Linear MULTI-CODE 3083 Installation Instructions

INSTR,INSTL,MC3083,2 BTN MINI-TX PN: 214944 Rev-C, INK: Black, MATERIAL: 20 LB, MEAD BOND, SIZE: 9.500" X 4.600", SCALE: 1-1
PLEASE NOTE
Nortek Security & Control has devoted a great deal of time and research in
order to provide the most reliable equipment possible. Certain limitations
must be observed.
1) MULTI-CODE radio components must conform with FCC Part
15 requirements. For this reason, the range and power of our
radios is within specified limits.
2) As with all manufacturers, Nortek Security & Control's radios
must accept all signals that they receive. This may, in rare
instances, create difficulty.
3) You should test your entire system occasionally in order to be
sure that all components are working in good order.
4) Nortek Security & Control's dealers can provide you with
information regarding the use of our radio controls, and can
provide valuable installation and operation information, when
requested.
WARNING: Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the Federal
Communications Commission (FCC) rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
5
PRINT INSTRUCTIONS:
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC & IC Notice
This device contains licence-exempt transmitter(s) / receiver(s) that
comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d'Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
1. L'appareil ne doit pas produire de brouillage;
2. L'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
USA & Canada Toll Free (800) 421-1587
or dial (760) 438-7000
www.nortekcontrol.com
6
®
INSTALLATION INSTRUCTIONS
MODEL 3083
TWO CHANNEL MINI-TRANSMITTER
Congratulations! You have just purchased a Multi-Code
Digital Transmitter, which we believe to be the finest product
of its kind on the market. With a little care this transmitter
should provide you with many years of excellent service.
Please take a moment to read the following instructions
and you will find that setting your new transmitter will be
quite an easy matter.
ACCESSING THE CODE SWITCH AND BATTERY
COMPARTMENT
The model 3083 two channel Mini-transmitter case is
composed of 2 halves which are held together by a small
phillips head screw. Removing this screw will allow access
to the code switches and the battery compartment (see
Diagram #1, below).
BATTERY
LED
TRANSMITTER WITH TOP
HALF OF CASE REMOVED
CODE SWITCH #1
CODE SWITCH #2 TRANSMITTER TOP COVER
DIAGRAM #1
1