likely to stall when going downhill? It is much more likely to happen going uphill. But if it happens going downhill, here is what to do. 1. Stop your vehicle by applying the regular brakes. Apply the parking brake. 2.
Page 302 • Hidden obstacles can make the steepness of the incline even worse. If you drive across a rock with the uphill wheels, or if the downhill wheels drop into a rut or depression, your vehicle can tilt even more. For reasons like these, you need to decide carefully whether to try to drive across an incline.
Page 303 Stalling on an Incline If your vehicle stalls when you are crossing an incline, be sure you, and any passengers, get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
Page 304 Driving in Mud, Sand, Snow, or Ice When you drive in mud, snow, or sand, the wheels will not get good traction. You cannot accelerate as quickly, turning is more difficult, and you will need longer braking distances. It is best to use a low gear when you are in mud —the deeper the mud, the lower the gear.
Page 305 Driving in Water Heavy rain can mean ﬂash ﬂooding, and ﬂood waters demand extreme caution. Find out how deep the water is before you drive through it. If it is deep enough to cover your wheel hubs, axles, or exhaust pipe, do not try it — you probably will not get through.
Page 306: Driving At Night
After Off-Road Driving Remove any brush or debris that has collected on the underbody, chassis, or under the hood. These accumulations can be a ﬁre hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Page 307 No one can see as well at night as in the daytime. But as we get older these differences increase. A 50-year-old driver may require at least twice as much light to see the same thing at night as a 20-year-old.
Page 308: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 309 CAUTION: Wet brakes can cause accidents. They may not work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply the brake pedal lightly until the brakes work normally.
Page 310 Driving Through Flowing Water CAUTION: Flowing or rushing water creates strong forces. If you try to drive through ﬂowing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of ﬂowing water can carry away a smaller vehicle.
Page 311: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: •...
Page 312: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 313: Before Leaving On A Long Trip
Before changing lanes, check your mirrors. Then use your turn signal. Just before you leave the lane, glance quickly over your shoulder to make sure there is not another vehicle in your blind spot. Once you are moving on the freeway, make certain you allow a reasonable following distance.
Page 314: Highway Hypnosis
• Tires: They are vitally important to a safe, trouble-free trip. Is the tread good enough for long-distance driving? Are the tires all inﬂated to the recommended pressure? • Weather Forecasts: What is the weather outlook along your route? Should you delay your trip a short time to avoid a major storm system? •...
Page 315: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. See Off-Road Driving on page 291 for information about driving off-road.
Page 316 CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Page 317: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 398. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning...
Page 318 What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing, 32°F (0°C), and freezing rain begins to fall.
Page 319 The Anti-Lock Brake System (ABS) improves your vehicle’s stability when you make a hard stop on a slippery road. Even though you have ABS, you will want to begin stopping sooner than you would on dry pavement. See Anti-Lock Brake System (ABS) on page 279.
Page 320 You can run the engine to keep warm, but be careful. CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 321: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
You will need a well-charged battery to restart the vehicle, and possibly for signaling later on with your headlamps. Let the heater run for a while. Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold.
Page 322: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right. That will clear the area around the front wheels. ® Turn the StabiliTrak System off. See StabiliTrak System on page 283. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Page 323 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms...
Page 324 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 325 Example 1 Item Description Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Vehicle Capacity Weight 1,000 lbs (453 kg)
Page 326 Example 3 Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 327 The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 328: Towing
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going.
Page 329 With the proper preparation and equipment, many vehicles can be towed in these ways. See “Dinghy Towing” and “Dolly Towing,” following. Here are some important things to consider before you do recreational vehicle towing: • What’s the towing capacity of the towing vehicle? Be sure you read the tow vehicle manufacturer’s recommendations.
Page 330: Level Control
If you have a Rear-Wheel Drive (RWD) vehicle, it can be towed using a dolly. If you have an All-Wheel-Drive (AWD) vehicle, it can only be towed on a ﬂat-bed trailer. To tow your RWD vehicle using a dolly, follow these steps: 1.
Page 331: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
Page 332 If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Page 333 Tow/Haul Mode Tow/haul is designed to assist while your vehicle is pulling a large or heavy load or trailer. Tow/haul is most useful while pulling such a load in rolling terrain, in stop-and-go traffic, or when you need improved low-speed control, such as when parking.
Page 334 The GCWR for your vehicle should not be exceeded. You can ask your dealer for our trailering information or advice, or you can write us at: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169...
