Panasonic CT-27E13G Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. TV
  5. CT27E13G - 27" COLOR TV
  6. Service manual

Panasonic CT-27E13G Service Manual

Hide thumbs Also See for CT-27E13G:
Table of Contents

Advertisement

Quick Links

CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-
This simplified service manual is issued to add listed models to the
main service manual order No. MTNC030623C1(CT-25L8G). A
complete parts list and schematics are included in this simplified
service manual. Please file and use this simplified servicemanual
together with the main service manual order No. MTNC030623C1(CT-
25L8G).
Copyright 2003 Matsushita Electric Corporation of America. All
rights reserved. Unauthorized copying and distribution is a
MC-Service
36E13G / CT-36E33G
1
MTNC030731A1
B05
Color Television
NA10

Advertisement

Table of Contents
loading

Related Manuals for Panasonic CT-27E13G

Summary of Contents for Panasonic CT-27E13G

  • Page 1 MTNC030731A1 Color Television CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT- 36E13G / CT-36E33G NA10 This simplified service manual is issued to add listed models to the main service manual order No. MTNC030623C1(CT-25L8G). A complete parts list and schematics are included in this simplified service manual.

  • Page 2: Safety Precautions

    violation of law. 1. Safety precautions General guidelines An isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injuryfrom electrical shocks.
  • Page 3 Unplug the A.C. cord and connect a jumper between the two plug prongs.Measure the resistance between the jumpered AC plug and expose metallic parts such as screwheads, antenna terminals, control shafts, etc. If the exposed metallic part has a returnpath to the chassis, the reading should be between 240k and 5.2M .

  • Page 4: Service Notes

    Measure the high voltage. The high voltage should be 29.25 ± 1.25kV (for 27” and 32” models) and 31.25 ± 1.25kV (for 36” models). If the upper limit is out of tolerance,immediate service and correction is required to insure safe operation and to prevent the possibility of premature component failure.
  • Page 5 1. Put a small amount of solder on the board soldering pads. 2. Hold the chip component against the soldering pads with tweezers or with a miniature alligator clip and apply heat to the pad area with a 30 watt iron until solder flows. Do not apply heat for more than 3 seconds.
  • Page 6 4. Position the new Flat IC in place (apply the pins of the Flat IC to the soldering pads where the pins need to be soldered). Properly determine the positions of the soldering pads and pins by correctly aligning the polarity symbol 5.
  • Page 7 chassis. Connect the test equipment to the proper ground(hot) or (cold) when servicing, or incorrect voltages will be measured. 2.1. X-Ray Protection Circuit Check& Adjustments This test must be performed as final check before the receiver is returned to the customer. If voltages are out of tolerance, immediate service and correction is required to insure safe operation and to prevent the possibility of premature componentfailure.

  • Page 8: Eeprom Replacement

    5. Apply a monoscope pattern. 6. Set customer picture and brightness controls to the minimum. 7. Set current within 50 A to 100 A by changing the picture and bright controls. 8. Slowly increase AC voltage at the input of the isolation transformer and confirm HHS voltage measure 33kV for 27”...

  • Page 9: About Lead Free Solder (Pbf)

    5. Change to the next ID switch register with “CH” keys and repeat the same procedure as step 4. 6. When replacing a new EEPROM be sure to set the correct ID switch values for each model. 7. Once that all 3 registers are set with the correct address value, perform all of the remaining adjustments and servicing.

  • Page 10: Receiver Feature Table

    the component side for excess solder which may flow onto the opposite side. Suggested Pb free solder There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also beused.
  • Page 11 FEATURE/MODEL CT-27E13G CT-32E13G CT-36E13G CHASSIS DP404 DP407 AP408 MICRO 128K MENU LANGUAGE ENG/SPAN/FR CLOSED CAPTION V-CHIP (USA/CANADA) CHANNEL COUNT REMOTE CONTROL EUR7613Z60 CRT SUPPLIER MDDA CHASSIS NA10 COMB FILTER 3 DIGITAL COLOR TEMP - - - HEC/VEC (X=BOTH) V/A NORM (X=BOTH)

