Spark Plug; Spark Arrester (Optional Part); Blade Control Check; Transporting - Honda HRN216VKU Owner's Manual

5. Wipe dirt from the inside of the air cleaner housing and cover
using a moist rag. Be careful to prevent dirt from entering the air
duct that leads to the carburetor.
6. Reinstall the filter and cover. Be sure both tabs are fully locked in
place.

Spark Plug

Replace the spark plug every 2 years or after 150 hours of use.
Required Spark Plug: NGK - BPR5ES
NOTICE
Using an incorrect spark plug can cause engine damage.
For good performance, the spark plug must be properly gapped and
free of deposits.
1. Allow the engine to cool,
disconnect the spark plug
cap, and remove any dirt
from around the spark
plug area.
2. Remove the spark plug
with a 21 mm spark plug
wrench.
3. Inspect the spark plug.
Replace it if the
electrodes are worn, or if
the insulator is cracked or
chipped.
4. Measure the spark plug
electrode gap with a
suitable gauge.
Gap:0.7 ~ 0.8 mm
Correct the gap, if
necessary, by carefully
bending the side
electrode.
5. Install the spark plug
carefully, by hand, to
avoid cross-threading.
6. After the spark plug
seats, tighten with a
21 mm spark plug wrench to compress the washer.
If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the
spark plug seats.
If installing a new spark plug, tighten 1/2 turn after the spark plug
seats.
Spark plug torque: 20 N·m
NOTICE
A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the
cylinder head.
7. Install the spark plug cap on the spark plug.

Spark Arrester (optional part)

The spark arrester must be serviced every 100 hours to keep it
functioning as designed.
Your lawn mower engine is not factory-equipped with a spark arrester.
In some areas, it is illegal to operate an engine without a spark
arrester. Check local laws and regulations. An optional USDA
approved spark arrester is available from an authorised Honda
servicing dealer. See "Parts, Accessories, and Service Items" on
page 20 for the part number.
14
SPARK PLUG
SPARK
PLUG
CAP
0.7 ~ 0.8 mm
SEALING
WASHER
1. Allow the engine to cool.
2. Unclip the two red top cover tabs [6] on the muffler side of the
engine, and then slightly lift the red top cover up to expose the
upper muffler shield bolt.
3. Remove the three bolts [1] from the muffler shield [2] using a
10 mm socket wrench.
4. Remove the muffler shield [2].
5. Remove the set screw [4].
6. Remove the spark arrester [3] from the muffler [5].
7. Check for carbon deposits on the spark arrester and the exhaust
port. Brush carbon deposits away. Be careful to avoid damaging
the spark arrester screen.
8. Install the spark arrester into the muffler.
9. Install the muffler components on the engine, and tighten the three
bolts securely.
[4]
[1] (3)
[2]

Blade Control Check

1. Start the engine outdoors.
2. Release the blade control
lever; the engine should stop
quickly.
If it does not, take your
mower to an authorised
Honda servicing dealer for
repair.

TRANSPORTING

If the engine has been running, allow it to cool before loading the
mower on the transport vehicle. A hot engine and exhaust system can
burn you and can ignite some materials.
Turn the fuel valve to the OFF position. This will prevent carburetor
flooding and reduce the possibility of fuel leakage.
If installed, remove the grass bag.
If a suitable loading ramp is not available, two people should lift the
mower on and off the transport vehicle while holding the mower level.
Position the mower so all four wheels are on the bed of the transport
vehicle. Tie the mower down with rope or straps, and block the
wheels. Keep the tie-down rope or straps away from the controls,
adjustment levers, cables, and the carburetor.
Fold the handlebar so the mower will take up less space
[6]
[3]
[5]
(red cover shown removed)
BLADE CONTROL
LEVER
(page 15).