Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCD731
Summary of Contents for DeWalt DCD731
- Page 1 DCD731 DCD734 DCD771 DCD776 FINAL PRINT SIZE: A5 (148mm x 210mm)
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Figure 1 DCD771 Figure 2...
- Page 4 Figure 3 Figure 4 Figure 5 Figure 6 DCD776 Figure 7 Figure 8 Figure 9...
-
Page 5: Technical Data
English CORDLESS COMPACT 10 mm (3/8"), 13 mm (1/2") DRILL/DRIVER/HAMMERDRILL DCD731, DCD734, DCD771, DCD776 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. -
Page 6: Definitions: Safety Guidelines
English WARNING: The declared vibration Charger DCB107 emission level represents the main Mains voltage applications of the tool. However if the Battery type 10.8/14.4/18 Li-Ion tool is used for different applications, with different accessories or poorly Approx. charging min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah) maintained, the vibration emission may time of battery 140 (3.0... -
Page 7: Ec Declaration Of Conformity
(grounded) power tools. Unmodified plugs DRILL/DRIVER/HAMMERDRILL and matching outlets will reduce risk of DCD731, DCD734, DCD771, DCD776 electric shock. Avoid body contact with earthed or WALT declares that these products described grounded surfaces such as pipes, under Technical Data are in compliance with: radiators, ranges and refrigerators. - Page 8 English Prevent unintentional starting. Ensure Keep cutting tools sharp and clean. the switch is in the off position before Properly maintained cutting tools with sharp connecting to power source and/or cutting edges are less likely to bind and are battery pack, picking up or carrying the easier to control.
-
Page 9: Residual Risks
CAUTION: Burn hazard. To reduce • Do not operate this tool for long periods of the risk of injury, charge only DeWALT time. Vibration caused by hammer action may rechargeable battery packs. Other types be harmful to your hands and arms. Use gloves... -
Page 10: Charging Process
English extension cord could result in risk of fire, 2. Insert the battery pack (g) into the charger. electric shock or electrocution. The red (charging) light will blink continuously indicating that the charging process has started. • When operating a charger outdoors, always provide a dry location and use an extension 3. -
Page 11: Important Safety Instructions For All Battery Packs
English A cold battery pack will charge at about half the rate CAUTION: When not in use, place of a warm battery pack. The battery pack will charge tool on its side on a stable surface at that slower rate throughout the entire charging where it will not cause a tripping or cycle and will not return to maximum charge rate falling hazard. -
Page 12: Storage Recommendations
Do not expose to water. Battery Pack BATTERY TYPE Have defective cords replaced immediately. The DCD731 and DCD734 operate on 14.4 volt battery packs. Charge only between 4 ˚C and 40 ˚C. The DCD771 and DCD776 operate on 18 volt battery packs Only for indoor use. -
Page 13: Description (Fig. 1)
English Mains Plug Replacement • Check for damage to the tool, parts or accessories which may have occurred during (U.K. & Ireland Only) transport. If a new mains plug needs to be fitted: • Take the time to thoroughly read and understand this manual prior to operation. - Page 14 English 2. Insert battery pack into the charger as some models, a hammer symbol. These numbers are used to set the clutch to deliver a torque range. described in the charger section of this manual. The higher the number on the collar, the higher the FUEL GAUGE BATTERY PACKS (FIG.
- Page 15 English 2. Grasp the black sleeve of the chuck with one 4. Make some practice runs in scrap or on unseen hand and use the other hand to secure the areas to determine the proper position of the tool. Rotate the sleeve counterclockwise far clutch collar.
-
Page 16: Optional Accessories
English 8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming. Cleaning 9. With variable speed drills there is no need to center punch the point to be drilled. Use a WARNING: Blow dirt and dust out of slow speed to start the hole and accelerate by the main housing with dry air as often as... -
Page 17: Rechargeable Battery Pack
English environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. WALT provides a facility for the collection and recycling of D WALT products once they have reached the end of their working life. - Page 20 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...