  • Page 12: Board Description Table

    FEATURE/MODEL CT-27E33G CT-32E33G CT-36E33G CHASSIS EP404 EP407 BP408 MICRO 128K MENU LANGUAGE ENG/SPAN/FR CLOSED CAPTION V-CHIP (USA/CANADA) CHANNEL COUNT REMOTE CONTROL EUR7613Z70 CRT SUPPLIER MDDA CHASSIS NA10 COMB FILTER 3 DIGITAL COLOR TEMP - - - HEC/VEC (X=BOTH) V/A NORM (X=BOTH) VIDEO INPUT MEMORY MTS/SAP/DBX BUILT-IN AUDIO POWER...
  • Page 13 MODEL BOARD PART NUMBER DESCRIPTION CT-27E13G TNP2AH047GC MAIN BOARD TNP2AA122GA CRT BOARD CT-27E33G TNP2AH047GD MAIN BOARD TNP2AA122GA CRT BOARD TNP2AA123 PIP PROCESSING BOARD CT-32E13G TNP2AH047KC MAIN BOARD TNP2AA122KA CRT BOARD CT-32E33G TNP2AH047KD MAIN BOARD TNP2AA122KA CRT BOARD TNP2AA123 PIP PROCESSING BOARD...

  • Page 14: Location Of Controls (Remote)

    8. Location of controls (remote) 8.1. EUR7613Z60...
  • Page 15 Note: For additional information about this remote please refer to the owner’s manual section remote operation, listed on the parts list section. 8.2. EUR7613Z70 MC-Service...
  • Page 16 Note: For additional information about this remote please refer to the owner’s manual section remote operation, listed on the parts list section. 9. Dissasembly for service Back cover Remove all the screws marked with an arrow ( ) from the back of the receiver NOTE Screw configuration, type, and number of screws vary depending on the model of the receiver serviced and the application;...
  • Page 17 A-Board - Main chassis 1. Carefully pull out Y1, Y2, Y3 connectors from Y-board and plug from second tuner of A-Board (models with PIP feature only). 2. Slide the chassis completely out of the guide rails. 3. Stand the receiver on its edge. The underside of the board is completely accessible for component replacement.
  • Page 18 NOTE When reassembling speakers be sure to connect the speaker wires to the correct speaker lead (+) 9.1. Disassembly for CRT replacement 1. Discharge the CRT as instructed in the “safety precautions”. 2. Disconnect the yoke (DY) plug, degaussing coil (DEG) plug from the main board.
  • Page 19 To remove and remount the degaussing coil: - Unhook the coil spring from the bottom corners of the CRT ears. - Release the braid loop from the upper corners of the CRT ears. 7. Mount the dag ground braid on the replacement CRT. Position the degaussing coil with new ties.

  • Page 20: Chassis Service Adjustment Procedures

    10. Chassis service adjustment procedures All service adjustments are factory preset and should not require adjustment unless controls and/ or associated components are replaced. Note: Connect the (-) lead of the voltmeter to the appropriate ground. Use IC801’s heat sink when the HOT ground symbol is used. Otherwise, use COLD ground (Tuner shield, IC451’s heat sink or FA2).
  • Page 21 Note: Components and test points within doted areas are located on trace side. B+ voltage check 1. Set the BRIGHT and PICTURE to minimum by using the PICTURE menu. 2. Connect the DVM between C825 (+ side) or TPD14 and cold ground.

  • Page 22: Service Adjustments (Mechanical Controls)

    A-BOARD TEST 27” & 36”VOLTAGE POINT 32”VOLTAGE TPD14 131.0 ± 2.0V 131.0±2.0V SOUND C823 (+) 22.7 ± 1.0V 22.7 ± 1.0V STB12V C827 (+) 12.8 ± 1.0 V 12.8 ± 1.0 V 220V TPA14 217 ± 10 V 213 ± 10 V VERTICAL TPD8 27.4 ±...
  • Page 23 12. Service mode (electronic adjustments) This receiver has electronic technology using the I C bus concept. It performs as a control function and it replaces many mechanical controls. Instead of adjusting mechanical controls individually, many of the control functions are nowperformed by using “on screen display menu”.
  • Page 24 adjustment modes menu, select adjustment by pressing the volume right/left buttons and channel up/down buttons on the remote and ACTION to enter the adjustment. Exiting the service mode: This TV goes out from service mode when it is unplugged or turned OFF. To exit the service mode, turn the TV OFF from or unplug the TV from A.C.
  • Page 25 (TP1 pin 2) to cold ground (TP1 pin 3). The receiver enters the aging mode. Yellow letters “CHK” appear in the upper left corner of the screen. / (The volume right/left and channel up/down will adjust rapidly). Note: If service mode is accessed by this method be sure to reset the set after service is performed.

