Black Max BM31FB01 User Manual

FOAMER NOZZLE ATTACHMENT
BM31FB01
WARNING:
To reduce the risk of injury, user must read and under-
stand the operator's manual for their pressure washer
before using this accessory. To reduce the risk of injury
or property damage, spray the pressure stream in a safe
direction to ensure proper connection of all accessories
before starting any cleaning project. Fits most pressure
washers. Ensure compatibility and proper fit before us-
ing this accessory. Wear eye protection with side shields
marked to comply with ANSI Z87.1. Risk of fluid injec-
tions; do not point at people, pets, electrical devices
or the unit itself. Turn off the pressure washer before
changing or adjusting accessories. For cold water use
only. For outdoor use only – store indoors. Save these
instructions. Refer to them frequently and use them to
instruct other users. If you loan someone this tool, loan
them these instructions also.
PRODUCT SPECIFICATIONS
Connection ....................... 1/4 in. Quick Connect Plug Inlet
Maximum Pressure ....................................... up to 3800 psi
Detergent Cup Capacity .............................................34 oz.
Maximum Water Flow ............................................... 3 GPM
Maximum Water Temperature .................................... 140°F
APPLICATIONS
You may use this product for the purpose listed below:
n Applying detergent to remove dirt and mold from decks,
cement patios, and house siding, cars, boats, motor-
cycles, outdoor furniture, and grills
INSTALLING THE FOAMER NOZZLE
ATTACHMENT
See Figures 1 - 2.
The foamer nozzle attachment allows you to use foaming
detergent while using your pressure washer for cleaning.
n Add all of the included detergent to the detergent cup
and fill with water. For other detergents, use as directed
by the detergent's instructions.
NOTE: Use concentrated foaming detergent (available at
your local retailer) in the attachment. Any other solutions
may damage the attachment.
n Install the attachment head to the cup and tighten to lock
in place.
0 0
0
1
0
0
9
0 0
8
7 0 0
6 0 0
5 0 0
4 0 0
3 0 0
2 0 0
1 0 0
ATTACHMENT
HEAD
SIPHON
TUBE
DETERGENT
CUP
0 0
0
1
0
0
9
Fig. 1
0 0
8
7 0 0
6 0 0
5 0 0
4 0 0
3 0 0
2 0 0
1 0 0
PRESSURE
WASHER
SPRAY
WAND
0 0
0
1
0
0
9
Fig. 2
0 0
8
n Install the attachment on the end of your pressure wash-
er's spray wand just as you would any type of nozzle.
USING THE FOAMER NOZZLE ATTACHMENT
See Figures 3 - 4.
WARNING:
Do not make adjustments while using the pressure
washer. Stop spraying and lock out the trigger before
making adjustments. Keep hands away from nozzle tip
when spraying.
n The amount of detergent in the spray is controlled by the
detergent flow knob.
• Rotate knob fully clockwise to use the detergent at its
highest concentration.
• Rotate knob fully counterclockwise to use the detergent
at its lowest concentration.
n The foamer nozzle sprays in a fan or stream pattern that
can be adjusted by turning the nozzle.
When finished:
n Remove the detergent cup from the foamer nozzle and
rinse the cup with water to remove any detergent residue.
n Fill the cup with water, then reinstall.
n Spray the full cup of water through the foamer nozzle to
clean any detergent residue from inside the nozzle.
n Remove the foamer nozzle attachment from the spray
wand.
n Rinse the outside of the foamer nozzle attachment com-
pletely to remove any detergent residue. Allow all parts
to dry completely before storing.
n For outdoor use only – store indoors.
Model/item number on product may have additional letters at the end.
These letters designate manufacturing information and should be pro-
vided when calling for service.
Hart Consumer Products, Inc.
Anderson, SC 29622, USA
www.blackmaxtools.com
LESS MORE
FOAM FOAM
DETERGENT
FLOW KNOB
FAN
POSITION
STREAM
POSITION
P.O. Box 1348
1-800-726-5760
0 0
0
Fig. 3
1
0
0
9
0 0
8
7 0 0
6 0 0
5 0 0
4 0 0
3 0 0
2 0 0
1 0 0
0 0
0
1
0
0
9
0 0
8
7 0 0
6 0 0
5 0 0
4 0 0
3 0 0
2 0 0
Fig. 4
1 0 0
0 0
0
1
0
0
9
998000076
0 0
8
10-29-20 (REV:03
7 0 0