Page 335 Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 336 Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It has a GVWR of 7,200 lbs (3 266 kg), a RGAWR of 4,000 lbs (1 814 kg) and a GCWR (Gross Combination Weight Rating) of 14,000 lbs (6 350 kg).
Page 337 Because your rear axle now weighs 3,100 lbs (1 406 kg), you can only put 900 lbs (408 kg) on the rear axle without exceeding RGAWR. The effect of tongue weight is about 1.5 times the actual weight. Dividing the 900 lbs (408 kg) by 1.5 leaves you with being able to handle only 600 lbs (272 kg) of tongue weight.
Page 338 Safety Chains You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer.
Page 339 Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You’ll need more passing distance up ahead when you’re towing a trailer.
Page 340 Driving on Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift down, you might have to use your brakes so much that they would get hot and no longer work well.
Page 341 When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 342 NOTES...
Page 343: Service And Appearance Care
Section 5 Service ... 346 Accessories and Modiﬁcations ... 347 California Proposition 65 Warning ... 347 Doing Your Own Service Work ... 348 Adding Equipment to the Outside of Your Vehicle ... 348 Fuel ... 349 Gasoline Octane ... 349 Gasoline Speciﬁcations ...
Page 344 Section 5 Tires ... 398 Winter Tires ... 400 Tire Sidewall Labeling ... 401 Tire Terminology and Deﬁnitions ... 404 Inﬂation - Tire Pressure ... 407 High-Speed Operation ... 409 Tire Pressure Monitor System ... 410 Tire Inspection and Rotation ... 414 When It Is Time for New Tires ...
Page 345 Section 5 Vehicle Identiﬁcation ... 453 Vehicle Identiﬁcation Number (VIN) ... 453 Service Parts Identiﬁcation Label ... 453 Electrical System ... 454 Add-On Electrical Equipment ... 454 Windshield Wiper Fuses ... 454 Power Windows and Other Power Options ... 454 Service and Appearance Care Fuses and Circuit Breakers ...
Page 346: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 347: Accessories And Modiﬁcations
Accessories and Modiﬁcations When you add non-GM accessories to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like anti-lock brakes, traction control and stability control.
Page 348: Doing Your Own Service Work
Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task.
Page 349: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. To help keep your engine clean and maintain optimum vehicle performance, GM recommends the use of gasoline advertised as TOP TIER Detergent Gasoline. The 8th digit of your Vehicle Identiﬁcation Number (VIN) shows the code letter or number that identiﬁes your engine.
Page 350: Gasoline Speciﬁcations
Gasoline Speciﬁcations At a minimum, gasoline should meet ASTM speciﬁcation D 4814 in the United States or CAN/CGSB-3.5 in Canada. Some gasolines may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). General Motors recommends against the use of gasolines containing MMT. See Additives on page 350 for additional information.
Page 351: Fuels In Foreign Countries
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area. General Motors recommends that you use these gasolines if they comply with the speciﬁcations described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels.
Page 352: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling.
Page 353 CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather.
Page 354: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 355: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release lever with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and ﬁnd the secondary hood release lever.
Page 356: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.6L V6 engine, you will see the following:...
Page 357 A. Underhood Fuse Block. See Underhood Fuse Block on page 455. B. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 380. C. Battery. See Battery on page 385. D. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 195.
Page 358 When you open the hood on the 4.6L V8 engine, you will see the following:...
Page 359 A. Underhood Fuse Block. See Underhood Fuse Block on page 455. B. Battery. See Battery on page 385. C. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 195. D. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 380.
Page 360: Engine Oil
Engine Oil Your vehicle may have an oil pressure light on the instrument cluster. There is also an OIL PRESSURE LOW STOP ENGINE message on the Driver Information Center (DIC). If the light and/or message appears, check the engine oil level right away. For more information, see “OIL PRESSURE LOW STOP ENGINE”...
Page 361 When to Add Engine Oil 3.6L V6 Engine 4.6L V8 Engine If the oil is below the cross-hatched area at the tip of the dipstick, you need to add at least one quart/liter of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 362 What Kind of Engine Oil to Use Look for two things: • GM4718M Your vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard.
Page 363: Engine Oil Life System
Look for this on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM4718M and have the starburst symbol on the front of the oil container. Your vehicle’s engine is ﬁlled at the factory with a ®...