  • Page 26: Service Adjustments (Electronic Controls)

    NAME DESCRIPTION CT-27E13G CT-27E33G CT-32E13G CT-32E33G CT-36E13G CT-36E33G ID1* ID SWITCH 1 ID2* ID SWITCH 2 ID3* ID SWITCH 3 IMPORTANT: These table values are approximated and could change due to variation of electrical characteristics in each set, except for the ID switch values.
  • Page 27 “BRIGH”, and adjust data to obtain 3.6±0.1V between 7.5 IRE and GND level at TP35 (TP47G). (See waveform detail). 2. In service mode, select DAC for contrast adjustment “CONT”, and adjust data to obtain between 7.5IRE and 100IRE level at TP35 (TP47G).
  • Page 28 Make sure that sub-contrast adjustment was finished prior to perform this adjustment. PREPARATION 1. Normalize the picture settings. 2. Set the BRIGHTNESS control to minimum. 3. Set the COLOR control to the center. 4. Set the TINT control to the center. 5.
  • Page 29 13.4. Color output adjustment / Service DAC adjustment / (COLOR, TINT, B-Y_G) NOTE Color and tint adjustment sets the reference settings for the user controls; It is important to read the procedures. (NO RAINBOW PATTERN) Make sure that sub-contrast adjustment was finished prior to perform this adjustment PREPARATION Normalize the picture settings.
  • Page 30 required for “good gray scale and warm highlights”. 1. LOW LIGHT areas - In service mode for making electronic adjustments, select CUT R, CUT G, CUT B and adjust the picture for gray. 2. HIGH LIGHT areas - In service mode for making electronic adjustments, select drive R DR, B DR and adjust the picture for warm whites.
  • Page 31 6. Turn screen clockwise slowly until color is slightly appeared. 7. Then adjust “CUT R” and “CUT B” until line becomes white. 8. Press RECALL button on the remote to restore the raster. 9. Adjust “R DR” and “B DR” so the white seems like white and black like black.
  • Page 32 2. If the horizontal center is not aligned, in service mode adjust “H POS” DATA to adjust the horizontal center of the monoscope pattern to the CRT center. 3. Verify that horizontal width (A & B mark) is within 4.5 ± 0.7. 13.6.2.
  • Page 33 monoscope pattern to the center vertical position of the CRT center mark. 2. Adjust linearity data “V-C” so that interval of “a” is same as “b” (a= 3. If the v-position is not at the CRT center, adjust / V position “V POS”...
  • Page 34 2. Check a and b sizes, If b-a < -1.5mm (in top & bottom extending case) - Increase “V-S” DATA by one step NOTE Repeat “a” and “b” until b-a ± 1.5mm 3. Confirm to make outermost circle of monoscope pattern a correct circle V-Adjustment 13.6.5.
  • Page 35 1. Apply a crosshatch pattern. 2. Normalize the picture icon video adjustments. Procedure: 1. Adjust “PCC” data so that the first and third line make a good balance (see figure below). PCC Adjustment 13.6.7. Corner PCC adjustment / (TOPG, TOPSL, BTMG, BTMSL) This controls help to adjust top and bottom sides of picture.
  • Page 36 1. Input level adjustment. 2. Stereo separation adjustment. Input level adjustment / Service DAC adjustment (MTSIN) PREPARATION 1. Connect an RMS meter with filter jig as shown in figure to TPE11. Filter Jig 2. Connect an RF signal generator to the RF antenna input. PROCEDURE 1.

  • Page 37: Identification Of Components

    - Video: 100 IRE flat field, 30% modulation. - Audio: 300Hz, 30% modulation, stereo (left only) (70±5dB, 75 OPEN, P/S 10dB). NOTE After setting 30% modulation with P.L. SW and N.R. SW OFF, turn P.L. SW and N.R. SW 3. In service mode, adjust the MTS Low-Level separation adjustment “SEPAL”...
  • Page 38 14.1.1. C-Board Chassis C-Board component location 14.1.2. C-Board Chassis (36” Models)
  • Page 39 14.1.3. Y-Board Chassis MC-Service...
  • Page 41 14.1.4. A-Board Chassis 14.1.5. A-Board Surface-mounted components A-Board (bottom view) MC-Service...
  • Page 43 14.1.6. Y-Board Surface-mounted components Y-Board (bottom view) MC-Service...
  • Page 44 15. Reference for PDF Colors...

