Related Manuals for Woods Alitec AB720-2, Alitec AB840-2
Summary of Contents for Woods Alitec AB720-2, Alitec AB840-2
- Page 1 ANGLE BROOM AB720-2, AB840-2 AB720-2 S/N 1187272 And Before AB720H-2 S/N 1240349 And Before AB840-2 S/N 1237452 And Before AB840H-2 S/N 1240351 And Before...
-
Page 2: Introduction
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces... -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION..........2 GENERAL INFORMATION . -
Page 4: General Information
GENERAL INFORMATION The purpose of this manual is to assist you in oper- The illustrations and data used in this manual were cur- ating and maintaining your angle broom. Read it rent at the time of printing, but due to possible inline carefully. -
Page 5: Safety Rules
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Hydraulic fluid under pressure can easily penetrate Safety is a primary concern in the design and skin and will cause serious injury or death. manufacture of our products. Unfortunately, our Make sure that all operating and service person- efforts to provide safe equipment can be wiped nel know that if hydraulic fluid penetrates skin, it out by an operator’s single careless act. - Page 6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Always wear relatively tight and belted clothing Keep brush away from intense heat or flame. to avoid getting caught in moving parts. Wear Brush material can ignite and burn.
- Page 7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- Your dealer can supply original equipment ator's Manual instructions for working underneath hydraulic accessories and repair parts.
-
Page 8: Safety Decals
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - SERIAL NUMBER PLATE 3 - PN 1016019 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 2 - PN 1016017 4 - PN 1015363 8 Safety MAN0731 (9/19/2008) - Page 9 Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.
-
Page 10: Operation
OPERATION ATTACH ANGLE BROOM TO SKID STEER The operator is responsible for the safe operation of this equipment. Operators must be instructed in and be Read the skid steer operator's manual connecting and capable of the safe operation of the equipment, its removing instructions. - Page 11 3. Place a bubble level on the swing assembly and level the brush front to back using the skid steer. 4. Set parking brake and shut off skid steer. 5. On each side, measure from the brush frame to the ground.
- Page 12 OPERATION Read and understand the angle broom and skid steer operator's manuals before operating the angle broom. Failure to do so may result in death, serious personal injury or property damage. Never raise the angle broom more than a few inches off the ground when traveling from job site to job site.
- Page 13 Manual Angle Broom Low brush speeds and moderate ground speeds work best for cleaning debris from hard surfaces. Brush 1. Remove the lock pin from the swing assembly. speeds that are too fast tend to raise dust because of the aggressive sweeper action. 2.
- Page 14 NOTICE Set brake, shut off engine, remove key, remove seat belt and release operator restraint before leaving the ■ skid steer operator's seat. Do not store the broom with weight on the brushes. Weight will deform them, destroying the Disconnect hydraulic hoses from quick couplers. Install sweeping effectiveness.
-
Page 15: Owner Service 15
OWNER SERVICE Make sure that all operating and service person- The information in this section is written for operators nel know that if hydraulic fluid penetrates skin, it who possess basic mechanical skills. Should you need must be surgically removed as soon as possible by help, your dealer has trained service technicians avail- a doctor familiar with this form of injury or gan- able. - Page 16 Hydraulic fittings and hoses, tighten ● Sand down scratches and the edges of areas of ✔ Grease fittings missing paint and coat with Woods spray paint of matching color (purchase from your Woods ✔ Check hydraulic fluid level dealer). ✔...
-
Page 17: Troubleshooting 17
Contact hose manufacturer for proper maximum rate of broom. flow control method. Hydraulic motor seals leak. Back pressure exceeds 1000 PSI. Contact Woods Technical Support. Motor is failing. High number of hours on motor; contact dealer to rebuild or replace. Troubleshooting 17... -
Page 18: Dealer Service
DEALER SERVICE sturdy, rough-soled work shoes and protective The information in this section is written for dealer ser- vice personnel. The repair described here requires equipment for eyes, hair, hands, hearing, and head; special skills and tools. If your shop is not properly and respirator or filter mask where appropriate. - Page 19 Assemble Unit 1. Attach the section retainer and bearing mounting plate with previously removed hardware. 2. Lay core on the ground. Lower frame over core. 3. Attach bearing mounting plate with previously removed hardware. 4. Attach motor mount with hardware previously removed.