Page 364 However, the engine oil and ﬁlter must be changed at least once a year and at this time the system must be reset. Your dealer has GM-trained service people who will perform this work using genuine GM parts and reset the system. It is also important to check the oil regularly and keep it at the proper level.
Page 365: Engine Air Cleaner/Filter
What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
Page 366 When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (83 000 km) interval. See Scheduled Maintenance on page 471 for more information. If you are driving in dusty/dirty conditions, inspect the ﬁlter at each engine oil change.
Page 367: Automatic Transmission Fluid
Automatic Transmission Fluid How to Check Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to the dealership service department and have it repaired as soon as possible.
Page 368: Engine Coolant
Engine Coolant The cooling system in your vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in your vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, if you add only DEX-COOL life coolant.
Page 369 What to Use Use a mixture of one-half clean, drinkable water ® and one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 370 Checking Coolant The coolant surge tank and pressure cap are located on the driver’s side of the vehicle, toward the rear of the engine compartment. See Engine Compartment Overview on page 356 for more information on location. CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 371: Coolant Surge Tank Pressure Cap
Adding Coolant If you need more coolant, add the proper ® DEX-COOL coolant mixture at the surge tank, but only when the engine is cool. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough.
Page 372: Engine Overheating
Engine Overheating There are two engine hot messages that could be displayed in the Driver Information Center (DIC). See DIC Warnings and Messages on page 220 for more information. If the engine is overheating, then you will ﬁnd a coolant temperature gage and a coolant warning light on the instrument panel.
Page 373 If No Steam Is Coming From Your Engine An overheat warning, can indicate a serious problem. If you get an engine overheat warning but see or hear no steam, the problem might not be too serious. Sometimes the engine can get a little too hot when you: •...
Page 374: Overheated Engine Protection
Overheated Engine Protection Operating Mode This operating mode allows your vehicle to be driven to a safe place in an emergency. Should an hot engine condition exist, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage. In this mode, there is a loss in power and engine performance.
Page 375 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing, and tools away from any underhood electric fan. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down.
Page 376 Notice: Using coolant other than DEX-COOL may cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner, at 30,000 miles (50 000 km) or 24 months, whichever occurs ﬁrst. Any repairs would not be covered by your warranty.
Page 377 CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning.
Page 378 2. Then keep turning the pressure cap slowly, 3. Fill the coolant surge tank with the proper and remove it. mixture, to slightly above the FULL COLD/FROID line on the side of the coolant surge tank.
Page 379: Power Steering Fluid
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. The upper radiator hose is the largest of the hoses which comes out of the radiator, on the passenger’s side of the vehicle.
Page 380: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 381: Brakes
Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system. Also, water does not clean as well as washer ﬂuid.
Page 382 So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings.
Page 383 What to Add When you do need brake ﬂuid, DOT-3 brake ﬂuid is recommended for use. DOT-4 brake ﬂuid is also compatible with your vehicle’s brake system parts. However, if you choose to use DOT-4 ﬂuid, it is recommended that you ﬂush your brake hydraulic system and reﬁll it with new DOT-4 ﬂuid at a regular maintenance service every two years.
Page 384 Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 385: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 386: Jump Starting
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( ) cable from the battery. This will help keep the battery from running down. CAUTION: Batteries have acid that can burn you and gas that can explode.
Page 387 Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 388 4. Open the hoods and locate the positive (+) and negative ( ) terminal locations of the other vehicle, as well as the positive (+) terminal location on your vehicle’s battery. See Engine Compartment Overview on page 356 for more information on the location of the battery.
Page 389 Notice: If you connect a negative cable to the ECM, ECM mounting bracket, or any cables that attach to the ECM bracket, you may damage the ECM. Always attach the negative cable to your vehicle’s remote negative ground location, instead of the ECM, ECM bracket, or any cables attached to the ECM bracket.
Page 390 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 391 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( ) cable to the negative terminal of the good battery.
Page 392: All-Wheel Drive
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 393 How to Check Lubricant A. Drain Plug B. Fill Plug To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, located on the transfer case, you’ll need to add some lubricant.
Page 394: Rear Axle
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 395: Front Axle
Front Axle When to Check and Change Lubricant It is not necessary to regularly check the front axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant A.
Page 396: Bulb Replacement
Bulb Replacement It is recommended that all bulbs be replaced by your dealer. High Intensity Discharge (HID) Lighting CAUTION: The low beam high intensity discharge lighting system operates at a very high voltage. If you try to service any of the system components, you could be seriously injured.
