Related Manuals for Edimax IC-1520DP
Summary of Contents for Edimax IC-1520DP
- Page 1 IC-1520DP / IC-1520DPg / IC-1520POE Wire / Wireless / Power over Ethernet Digital Pan/Tilt Internet Camera Quick Installation Guide Version: 1.0 (October, 2007)
- Page 2 Multi-Languages QIG on the CD Č ý : Českého průvodce rychlou instalací naleznete na přiloženém CD s Č ý ovladači : Finden Sie bitte das deutsche S.A.L. beiliegend in der Treiber CD ñ l : Incluido en el CD el G.R.I. en Español. ñ...
-
Page 3: Table Of Contents
1. Check your package contents ... 1 1.1. System Requirement ... 2 2. Hardware Installation ... 2 2.1. LED and Focusing ... 2 2.2. Installation Procedure ... 5 2.3. Locate the IP Address... 6 3. Web Management Interface... 10 4. Software Installation... 13 4.1 Firmware Upgrade... - Page 4 Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this Company .
-
Page 5: Check Your Package Contents
IC-1520POE is a wire internet camera with power over Ethernet function . Check your package contents Thank you for purchasing Edimax IP camera! Before you start to use this IP camera, please check the package contents. If anything is missing, please contact the dealer of purchase and return the package to claim for missing contents. -
Page 6: System Requirement
1.1. System Requirement System requirement for PC, MAC or Notebook PC to access the Internet Camera are: OS System: Windows 98, ME, 2000, XP + SP2, Server 2003 CPU: Intel Pentium III 750MHz above or Intel Celeron 1GHz above Memory Size: 128MB (256MB recommended) VGA Card Resolution: 800 x 600 or above Hardware Installation 2.1. - Page 7 Power When the camera is power on and ready for access, the LED will light. When the Internet Camera is linking to wired network, the LED is lighting. The LED is flashing when video is transmitted or received through wired network. WLAN ( For IC-1520DPg only ) When the Internet Camera is linking to wireless network, the LED is lighting.
- Page 8 The Camera features two ports and a Reset button. Antenna Standard reverse SMA connector where any antennas with reverse SMA connector can connect to the Internet Camera. Power The Power jack is where you can connect the power adapter. The LAN jack is where you can connect the Ethernet network cable. Reset If problems occur with your Internet Camera, press the reset button with a pencil tip (for less than 2 seconds) and the Internet Camera will reboot itself...
-
Page 9: Installation Procedure
2.2. Installation Procedure 1. Unpack the Internet Camera package and verify that all the items listed in the Chapter 1 are provided. 2. Connect the Internet Camera to your network by attached the network cable from the switch/router to the LAN port of the Internet Camera. 3. -
Page 10: Locate The Ip Address
2.3. Locate the IP Address Default IP address of this IP camera is 192.168.2.3. If you wish to assign another IP address to this IP camera, you have to log onto the web configuration interface of the camera first. If the left three fields of the IP address of your computer is not 192.168.2.XXX , you’ll have to change the IP address of your computer first: 1. - Page 11 2. Double-click ‘Network Connections’ icon. 3. Right-click ‘Local Area Connection’, and click ‘Properties’.
- Page 12 4. Select ‘Internet Protocol (TCP/IP)’, then click ‘Properties’.
- Page 13 5. In ‘IP address’ field, please fill in any IP address begins with ‘192.168.2’, and ends with a value greater than 2 and less than 254 (You can use the example in the picture ‘192.168.2.239’). In Subnet mask field, please fill ‘255.255.255.0’. Please keep all other fields empty, and click ‘OK’.
-
Page 14: Web Management Interface
Web Management Interface Make sure the IP camera is correctly powered (Power LED is on), and then launch Internet Explorer and type the IP address of the IP camera in address bar of Internet Explorer. You should be prompted to input the user name and password: Default user name is ‘admin’... - Page 15 This IP camera requires a special ActiveX control (A.K.A. ‘Plugin’) to work. Please click on the message, and select ‘Install ActiveX Control…’: When you’re prompted, click ‘Install’ to continue.
- Page 16 You should be able to see the image from camera now: Note: If you see one of these messages (or both): Your computer may not have the display capability that this IP camera requires, or you don’t have Microsoft DirectX® installed. Please download Microsoft DirectX® from Microsoft’s website (http://www.microsoft.com), and try again.
-
Page 17: Software Installation
Software Installation Follow the simple steps below to run the Install Wizard to guide you quickly through the Installation process. The following installation is implemented in Windows XP. The installation procedures in Windows 2000/XP/Server 2003 are similar. 1. Insert the CD shipped along with the Internet Camera into your CD-ROM drive. The “Autorun.exe”... - Page 18 3. The system will start the installation procedures. Click “Next” to continue installation. 4. If you wish to install the software program in an alternate location, click “Change”; otherwise click “Next” to move on to the next step.
- Page 19 5. Click “Install” to start installing the program. 6. The system will install the program automatically.
- Page 20 7. Click “Finish” to complete the software installation. If you have Windows Defender (Windows XP) or other 3 party firewall software, you may see the following (or similar) message: Please click ‘Unblock’ (or similar option) to let IP camera Utility pass the firewall, or the IP camera utility may not be able to function properly...
- Page 21 A new folder named ‘IP Camera’ in ‘All Programs’ will be created: Admin Utility, Camera Viewer, and Uninstall. You can use these 3 utilities to connect to the IP camera and use the functions of the camera without web browser.
- Page 22 10. When the installation is completed. The system will auto run ”Administrator Utility“. On the Internet Camera first page, the cameras found in the network are listed in the left window. Choose the one you want to configure and click “Setting Wizard” to proceed.
- Page 23 11. Internet Camera is working through the network (TCP/IP Protocol). The IP address setting must be correct, or you cannot access to the camera. The wizard program will detect the IP address status of your network automatically and suggest a free IP address for the Camera. You can accept the suggested value or enter the value manually.
- Page 24 13. The “Camera Viewer” will show the video automatically. Congratulations, you can use the camera through the network to view the video from now on.
-
Page 25: Firmware Upgrade
4.1 Firmware Upgrade Here provides several tools to upgrade the firmware of this IP camera, clear all settings, or switch LED notification off. - Page 26 The descriptions of every setting in this menu will be given below: Item Description Upgrade If you downloaded latest firmware file from our Firmware website, you can click this button to start to upload the firmware file to the IP camera, and you’ll be prompted to provide the location of firmware file.
- Page 27 R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.