  • Page 45: Conductor Views

    16. Conductor Views 16.1. A-Board Printed Circuit TNP2AH047 (Left Side) 16.2. A-Board TNP2AH047& C Board TNP2AA122 Printed Circuit (Right Side) 16.3. C-Board Printed Circuit TNP2AA157 16.4. Y-Board Printed Circuit TNP2AA123 17. Block Diagrams 17.1. Video Signal Block Diagram (page 1 of 2) 17.2.
  • Page 47 18.2. Notas de Esquemáticos en Español MC-Service...

  • Page 49: Parts Location

    18.3. A-Board Schematic TNP2AH047GC/KC/LA (page 1 of 4) 18.4. A-Board Schematic TNP2AH047GC/KC/LA (page 2 of 4) 18.5. A-Board Schematic TNP2AH047GC/KC/LA (page 3 of 4) 18.6. A-Board Schematic TNP2AH047GC/KC/LA (page 4 of 4) 18.7. A-Board Schematic TNP2AH047GD/KD/LB (page 1 of 4) 18.8.

  • Page 50: Parts List

    20. Parts List 20.1. Parts List Notes 20.2. Parts List...
  • Page 51 TCJ2VB1H221K CAP C 220PF-K-50V C073 TCJ2VC1H101J CAP C 100PF-J-50V C077 ECA1HM100B CAP E 10UF/50V C079 TCJ2VC1H220J CAP C 22PF-J-50V C083 TCJ2VF1H103Z CAP C .01UF-Z-50V C085 ECJ2VB1C104K CAP C .1UF-K-16V C350 ECA1CM101B CAP E 100UF/16V / CT-27E13G CT-27E33G CT-32E13G CT-32E33G MC-Service...
  • Page 52 C350 ECA1CM101B CAP E 100UF/16V / CT-27E13G CT-27E33G CT-32E13G CT-32E33G...
  • Page 53 Part Name & Description Remarks C351 TACCV470T50V CAP C 47PF/50V / CT-36E33G CT-36E13G C351 TCJ2VC1H331J CAP C 330PF-J-50V / CT-27E13G CT-27E33G CT-32E13G CT- 32E33G C352 TACCV330T50V CAP C 33PF/50V / CT-36E33G CT-36E13G C352 TCJ2VC1H331J CAP C 330PF-J-50V / CT-27E13G CT-27E33G CT-32E13G CT-32E33G...
  • Page 54 CAP E 470UF/160V / CT-32E13G CT-32E33G CT-36E33G CT-36E13G C806 ECQM4103KZW CAP P .01UF-K-400V C808 ECA1HM470B CAP E 47UF-50V C809 ECKR1H102KB5 CAP C .001UF-K-50V / CT-27E13G CT-27E33G CT-36E33G CT- 36E13G C809 ECKR2H152KB5 CAP C .0015UF-K-500V / CT-32E13G CT-32E33G C810 ECKR1H471KB5 CAP C 470PF-K-50V C812 ECQU2A224MVA CAP P .22UF-M-250VAC...
  • Page 55 Ref. No. Part No. Part Name & Description Remarks C830 ECA1CM471B CAP E 470UF-16V C901 TCJ2VB1H103K CAP C .01UF-K-50V / CT-36E33G CT-36E13G C904 ECKR1H103ZF5 CAP C .01UF-Z-50V / CT-36E33G CT-36E13G C952 ECA1HM100B CAP E 10UF/50V / CT-36E33G CT-36E13G C953 ECKR1H103ZF5 CAP C .01UF-Z-50V / CT-36E33G CT-36E13G C958 ECA2CM470E...
  • Page 56 Ref. No. Part No. Part Name & Description Remarks C1832 ECA1HMR22B CAP E .22UF-50V / CT-27E33G CT-32E33G CT-36E33G C1834 TCJ2VC1H150J CAP C 15PF-J-50V / CT-27E33G CT-32E33G CT-36E33G C1835 TCJ2VF1H103Z CAP C .01UF-Z-50V / CT-27E33G CT-32E33G CT-36E33G C1836 ECA1EM470B CAP E 47UF-25V / CT-27E33G CT-32E33G CT-36E33G C1838 TCJ2VF1H103Z CAP C .01UF-Z-50V / CT-27E33G CT-32E33G CT-36E33G...