Page 397: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 471 for more information. It’s a good idea to clean or replace the wiper blade assembly on a regular basis or when worn. For proper windshield wiper blade length and type, see Normal Maintenance Replacement Parts on page 482.
Page 398: Tires
6. Replace the blade with a new one. 7. Reinstall the wiper blade assembly by sliding it over the wiper arm to engage the J-hooked end. Pull up on the assembly to lock it into place. 8. Repeat the steps for the other wiper. Rear Wiper Blade Replacement To replace the rear wiper blade follow the steps listed previously.
Page 399 CAUTION: • Poorly maintained and improperly used tires are dangerous. • Overloading your tires can cause overheating as a result of too much friction. You could have an air-out and a serious accident. See Loading Your Vehicle on page 322. •...
Page 400: Winter Tires
Low-Proﬁle Performance Tire If your vehicle has P255/50R20 size tires, they are classiﬁed as low-proﬁle performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster.
Page 401: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 402 (D) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 403 (B) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identiﬁcation Number (TIN): The letters and numbers following the DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured.
Page 404: Tire Terminology And Deﬁnitions
(B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide.
Page 405 Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inﬂation - Tire Pressure on page 407. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo.
Page 406 Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading Your Vehicle on page 322.
Page 407: Inﬂation - Tire Pressure
Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 416. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear.
Page 408 A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Page 409: High-Speed Operation
High-Speed Operation CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inﬂation pressure adjustment for high speed operation.
Page 410: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. If your vehicle has this feature, sensors are mounted on each tire and wheel assembly, except for the compact spare tire and wheel. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit the tire pressure readings to a receiver located in the vehicle.
Page 411 Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inﬂation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inﬂation pressure label, you should determine the proper tire inﬂation pressure for those tires.)
Page 412 When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
Page 413 The TPM matching process is outlined below: 1. Set the parking brake. 2. Turn the ignition switch to ON with the engine off. 3. Using the DIC, press the vehicle information button until the PRESS TIRE POSITIONS message displays. 4. Press the Set/Reset button. The horn sounds twice to indicate the TPMS receiver is ready, and the TIRE LEARNING ACTIVE message displays.
Page 414: Tire Inspection And Rotation
Federal Communications Commission (FCC) and Industry and Science Canada This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Page 415 The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The ﬁrst rotation is the most important. See Scheduled Maintenance on page 471. When rotating P255/50R20 size tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation.
Page 416: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.
Page 417 GM’s TPC Spec number is molded onto the tire’s sidewall by the tire manufacturer. If the tires have an all-season tread design, the TPC spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 401 for additional information.
Page 418: Different Size Tires And Wheels
If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires. Vehicles that have a tire pressure monitoring system may give an inaccurate low-pressure warning if non-TPC spec rated tires are installed...
Page 419: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 420: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 421: Wheel Replacement
Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired).
Page 422: Tire Chains
Used Replacement Wheels CAUTION: Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 423: If A Tire Goes Flat
Notice: If your vehicle has a tire size other than P255/50R20 use tire chains only where legal and only when you must. Use chains that are the proper size for your tires. Install them on the tires of the rear axle. Do not use chains on the tires of the front axle.
Page 424: Changing A Flat Tire
CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
Page 425 CAUTION: (Continued) 3. Turn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed.
Page 426: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the rear of the vehicle. To access the equipment, do the following: 1. Remove the storage bin to access the jack if your vehicle has the cargo management system.
Page 427 Removing the Spare Tire The compact spare tire is located under the vehicle, ahead of the rear bumper. See Compact Spare Tire on page 442 for more information about the compact spare. To remove the spare tire from the vehicle, do the following: A.
Page 428 5. Tilt the retainer (C) and slip it through the wheel opening to remove the spare tire from the cable (B). 6. Turn the wrench clockwise until you feel two slips or hear two clicks after removing the spare tire to raise the cable back up. Do not store a full-size or a ﬂat road tire under the vehicle.
Page 429: Removing The Flat Tire And Installing The Spare Tire
2. If it is visible, ﬁrst try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot over-tighten the cable. 3. Loosen the cable then by turning the wrench counterclockwise three or four turns.
Page 430 2. Find the jacking 3. Attach the wheel wrench to the jack. location using the hoisting notches located in the plastic Getting under a vehicle when it is jacked molding. The notches in the up is dangerous. If the vehicle slips off plastic molding are the jack you could be badly injured or marked with a...
