Page 1: Table Of Contents
2007 Saab 9-7X Owner Manual Seats and Restraint Systems ... 7 Front Seats ... 9 Rear Seats ... 16 Safety Belts ... 18 Child Restraints ... 38 Airbag System ... 64 Restraint System Check Features and Controls ... 85 Keys ...
Page 2 Service and Appearance Care ... 319 Service ... 322 Fuel ... 324 Checking Things Under the Hood All-Wheel Drive ... 368 Rear Axle ... 369 Front Axle ... 370 Headlamp Aiming ... 371 Bulb Replacement ... 371 Windshield Replacement Windshield Wiper Blade Replacement ...
Page 3: Canadian Owners
Saab Automobile, Saab Cars USA, SAAB, Saab 9-7X, 9-7X and the Saab Emblem are registered trademarks of Saab Automobile, AB. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Page 4: How To Use This Manual
How to Use This Manual Many people read the owner manual from beginning to end when they ﬁrst receive their new vehicle. If this is done, it can help you learn about the features and controls for the vehicle. Pictures and words work together in the owner manual to explain things.
Page 5 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 6 These are some examples of symbols that may be found on the vehicle:...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ... 9 Power Seats ... 9 Power Lumbar ... 9 Heated Seats ... 10 Memory Seat, Mirrors, and Pedals ... 11 Power Reclining Seatbacks ... 13 Head Restraints ... 15 Rear Seats ... 16 Rear Seat Operation ... 16 Safety Belts ...
Page 8 Section 1 Airbag System ... 64 Where Are the Airbags? ... 67 When Should an Airbag Inﬂate? ... 70 What Makes an Airbag Inﬂate? ... 72 How Does an Airbag Restrain? ... 72 What Will You See After an Airbag Inﬂates? ... 73 Passenger Sensing System ...
Page 9: Front Seats
Front Seats Power Seats The power seat controls are located on the outboard side of the seat cushions. • Move the seat forward or rearward by sliding the horizontal control forward or rearward. • Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down.
Page 10 Heated Seats Your vehicle has heated front seats. The buttons used to control this feature are located on the front door armrests. The engine must be running for the heated seat feature to work. To heat the entire seat, press the horizontal button with the heated seat and seatback symbol.
Page 11 Memory Seat, Mirrors, and Pedals The controls for the memory function are located on the driver’s door. These buttons are used to program and recall memory settings for the driver’s seating position, both outside mirror positions, and the adjustable pedals, if equipped. The settings for these features can be saved for up to two drivers.
Page 12 To recall the memory settings, do one of the following: • Press and release button 1 or 2 while the vehicle is in PARK (P). A single chime will sound and the memory position will be recalled. • If programmed to do so through the Driver Information Center (DIC), pressing the unlock button on the Remote Keyless Entry (RKE) transmitter will recall the preset...
Page 13: Power Reclining Seatbacks
To recall the easy exit seat position, do one of the following: • Press the easy exit seat button on the memory control while the vehicle is in PARK (P). The seat will move to the stored exit position. • Or, if the easy exit seat feature is activated in the Driver Information Center (DIC), removing the key from the ignition will move the seat...
Page 14 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 15: Head Restraints
Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it.
Page 16: Rear Seats
Rear Seats Rear Seat Operation Your vehicle has ﬂip and fold second row seats which provide additional cargo space. To ﬂip and fold the seat(s), do the following: 1. Pull up on the loop located where the seat cushion meets the seatback and ﬂip the seat cushion forward.
Page 17 To return the seat(s) to the original position, do the following: CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked.
Page 18: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 19 A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without belts they could have been badly hurt or killed.
Page 20 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 21 The person keeps going until stopped by or the instrument panel... something. In a real vehicle, it could be the windshield...
Page 22: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after an...
Page 23: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Page 24: Driver Position
Driver Position Lap-Shoulder Belt The driver has a lap-shoulder belt. Here is how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats” in the Index. 3.
Page 25 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Page 26 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 27 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force at your abdomen.
Page 28 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen.
Page 29 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 30 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 31: Safety Belt Use During Pregnancy
To unlatch the belt, push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 32: Rear Seat Passengers
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it is more likely that the fetus will not be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 33 Lap-Shoulder Belt All rear seat positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
Page 34 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt.
Page 35: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
Page 36 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash.
Page 37: Safety Belt Extender
To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide. Slide the guide back onto its storage clip located between the interior body and the seatback. Safety Belt Pretensioners Your vehicle has safety belt pretensioners for the driver and right front passenger.