-
Page 20: Dealer Check List
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY Inspect the equipment thoroughly after assembly to ___ Show customer how to make adjustments. ensure it is set up properly before delivering it to the ___ Instruct customer how to lubricate and explain customer. -
Page 21: Parts Lists
PARTS INDEX Angle Broom AB720-2 & AB840-2 BRUSH HEAD FRAME ASSEMBLY ........22 CORE ASSEMBLY . - Page 22 BRUSH HEAD FRAME ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 1015343 Chain, 1/4 x 22 1015328 Plate mtg brush head pivot 1015335 Screw, M6-1 X 20 mm HFH CL10.9 10 1015338 Sheet hood side left 1015334 Link quick 5/16 11 1015337 Sheet hood side right 1015333 Nut insert M6 - 1.0...
- Page 23 CORE ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 1016026 Section, set 32, poly convoluted (6 ft) 1015335 Screw, M6-1 X 20 mm HFH CL10.9 1015353 Section, set 32, poly convoluted (7 ft) 1015333 Nut insert M6 - 1.0 1016025 Section, set 32, mixed convoluted (6 ft) 1015341 Plate, ring, core end QC Weld core 6 ft hex drive -or-...
- Page 24 SHAFT ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 31813 M10-1.5 x 35 mm HHCS, CL8.8 1016044 Nut, hex M10-1.5 1016049 * Washer lock split M8 1015342 Bearing, 1-1/4 x 4 bolt 1016048 * Washer flat CL8.8 M10 1016043 Washer, .34 X 1.8 X 10 ga 1016047 * 14 Washer lock split M10 10 1016042...
- Page 25 HYDRAULIC ASSEMBLY, SINGLE MOTOR PART DESCRIPTION PART DESCRIPTION 1026715 Hose, 80" x 10 FFS x 12 ORBM 1026719 Weld plate F / .88 OD 54546 Adapter, 7/8 ORBM, 5/8 MFS 1015375 Cover plate F / .88 OD 1016004 Adapter, 10 FOR x 10 FOR 1015372 Hose cradle F / .88 OD 1026716...
- Page 26 MOTOR BUCKET ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 1015347 Motor, hyd 24.9 cu. in w/check 1016037 M12-1.75 X 35 mm SHCS CL12.9 1A 1036271 Seal kit, motor 1015340 Weld motor bucket 1016048 * Washer, flat M10 1026733 Hub hex, 2-1/2 x 1-1/4 tapered 1016047 * 10 Washer, lock split M10 10 1015350...
- Page 27 QUICK ATTACH REF PART DESCRIPTION REF PART DESCRIPTION 33034 * Bolt, carriage, 5/8 NC x 1-3/4 GR5 1026721 Pin, quick release 1 x 3 230 * Nut, hex 5/8 NC 54617 Weld plate swing 54603 Chain, 1/4 x 21 links 10 1026722 Weld frame 1286 *...
- Page 28 HYDRAULIC ANGLE ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION 54546 Adapter, 7/8 ORBM x 5/8 MFS 90003054 M8 x 1.25P x 30 mm HHCS CL10.9 1026730 Adapter, 3/8 MFS x 9/16 ORBM 14 1026717 M8 x 1.25P Hex lock nut 1026729 Hose, 32"...
-
Page 29: Quick Coupler Charts
QUICK COUPLER KITS High-Flow with Auxiliary High-Flow with No Auxiliary Low-Flow Make QC Kit Description QC Kit Description QC Kit Description Bobcat HC356 Flush Face HC355 Flush Face HC357 Flush Face HC243 Poppet HC211 Ag Ball Valve Case 1013825 Flush Face HC212 Flush Face HC279... - Page 30 QUICK COUPLER KIT COMPONENTS QC KIT Includes Style Male/Female Size Hose End HC308 HC416 Flush Face Female SAE #12 O-ring HC417 Flush Face Male SAE #12 O-ring HC418 Flush Face Male SAE #8 O-ring HC310 HC414 Flush Face Male SAE #12 O-ring HC415 Flush Face Female...
- Page 31 QUICK COUPLER KIT COMPONENTS QC KIT Includes Style Male/Female Size Hose End 1013834 HC414 Flush Face Male SAE #12 O-ring HC415 Flush Face Female SAE #12 O-ring HC521 Flush Face Female 16 mm SAE #12 O-ring HC522 Flush Face Male 16 mm SAE #12 O-ring 1013835...
-
Page 32: Hydraulic Fitting Torque Chart
FITTING TORQUE CHART Always tighten fittings to these values unless a different torque value is listed for a specific service procedure. Make sure fastener threads are clean and threads are engaged properly. All torque values are adopted from SAE J514 and SAE J1453. SAE (JIC) O-Ring Style Seal-Lok... -
Page 33: Bolt Torque Chart
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 34: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa ............Mega Pascal ASABE ....American Society of Agricultural &... - Page 35 BW180XHD, BW1260X, BW1800X, BW240, BW240HD, DS1260, DSO1260, DS1440, TS1680 Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
- Page 36 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.