Page 431 CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
Page 432 6. Put the compact spare tire near you. 7. Raise the vehicle by turning the wheel wrench clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt under the vehicle. 8. Remove all the wheel nuts and take off the ﬂat tire.
Page 433 CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
Page 434 13. Lower the vehicle by attaching the wheel wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. 14. Tighten the wheel Do not try to put a wheel cover on the compact spare tire. It will not ﬁt. Store the wheel cover securely in the rear of the vehicle until you have the ﬂat tire repaired or replaced.
Page 435 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Page 436: Secondary Latch System
Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
Page 437 To release the spare tire from the secondary latch, do the following: 1. If the cable is not visible, start this procedure at Step 3. 2. If the cable is visible, 3. Attach the wheel wrench to the jack and raise the jack at least 10 turns.
Page 438 8. Grasp the spare tire with both hands and pull it out from under the vehicle. 9. Reach under the vehicle and remove the wheel wrench and jack. 10. Tilt the retainer and slip it through the wheel opening when the spare tire has been completely lowered.
Page 439: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 440 Storing the Flat Tire with a Flat Load Floor 1. Put back all tools as they were stored in the rear storage compartment and put the compartment cover back on. 2. Place the ﬂat tire in the tire storage bag and put the tire in a horizontal position on the ﬂoor in the rear of the vehicle.
Page 441 To store the spare tire and tools, do the following: 1. Lay the compact spare tire on the ground at the rear of the vehicle. Position the compact spare tire so that the valve stem is pointed down facing the rear of the vehicle. 2.
Page 442: Compact Spare Tire
8. Make sure the tire is stored securely. Push, pull (A), and then try to turn the tire (B). If the tire moves, use the wheel wrench to tighten the cable. Put back all tools as they were stored in the rear storage compartment and put the compartment cover back on.
Page 443: Appearance Care
Notice: When the compact spare is installed, do not take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle. Do not use the compact spare on other vehicles.
Page 444 Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles.
Page 445: Fabric/Carpet
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on ﬂoor carpet and carpeted ﬂoor mats. For soils, always try to remove them ﬁrst with plain water or club soda.
Page 446: Leather
Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather.
Page 447: Wood Panels
Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.
Page 448: Cleaning Exterior Lamps/Lenses
All cleaning agents should be ﬂushed promptly and not allowed to dry on the surface, or they could stain. Dry the ﬁnish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.
Page 449: Windshield And Wiper Blades
Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a glass cleaning liquid or powder and water solution.
Page 450: Tires
Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application.
Page 451: Finish Damage
Finish Damage Any stone chips, fractures or deep scratches in the ﬁnish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer. Larger areas of ﬁnish damage can be corrected in your dealer’s body and paint shop.
Page 452: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Removes tar, road oil, Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. White Sidewall Removes soil and black Tire Cleaner marks from whitewalls.
Page 453: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. You can see it if you look through the windshield from outside your vehicle.
Page 454: Electrical System
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 455: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of ﬁres caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 456 Relays FAN 2 HC Right Side Engine Cooling MICRO Fan Motors FAN S/P HC Series/Parallel Engine MICRO Cooling Fan Usage Relays WASHER SS MICRO FAN 1 HC MICRO Usage FRNT Front Washer Pump Left Side Engine Cooling Fan Motors...
Page 457 Relays Usage FOG LAMP SS Front Fog Lamps MICRO SPARE Spare IGN MAIN SS Ignition Switch (ON) MICRO STRTR HC Starter Solenoid MICRO PWR/TRN HC Powertrain/Engine Control Module MICRO HI BEAM SS High-Beam Headlamps MICRO BLWR HC Front Blower Motor Assembly MICRO WPR HC Windshield Wiper System - On/Off...
Page 458 J Case Fuses BLWR Front Blower Motor Assembly RRPDB (Right Side Rear RPDB 2 Power Distribution Box) Mini Fuses FRNT Front Washer Pump WASHER SPARE Spare SPARE Spare Sensing Diagnostic Module (SDM), AIRBAG Occupant Sensor Display, Instrument Cluster Anti-lock Braking System Ignition, ABS IGN Variable Effort Steering IGN SW...
