Environmental Protection; Maintenance - Ryobi R18PDBL Original Instructions Manual

product – Wear suitable protection depending on type
of dust.
RIsK ReductIOn
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARnInG
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KnOW YOuR PROduct
See page 5.
1. Keyless chuck
2. E-TORQUE indicator
3. Hammer/Drill/Screw driving
E-TORQUE selector
4. Two-speed gear train
5. Forward/ reverse button
6. Switch trigger
7. LED light
8. Screw driver bit
9. Bit storage
10. Battery port
11. Handle, insulated gripping surface

MAIntenAnce

WARnInG
The product should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.
■
■
■
■
■
LuBRIcAtIOn
All of the bearings in the product are lubricated with a
sufficient amount of high grade lubricant for the life span of
the product under normal operating conditions. Therefore,
no further lubrication is required.

enVIROnMentAL PROtectIOn

e-tORQue cOntROL
E-TORQUE CONTROL helps regulate the power output
of the product to avoid over-driving screws and damaging
mode selector and
materials. To achieve a flush finish, it is best to select a
low setting before commencing screw driving. When the
E-TORQUE CONTROL engages, the E-TORQUE selector
LED and E-TORQUE indicator LED will flash and the
product will automatically shut down.
If more power is required to drive the screw flush, the
E-TORQUE CONTROL can be adjusted accordingly.
E-TORQUE CONTROL only operates in screw driving
mode, it has no effect on drilling mode.
The product has a memory function that stores torque
settings. When switching from drilling to screwdriving
mode, the memory function restores previously used torque
settings. The E-TORQUE selector and indicator LEDs will
flash once previously used torque setting is reached.
When servicing, use only original manufacturer's
replacement parts. Use of any other parts may create a
hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt and carbon dust.
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken or destroy plastic.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
For greater safety and reliability, all repairs should be
performed by an authorised service centre.
Recycle raw materials instead of disposing
of as waste. The machine, accessories and
packaging should be sorted for environment-
friendly recycling.
Safety
3