Related Manuals for A&D AD-1191
Summary of Contents for A&D AD-1191
- Page 1 AD-1191 Instruction Manual Printer for A & D Scales & Balances Part #: I-MAN:1191A&D-USA Revision 1.0 • June 20, 2000...
- Page 2 CAUTION Risk of electrical shock. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. A&D Weighing reserves the right to change specifications at any time.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction ... 1 Installation ... 1 Installing the Paper ... 1 To Remove the Paper Roll ... 4 Operation ... 5 Connecting and Powering up Your Printer ... 5 Maintenance ... 5 Changing the Printer Ribbon ... 6 Inserting a Ribbon with Paper in the Printer ... - Page 4 Specifications Interface Interface- - - - - Serial Interface Serial Serial Serial Interface Interface Serial Available baud rates: Voltage levels: Character format: 1.5K standard Character Buffering Character Buffering Character Buffering Character Buffering Character Buffering 8K optional Approximately 9500 byte capacity with option installed. P P P P P rint Method rint Method rint Method...
- Page 5 P P P P P rint Head Life rint Head Life rint Head Life rint Head Life 500,000 lines mean character before failure. rint Head Life Ribbon life Ribbon life Ribbon life Ribbon life Ribbon life Black- 200,000 characters Purple-250,000 characters P P P P P aper aper aper...
-
Page 6: Introduction
Introduction Installation Follow the precautions listed below when setting up your Installing the P Installing the Paper Installing the P aper aper aper Installing the P Installing the P aper printer. They are designed to help you keep your printer working at its best. - Page 7 This will facilitate the entry of the paper into the printer. Slide the paper through the slot connecting the paper compartment and the printer compartment. You can slide it in about one-quarter inch before it stops. While holding the paper in place, press the rocker switch to the Paper Feed position.
- Page 8 10. Push the back of the printer cover down and into 11. Press the front of the printer cover down to lock in 12. Put the paper spindle into the paper roll as shown 3 3 3 3 3 place. place.
-
Page 9: To Remove The Paper Roll
T T T T T o Remove the P o Remove the P o Remove the P aper aper o Remove the P o Remove the Paper aper aper Roll Roll Roll Roll Roll Advance the paper about one inch beyond the paper cutter by using the Paper Feed switch. -
Page 10: Operation
Operation Connecting and Connecting and Connecting and Connecting and Connecting and P P P P P owering Up owering Up owering Up owering Up owering Up Y Y Y Y Y our P our P our P rinter rinter our P our Printer rinter rinter... -
Page 11: Changing The Printer Ribbon
Changing the P Changing the P rinter rinter Changing the P Changing the Printer Changing the P rinter rinter If your printer is used infrequently, the print impression Ribbon Ribbon Ribbon Ribbon Ribbon may become weak because the ribbon has dried out. To advance the ribbon to a new section, hold down the Paper Feed switch for several seconds. -
Page 12: Inserting A Ribbon With Paper In The Printer
If you get ribbon ink on the printer case, wipe it off immediately. Once it dries it is difficult to remove. 7 7 7 7 7 Install new cartridge. Be sure the ink cartridge is inserted firmly to prevent weak or irregular printing. The cartridge must be properly seated and aligned for best printing. -
Page 13: Printer Test And Setup
Printer Test and Setup The printer can be tested and setup using the steps described in this section. Testing and setup are done using the rocker switch on the printer. With the printer unplugged at the outlet or at the back of P P P P P rinter T rinter T rinter T... -
Page 14: Accessing The Setup Menu
Accessing the Setup Accessing the Setup Accessing the Setup Accessing the Setup Accessing the Setup To access the setup menu follow these steps: Menu Menu Menu Menu Menu If you wait less than three or more than five seconds R R R R R eady again to access the setup menu. - Page 15 With the printer in the setup menu and with CONFIGURE CONFIGURE CONFIGURE CONFIGURE CONFIGURE OK (right side) to access the CONFIGURE following is printed: L L L L L OAD DEF Load Defaults Load Defaults Load Defaults Load Defaults Load Defaults printer to all default settings (shown below).
- Page 16 P P P P P arity arity arity arity Parity can be selected only if 7 data bits are set. Choose arity Odd or Even. If you choose 8 data bits, parity defaults to None. Stop Bits Stop Bits Stop Bits ST ST ST ST STOP BITS Stop Bits Stop Bits...
-
Page 17: Custom
DOUBLE HIGH DOUBLE WIDE/HIGH After you choose one of the magnifications the printer will print R R R R R eady eady eady eady eady to show the printer is out of the configuration menu and the setup menu and is ready to print. CUST CUST CUSTOM... - Page 18 T/D Format T/D Format T/D Format T/D Format T/D Format Auto T&D Auto T&D Auto T&D Auto T&D Auto T&D Auto Seq# Auto Seq# Auto Seq# Auto Seq# Auto Seq# Zero Zero Zero Zero Zero P P P P P ound Sign ound Sign ound Sign ound Sign...