Page 459 Mini Fuses Usage RT HI BEAM Right Side High-Beam Headlamp Battery Regulated Voltage RVC SNSR Control Sense FOG LAMP Front Fog Lamps ECM 1 Engine Control Module (ECM) Left Side Front Turn Lamps, BCM 5 Rear Stoplamps, Turn Lamps Windshield Wiper Motor SPARE Spare Center High-Mounted Stoplamp...
Page 460: Rear Underseat Fuse Block
Rear Underseat Fuse Block (Left Side) The left side rear fuse block is located under the rear seat on the left side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 461 Mini Fuses Usage Rear Seat Module, Flip/Fold Motors DRIVER DR Driver Door Module (Locks, Outside Rearview Mirror, Window Switches) STOP LAMPS Not Used MARKER License Lamps LAMP LH PRK POS Left Side Taillamp, Left Side Front LAMPS Park Lamps, Sidemarker Lamps Right Side Taillamp, Right Side RH PRK Front Park Lamps, Sidemarker...
Page 462: Rear Underseat Fuse Block
Rear Underseat Fuse Block (Right Side) The right side rear fuse block is located under the rear seat on the right side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 463 Mini Fuses Usage REAR DEFOG Rear Window Defogger SPARE Spare Hush Panel Lamps, Overhead BCM 3 Courtesy Lamp Assembly, Right Side Front Turn Lamp REAR A/C Rear Air Conditioning System Climate Control Module HDT STR WHL Not Used SPARE Spare SPARE Spare SPARE...
Page 464: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 480 for more information. Application Air Conditioning Refrigerant Automatic Transmission (Pan Removal and Replacement) 5-Speed Automatic 6-Speed Automatic Cooling System 3.6L V6 4.6L V8 Engine Oil with Filter...
Page 465 Application Fuel Tank Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual. Recheck ﬂuid level after ﬁlling. Engine 3.6L V6 4.6L V8 Engine Speciﬁcations VIN Code Transmission Automatic Automatic Capacities...
Page 466 NOTES...
Page 467: Maintenance Schedule
Section 6 Maintenance Schedule ... 468 Introduction ... 468 Maintenance Requirements ... 468 Your Vehicle and the Environment ... 468 Using the Maintenance Schedule ... 469 Scheduled Maintenance ... 471 Additional Required Services ... 473 Maintenance Footnotes ... 474 Maintenance Schedule Owner Checks and Services ...
Page 468: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and...
Page 469: Using The Maintenance Schedule
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 470 The services in Scheduled Maintenance on page 471 should be performed when indicated. See Additional Required Services on page 473 and Maintenance Footnotes on page 474 for further information. CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured.
Page 471: Scheduled Maintenance
Scheduled Maintenance When the CHANGE ENGINE OIL SOON message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 472 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 360. Reset oil life system. See Engine Oil Life System on page 363. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage.
Page 473: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 474: Maintenance Footnotes
Service and Miles (Kilometers) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (l). If using DOT-4 brake ﬂuid, change brake ﬂuid at a regular maintenance service every two years.
Page 475 (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, ﬁttings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year.
Page 476: Owner Checks And Services
(i) Drain, ﬂush, and reﬁll cooling system. This service can be complex; you should have your dealer perform this service. See Engine Coolant on page 368 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and ﬁller neck. Pressure test the cooling system and pressure cap.
Page 477: At Least Once A Month
Notice: It is important to check the engine oil regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by your warranty. Engine Coolant Level Check Check the engine coolant level and add ®...
Page 478 Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 479 Parking Brake and Automatic Transmission Park (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 480: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Usage Fluid/Lubricant The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard can be identiﬁed as synthetic, and should also be identiﬁed with the American Petroleum Institute (API) Certiﬁed...
Page 481 Usage Fluid/Lubricant SAE 75W-90 Synthetic Axle Lubricant Front and Rear (GM Part No. U.S. 12378261, Axle in Canada 10953455) meeting GM Speciﬁcation 9986115. Manual Transmission Fluid Transfer Case (GM Part No. U.S. 88861800, in Canada 88861801). Multi-Purpose Lubricant, Superlube Hood Hinges (GM Part No.
Page 482: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 3.6L V6 4.6L V8 Passenger Compartment Air Filter Particle and Odor Filter Particle Filter Spark Plugs 3.6L V6 4.6L V8...
Page 483: Engine Drive Belt Routing
Engine Drive Belt Routing 4.6L V8 Engine 3.6L V6 Engine...
Page 484: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 468. Any additional information from Owner Checks and Services on page 476 can be added on the following record pages.
Page 485 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II...