  • Page 57 Ref. No. Part No. Part Name & Description Remarks C2511 ECA1HM010B CAP E 1UF-50V C2512 ECJ2VB1C104K CAP C .1UF-K-16V C2513 ECA1HM4R7B CAP E 4.7UF-50V C2514 ECA1HM4R7B CAP E 4.7UF-50V C2515 ECJ2VF1C105Z CAP C 1.0UF-Z-16V C2516 ECA1HM4R7B CAP E 4.7UF-50V C2517 ECA1HM4R7B CAP E 4.7UF-50V C2518...
  • Page 58 DIODE D3023 MAZ31100ML DIODE ZENER D3024 MAZ31100ML DIODE ZENER FUSES F801 XBA2A00101 FUSE 6.3A 125V INTEGRATED CIRCUITS IC001 MN101E03GTB3 IC002 TVR2AJ166S EEPROM / CT-27E13G CT-27E33G CT-36E13G CT-36E33G IC002 TVR2AJ167S EEPROM / CT-32E13G CT-32E33G IC003 GP1UE282GK IR SENSOR IC004 PST9128NR RESET...
  • Page 59 EXCELSA35T FERRITE BEAD L245 EXCELSA35V FERRITE BEAD L312 EXCELSA24T FERRITE BEAD L351 G0C101KA0021 COIL PEAKING 100UH / CT-27E13G CT-27E33G CT-32E13G CT- 32E33G L551 ELH5L7101 HORIZONTAL LINEARITY COIL / CT-36E33G CT-36E13G L551 ELH5L7103 HORIZONTAL LINEARITY COIL / CT-27E13G CT-27E33G L551 ELH5L7115...
  • Page 60 TRANSISTORS Q001 2SD601ARTX TRANSISTOR Q070 2SD601ARTX TRANSISTOR Q092 2SB709ARTX TRANSISTOR Q351 2SC3063RL TRANSISTOR / CT-27E13G CT-27E33G CT-32E13G CT-32E33G Q352 2SC3063RL TRANSISTOR / CT-27E13G CT-27E33G CT-32E13G CT-32E33G Q353 2SC3063RL TRANSISTOR / CT-27E13G CT-27E33G CT-32E13G CT-32E33G Q354 2SD601ARTX TRANSISTOR Q355 2SD601ARTX TRANSISTOR...
  • Page 61 Q953 2SC1741ASTP TRANSISTOR / CT-36E33G CT-36E13G MC-Service...
  • Page 62 Ref. No. Part No. Part Name & Description Remarks Q954 2SB1030ATA TRANSISTOR / CT-36E33G CT-36E13G Q955 2SB1569AF51E TRANSISTOR / CT-36E33G CT-36E13G Q956 2SD2400AF51E TRANSISTOR / CT-36E33G CT-36E13G Q957 2SA1309ATA TRANSISTOR / CT-36E33G CT-36E13G Q958 2SC3311ATA TRANSISTOR / CT-36E33G CT-36E13G Q961 2SC3311ATA TRANSISTOR / CT-36E33G CT-36E13G Q962...
  • Page 63 R039 ERDS2TJ102T RES C 1K-J-1/4W MC-Service...
  • Page 64 R093 ERJ6GEYJ331V RES M 330-J-1/10W R202 ERJ6GEYJ222V RES M 2.2K-J-1/10W R351 ERG2FJ123H RES M 12K-J-2W / CT-27E13G CT-27E33G CT-32E13G CT-32E33G R351 ER0S2THF1001 RES M 1K-F-1/4W / CT-36E33G CT-36E13G R352 ERG2FJ123H RES M 12K-J-2W / CT-27E13G CT-27E33G CT-32E13G CT-32E33G R352 ER0S2THF1001...
  • Page 65 RES M 2K-F-1/4W / CT-36E33G CT-36E13G R363 ERC12GK102D RES C 1K-K-1/2W / CT-36E33G CT-36E13G R363 ERJ6GEYJ101V RES M 100-J-1/10W / CT-27E13G CT-27E33G CT-32E13G CT-32E33G R364 ERC12GK102D RES C 1K-K-1/2W / CT-36E33G CT-36E13G R364 ERJ6GEYJ101V RES M 100-J-1/10W / CT-27E13G CT-27E33G CT-32E13G CT-32E33G...
  • Page 66 RES F .56-J-2W / CT-32E13G CT-32E33G R559 ERG2FJ683H RES M 12K-J-2W R561 ERG2FJ102H RES M 1K-J-2W R562 ERG2FJ270H RES M 27-J-2W / CT-27E13G CT-32E13G CT-36E13G R562 ERX3FJ4R7H RES M 4.7-J-3W / CT-27E33G CT-32E33G CT-36E33G R563 ERG3FJ150H RES M 15-J-3W R564 ERDS2TJ104T...