-
Page 19: Set Clock
Online/Offline Online/Offline Online/Offline Online/Offline Online/Offline ONLINE/OFFLINE ONLINE/OFFLINE ONLINE/OFFLINE ONLINE/OFFLINE ONLINE/OFFLINE is next. Choices: Ext Ch Set Ext Ch Set Ext Ch Set Ext Ch Set Ext Ch Set EXT CH SET EXT CH SET is next. This stands for Extended Character Set. EXT CH SET EXT CH SET EXT CH SET... -
Page 20: Reset Seq
The cursor now appears over the 2nd position. Press This feature is NEXT NEXT NEXT NEXT (left side) to increment this number if needed and NEXT available only on OK if it is right. Continue this sequence of accepting or units with the changing the year, month, day, and DOW (Day Of Week). -
Page 21: Communication
Communication Pin No. Pin No. Signal Signal Pin No. Pin No. Pin No. Signal Signal Signal Chassis ground (TD) Transmitted data (RD) Received data (SG) Signal (CTS) Clear to send The rest are not used. DTE Direction DTE Direction Description Description DTE Direction DTE Direction... -
Page 22: Control Codes
CONTROL CONTROL CONTROL CONTROL CONTROL According to the American Standard Code of Information Interchange (ASCII), there are 32 control codes in addition CODES CODES CODES CODES CODES to the codes for the printable characters. (Control codes are sent as data, but the receiving device interprets them as abbreviated ‘’instructions”, communication - status messages, etc.) The printer recognizes these control codes:... - Page 23 Back Space Back Space Back Space Back Space Back Space Upon receipt of this code, the printer erases from its Code 8 Code 8 Code 8 Code 8 Code 8 buffer the previously received character. This is useful in correcting typing errors for programs that send data both to a video screen and the hardcopy printer.
- Page 24 Enlarged P Enlarged P rinting rinting Enlarged Printing Enlarged P Enlarged P rinting rinting Enlarged printing may be selected by sending both the Codes 14 and 15 Codes 14 and 15 Codes 14 and 15 Codes 14 and 15 Codes 14 and 15 double height command (control code 14) and the double width command (control code 15).
- Page 25 Dot Graphics Dot Graphics Dot Graphics Dot Graphics Dot Graphics The mechanism used in the printer prints one line of dots Code 18 Code 18 Code 18 Code 18 Code 18 across at a time. This means that when it prints one line of characters it has actually printed ten lines of dots where the first eight lines make up the character and the last two lines are blank for the space between character...
- Page 26 User Programmable User P User P rogrammable rogrammable rogrammable User P User P rogrammable Character Character Character Character Character Code 19 Code 19 Code 19 Code 19 Code 19 2 1 2 1 Example 1: Example 2: By using CHR$(19) you enter the Custom Character mode.
- Page 27 Use quad ruled paper to design your character. Number 8 consecutive rows like this: Now design your character in dot form (see the example below). Add together all the numbers from the column on the left, counting only where you have placed a dot in a row.
- Page 28 Set Time and Date Set Time and Date Set Time and Date Set Time and Date Set Time and Date Control Code 20 Control Code 20 Control Code 20 Control Code 20 Control Code 20 Read Time and Date Read Time and Date Read Time and Date Read Time and Date Read Time and Date...
- Page 29 Access Memory). The section on USER Programmable Character describes how this RAM can be loaded with any 6 x 8 pattern. The model AD-1191 also has a graphic character set that resides between hexidecimal values 80 and FF (decimal 128 and 255).
- Page 30 C o m m a n d C o m m a n d P P P P P rinter Escape rinter Escape rinter Escape rinter Escape C o m m a n d Print formatted data C o m m a n d C o m m a n d rinter Escape Command Code...
-
Page 31: Default Table
Default Table Below is a table showing the possible values for the Custom and Configuration menu parameters. The values shown in bold Custom Menu Custom Menu Custom Menu Custom Menu Custom Menu T/D Format 1 - None 2 - MM/DD/YY_hh:mm_?M 3 3 3 3 3 - - - - - MM/DD/YY hh:mm ?M DOW MM/DD/YY hh:mm ?M DOW MM/DD/YY hh:mm ?M DOW... - Page 32 Notes...
-
Page 33: Warranty And Service Information
Warranty and Service Information Seller warrants that the AD-1191 will conform to written specifications, drawings, and other descriptions made by the manufacturer, including any modifications thereof. The Seller warrants the goods against faulty workmanship and defective materials. If any goods fail to conform to these warranties, Seller will, as its sole... - Page 34 1555 McCandless Drive, Milpitas, CA 95035 · Tel: (800) 726-3364 / (408) 263-5333 · Fax: (408) 263-0119 Fax-on-Demand: (800) 726-7099, press 2 · Email: andweighing.com · Web: www.andweighing.com...