Page 486 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II...
Page 487: Customer Assistance Information
Section 7 Customer Assistance and Information ... 488 Customer Satisfaction Procedure ... 488 Online Owner Center ... 490 Customer Assistance for Text Telephone (TTY) Users ... 491 Customer Assistance Offices ... 491 GM Mobility Reimbursement Program ... 492 Roadside Service ... 493 Courtesy Transportation ...
Page 488: Customer Assistance And Information
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments.
Page 489 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 490: Online Owner Center
Online Owner Center Online Owner Center (United States only) The Owner Center is a resource for your GM ownership needs. Speciﬁc vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders. •...
Page 491: Customer Assistance For Text Telephone (Tty) Users
Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Cadillac encourages customers to call the toll-free number for assistance.
Page 492: Gm Mobility Reimbursement Program
Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 493: Roadside Service
New Vehicle Limited Warranty, up to a maximum coverage of $100. These services are provided at a nominal charge if the Cadillac is no longer covered by the warranties listed previously. Roadside Service is available only in the United States and Canada.
Page 494 Additional Services for Canadian Customers • Trip Routing Service: Upon request, Cadillac Roadside Service will send you detailed, computer-personalized maps, highlighting your choice of either the most direct route or the most scenic route to your destination,...
Page 495 (U.S. only) Cadillac’s exceptional Roadside Service is more than an auto club or towing service. It provides every Cadillac owner in the United States with the advantage of contacting a Cadillac advisor and, where available, a Cadillac trained dealer technician who can provide on-site service.
Page 496: Courtesy Transportation
Cadillac and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims become excessive in frequency or type of occurrence. Roadside Service is not part of or included in the coverage provided by the New Vehicle Limited Warranty.
Page 497 Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Participating dealers can provide you with shuttle service to get you to your destination with...
Page 498: Vehicle Data Collection And Event
Courtesy Transportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for speciﬁc information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. Canadian Vehicles: For warranty repairs during the Complete Vehicle Coverage period of the General Motors of Canada New Vehicle Limited...
Page 499 If your vehicle is equipped with StabiliTrak steering performance, including yaw rate, steering wheel angle, and lateral acceleration, is also recorded. This information has been used to improve vehicle crash performance and may be used to improve crash performance of future vehicles and driving safety.
Page 500: Collision Damage Repair
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualiﬁed technician using the proper equipment and quality replacement parts. Poorly performed collision repairs will diminish your vehicle’s resale value, and safety performance can be compromised in subsequent collisions.
Page 501 Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are signiﬁcant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
Page 502 • If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver’s name, the service’s name, and the phone number. • Remove any valuables from your vehicle before it is towed away.
Page 503 Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Page 504: Reporting Safety Defects
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors.
Page 505: Reporting Safety Defects To General Motors
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify us. Please call us at 1-800-458-8006, or write: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169 In Canada, please call us at 1-888-446-2000.
Page 506 Owner Information Owner publications are written speciﬁcally for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner Manual only.
Page 507 Accessories and Modiﬁcations ... 347 Accessory Power Outlet(s) ... 186 Adding Equipment to Your Airbag-Equipped Vehicle ... 88 Additives, Fuel ... 350 Add-On Electrical Equipment ... 454 Adjustable Throttle and Brake Pedal ... 120 Air Cleaner/Filter, Engine ... 365 Air Conditioning ... 189 Airbag Passenger Status Indicator ...
Page 508 Appearance Care (cont.) Tires ... 450 Underbody Maintenance ... 451 Vehicle Care/Appearance Materials ... 452 Washing Your Vehicle ... 447 Weatherstrips ... 447 Windshield and Wiper Blades ... 449 Wood Panels ... 447 Ashtray(s) ... 187 Audio System(s) ... 240 Audio Steering Wheel Controls ...
Page 509 Calibration ... 134 California Fuel ... 350 California Proposition 65 Warning ... 347 Canadian Owners ... 3 Capacities and Speciﬁcations ... 464 Carbon Monoxide ... 104, 132, 317, 331 Care of Safety Belts ... 447 Your CD Player ... 271 Your CDs ...
Page 510 Cleaning (cont.) Underbody Maintenance ... 451 Washing Your Vehicle ... 447 Weatherstrips ... 447 Windshield and Wiper Blades ... 449 Wood Panels ... 447 Climate Control System Air Filter, Passenger Compartment ... 195 Dual ... 189 Outlet Adjustment ... 194 Rear Air Conditioning System ...