  • Page 67 Ref. No. Part No. Part Name & Description Remarks R810 ERDS2TJ221T RES C 220-J-1/4W R815 ERC12ZGK825D RES C 8.2MEG-K-1/2W R821 ERDS1FJ1R0T RES C 1.0-J-1/2W R822 ERDS1FJ1R0T RES C 1.0-J-1/2W R823 ERDS1FJ272T RES C 2.7K-J-1/2W R824 ERDS2TJ223T RES C 22K-J-1/4W R825 ERDS2TJ272T RES C 2.7K-J-1/4W R827...
  • Page 68 Ref. No. Part No. Part Name & Description Remarks R993 ERDS2TJ471T RES C 470-J-1/4W / CT-36E33G CT-36E13G R1804 ERJ6GEYJ103V RES M 10K-J-1/10W / CT-27E33G CT-32E33G CT-36E33G R1805 ERJ6GEYJ102V RES M 1K-J-1/10W / CT-27E33G CT-32E33G CT-36E33G R1806 ERJ6GEYJ392V RES M 3.9K-J-1/10W / CT-27E33G CT-32E33G CT-36E33G R1807 ERJ6GEYJ102V RES M 1K-J-1/10W / CT-27E33G CT-32E33G CT-36E33G...
  • Page 69 Ref. No. Part No. Part Name & Description Remarks R2505 ERDS2TJ101T RES C 100-J-1/2W R3001 ERDS2TJ101T RES C 100-J-1/4W R3002 ERJ6GEYJ221V RES M 220-J-1/10W R3003 ERJ6GEYJ221V RES M 220-J-1/10W R3004 ERDS2TJ101T RES C 100-J-1/4W R3005 ERJ6GEYJ334V RES M 330K-J-1/10W R3006 ERJ6ENF75R0V RES M 75.0-F-1/10W R3007...
  • Page 70 DEFLECTION YOKE / CT-27E13G CT-27E33G TLY2AA008 DEFLECTION YOKE / CT-32E13G CT-32E33G KDY42L632F DEFLECTION YOKE / CT-36E13G CT-36E33G JH291U-009 CONVERGENCE & PURITY RINGS / CT-27E13G CT-27E33G CT- 32E13G CT-32E33G TP-11900PLX CONVERGENCE & PURITY RINGS / CT-36E13G CT-36E33G TLK2AA0011 27 INCH DEGAUSSING COIL / CT-27E13G CT-27E33G...
  • Page 71 TJB2AA0211-1 2 JACK A/V TERMINAL OTHERS ACCESSORIES M006 TQB2AA0458 OWNERS MANUAL / CT-27E33G CT-32E33G CT-36E33G M007 TQB2AA0459 OWNERS MANUAL / CT-27E13G CT-32E13G CT-36E13G M008 EUR7613Z60 REMOTE CONTROL / CT-27E13G CT-32E13G CT-36E13G M009 EUR7613Z70 REMOTE CONTROL / CT-27E33G CT-32E33G CT-36E33G M010...
  • Page 72 A-BOARD 1 of 4 TNP2AH047GC/KC/LA CT-27E13G / CT-32E13G / CT-36E13G...
  • Page 73 MC-Service A-BOARD 1 of 4 TNP2AH047GD/KD/LB CT-27E33G / CT-32E33G / CT-36E33G...
  • Page 74 MC-Service A-BOARD 2 of 4 TNP2AH047GC/KC/LA CT-27E13G / CT-32E13G / CT-36E13G...
  • Page 75 MC-Service A-BOARD 2 of 4 TNP2AH047GD/KD/LB CT-27E33G / CT-32E33G / CT-36E33G...
  • Page 76 MC-Service A-BOARD 3 of 4 TNP2AH047GC/KC/LA CT-27E13G / CT-32E13G / CT-36E13G...
  • Page 77 MC-Service A-BOARD 3 of 4 TNP2AH047GD/KD/LB CT-27E33G / CT-32E33G / CT-36E33G...
  • Page 78 MC-Service A-BOARD 4 of 4 TNP2AH047GC/KC/LA CT-27E13G / CT-27E13UG / CT-32E13G / CT-32E13UG / CT-36E13G / CT-36E13UG...
  • Page 79 MC-Service A-BOARD 4 of 4 TNP2AH047GD/KD/LB CT-27E33G / CT-32E33G / CT-36E33G...

  • Page 80: Audio Signal Path Block Diagram

    R-OUT L-OUT REAR AUDIO R-IN L-IN IC2501 R-OUT L-OUT JK3002 R-IN L-IN FRONT VAO-R AUDIO IC2301 AUDIO AMP VAO-L R-OUT L-OUT MUTE JK3004 TO AUDIO SP ON/OFF IC001 CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G MC-Service...
  • Page 81 MC-Service C-BOARD TNP2AA122GA/KA CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G...
  • Page 82 MC-Service C-BOARD 1 of 2 TNP2AA157AM CT-36E13G / CT-36E33G...
  • Page 83 MC-Service 2 of 2 C-BOARD TNP2AA157AM CT-36E13G / CT-36E33G...
  • Page 84 CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G A-BOARD 1 of 2 TNP2AH047...
  • Page 85 A-BOARD 2 of 2 TNP2AH047 C-BOARD TNP2AA122 CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G...
  • Page 86 MC-Service C-BOARD TNP2AA157 CT-36E13G / CT-36E33G...
  • Page 87 MC-Service Y-BOARD TNP2AA123 CT-27E33G / CT-32E33G / CT-36E33G...

  • Page 88: Video Signal Path Block Diagram

    MSCIN Q360 Q361 Q362 Q357 Q358 Q359 Q354 Q355 Q356 JK3003 S-VIDEO R-IN G-IN B-IN Q351 Q352 Q353 IC351 R-OUT G-OUT B-OUT C-BOARD C-BOARD FOR 36" MODELS MC-Service ONLY CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G...
  • Page 89 Video signal path block diagram Y-BOARD IC1801 C IN Y (R) OUT Y IN V2/Y2 V2/Y2 V (B) OUT V IN U IN U (G) OUT V1/Y1 V1/Y1 V1/Y1 IC1804 VIDEO SWITCH TV IN 1 JK3001 7 V/Y OUT REAR VIDEO IN 1 IN 2 IC1803...
  • Page 90 ..0.00 ..0.40 ..0.00 ..0.40 ..3.30 MC-Service CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G...
  • Page 91 . . . 216.80 2.80 5.80 5.70 0.30 2.40 . . . 145.30 105.30 0.00 8.90 1.80 8.90 . . . 152.70 2.70 6.30 5.10 0.00 1.90 . . . 151.00 CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G MC-Service...
  • Page 92 0.80 4.40 4.00 0.30 0.00 4.00 8.90 2.20 1.40 3.80 3.30 0.00 Q1806 Q1808 Q1809 Q1810 3.00 0.70 0.90 1.60 1.10 0.00 0.00 8.90 3.30 1.40 1.60 0.00 MC-Service CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G...
  • Page 93 IC501 PIN 4 (H-DRIVE) A12 PIN 2 (HEATER) 284 Vp-p 90 Vp-p 1.42 kVp-p 2.10 Vp-p Q551 Collector (H OUT) IC801 PIN 1 IC801 PIN 7 Q501 Collector MC-Service CT-27E13G / CT-27E33G / CT-32E13G / CT-32E33G / CT-36E13G / CT-36E33G...
  • Page 94 MC-Service Y-BOARD 1 of 2 TNP2AA123 CT-27E33G / CT-32E33G / CT-36E33G...
  • Page 95 MC-Service Y-BOARD 2 of 2 TNP2AA123 CT-27E33G / CT-32E33G / CT-36E33G...

This manual is also suitable for:

Ct-27e33gCt-32e13gCt-32e33gCt-36e13gCt-36e33g

Table of Contents