Page 511 Daytime Running Lamps ... 179 Defensive Driving ... 274 Delayed Locking ... 102 Disc, MP3 ... 257 Diversity Antenna System ... 272 Doing Your Own Service Work ... 348 Door Central Door Unlocking System ... 101 Delayed Locking ... 102 Locks ...
Page 512 Engine Air Cleaner/Filter ... 365 Battery ... 385 Check and Service Engine Soon Light ... 208 Coolant ... 368 Coolant Heater ... 121 Coolant Temperature Gage ... 207 Coolant Temperature Warning Light ... 206 Drive Belt Routing ... 483 Engine Compartment Overview ... 356 Exhaust ...
Page 513 Fuel (cont.) Gage ... 213 Gasoline Octane ... 349 Gasoline Speciﬁcations ... 350 Fuses Fuses and Circuit Breakers ... 455 Rear Underseat Fuse Block ... 460, 462 Underhood Fuse Block ... 455 Windshield Wiper ... 454 Gage Engine Coolant Temperature ... 207 Fuel ...
Page 514 Horn ... 166 How to Use This Manual ... 4 How to Wear Safety Belts Properly ... 27 Ignition Positions ... 117 Infants and Young Children, Restraints ... 46 Inﬂation - Tire Pressure ... 407 Instrument Panel Overview ... 164 Instrument Panel (I/P) Brightness ...
Page 515 Light (cont.) Safety Belt Reminder ... 200 Security ... 212 TCS Warning Light ... 206 Tire Pressure ... 207 Tow/Haul Mode ... 213 Traction Control System (TCS) Warning ... 206 Lighting Entry ... 182 Parade Dimming ... 182 Limited-Slip Rear Axle ... 283 Loading Your Vehicle ...
Page 516 Mirrors Automatic Dimming Rearview ® with OnStar ... 134 Automatic Dimming Rearview ® with OnStar and Compass ... 134 Outside Automatic Dimming Mirror ... 138 Outside Convex Mirror ... 139 Outside Curb View Assist Mirror ... 138 Outside Power Heated Mirrors ... 137 MP3 ...
Page 517 Paint, Damage ... 451 Panic Brake Assist ... 284 Parade Dimming ... 182 Park Aid ... 184 Park (P) Shifting Into ... 129 Shifting Out of ... 131 Parking Assist ... 184 Brake ... 127 Over Things That Burn ... 131 Passenger Airbag Status Indicator ...
Page 518 Rear Door Security Locks ... 103 Rear Safety Belt Comfort Guides ... 39 Rear Seat Audio (RSA) ... 266 Rear Seat Entertainment System ... 266 Rear Seat Operation ... 18 Rear Seat Passengers, Safety Belts ... 36 Rear Windshield Washer/Wiper ... 172 Rearview Mirror, Automatic Dimming ®...
Page 519 Safety Belts (cont.) Rear Seat Passengers ... 36 Right Front Passenger Position ... 36 Safety Belt Extender ... 42 Safety Belt Use During Pregnancy ... 35 Safety Belts Are for Everyone ... 22 Safety Warnings and Symbols ... 4 Scheduled Maintenance ... 471 Seats Head Restraints ...
Page 520 Steering Wheel Controls, Audio ... 269 Steering Wheel, Tilt Wheel ... 166 Storage Areas Cargo Management System ... 155 Cell Phone Storage Area ... 154 Center Console Storage Area ... 154 Cupholder(s) ... 154 Glove Box ... 153 Luggage Carrier ... 154 Stowable Seat ...
Page 521 Tires (cont.) Tire Terminology and Deﬁnitions ... 404 Uniform Tire Quality Grading ... 419 Wheel Alignment and Tire Balance ... 420 Wheel Replacement ... 421 When It Is Time for New Tires ... 416 Winter Tires ... 400 Tow/Haul Mode ... 126 Tow/Haul Mode Light ...
Page 522 Warning Lights, Gages and Indicators ... 197 Warnings DIC Warnings and Messages ... 220 Hazard Warning Flashers ... 166 Other Warning Devices ... 166 Safety and Symbols ... 4 Vehicle Damage ... 5 Wheels Alignment and Tire Balance ... 420 Different Size ...

Cadillac 2007 SRX Owner's Manual

Table of Contents

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Cadillac 2007 SRX

Summary of Contents for Cadillac 2007 SRX