Page 38: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 39 CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time.
Page 40: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide CAUTION: (Continued) CAUTION: (Continued) under the belt.
Page 41 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts. Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints.
Page 42 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 43 When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufacturer’s instructions that come with the restraint state the weight and height limitations for a particular child restraint.
Page 44: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 45 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system.
Page 46 How Should I Use a Child Restraint? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 47 When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 48: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 49 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off. Here is why: CAUTION: A child in a rear-facing child restraint can...
Page 50 Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system Make sure that a LATCH-compatible child restraint...
Page 51 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 52 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Second Row (Top Tether Anchor): The labels are located above a ﬂap, at the base of the seatback, in the rear outside seating positions. The anchors are located under the ﬂap.
Page 53 The top tether anchors for each rear seating position are located on the ﬂoor in the cargo area of your vehicle. Do not use the rear tie-down brackets near the liftgate for top tethers. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 54 Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed.
Page 55 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has...
Page 56 1.4. Attach and tighten the lower attachments on the child restraint to the lower anchors. 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if your vehicle has one. Refer to the child restraint instructions and the following steps: 2.1.
Page 57 Securing a Child Restraint in a Rear Outside Seat Position If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 50. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position.
Page 58 4. Pull the rest of the shoulder belt all the way 5. To tighten the belt, push down on the child out of the retractor to set the lock. restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor.
Page 59 6. If your child restraint manufacturer recommends using a top tether, attach and tighten the top tether to the top tether anchor. Refer to the instructions that came with the child restraint and to Lower Anchors and Tethers for Children (LATCH) on page 50. 7.
Page 60 Securing a Child Restraint in the Right Front Seat Position Your vehicle has a right front passenger’s airbag. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 48. In addition, your vehicle has a passenger sensing system.
Page 61 CAUTION: (Continued) If you need to secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. If you need to secure a forward-facing child restraint in the right front seat position, move the seat as far back as it will go before securing the forward-facing...
Page 62 4. Buckle the belt. Make sure the release button 5. Pull the rest of the shoulder belt all the way is positioned so you would be able to unbuckle out of the retractor to set the lock. the safety belt quickly if you ever had to.
Page 63 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 64: Airbag System
Airbag System Your vehicle has a frontal airbag for the driver and another frontal airbag for the right front passenger. Your vehicle also has roof-mounted side impact airbags designed for either side impact or rollover deployment. Roof-mounted side impact airbags are available for the driver and the passenger seated directly behind the driver and for the right front passenger and the passenger seated directly...
Page 65 Here are the most important things to know about the airbag system: CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 66 CAUTION: Both frontal and roof-mounted side impact airbags inﬂate with great force, faster than the blink of an eye. If you are too close to an inﬂating airbag, as you would be if you were leaning forward, it could seriously injure you.
Page 67: Where Are The Airbags
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 178 for more information. Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel.
Page 68 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. The roof-mounted side impact airbag for the driver and the person seated directly behind the driver is in the ceiling above the side windows.
Page 69 The roof-mounted side impact airbag for the right front passenger and the person seated directly behind that passenger is in the ceiling above the side windows. CAUTION: If something is between an occupant and an airbag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 70: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in...
Page 71 Frontal airbags (driver and right front passenger) are not intended to inﬂate during vehicle rollovers, rear impacts, or in many side impacts. Your vehicle has seat position sensors which enables the sensing system to monitor the position of the driver’s seat and the right front passenger’s seat.
Page 72: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In an impact of sufficient severity, the airbag sensing system detects that the vehicle is in a crash. Additionally, in the case of a “rollover capable” roof-mounted side impact airbag, the sensing system detects that the vehicle is about to roll over.
Page 73: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After a frontal airbag inﬂates, it quickly deﬂates, so quickly that some people may not even realize an airbag inﬂated. Roof-mounted rollover airbags may still be at least partially inﬂated minutes after the vehicle comes to rest.
Page 74: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for your airbag system.
Page 75 The words ON and OFF, or the symbol for on and off, will be visible during the system check. When the system check is complete, either the word ON or the word OFF, or the symbol for on or the symbol for off, will be visible.
Page 76 If your vehicle has a rear seat that will accommodate a rear-facing child restraint, a label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys.
Page 77 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off. Here is why: CAUTION: A child in a rear-facing child restraint can...
Page 78 • The system determines that a small child is present in a booster seat. • A right front passenger takes his/her weight off of the seat for a period of time. • The right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints.
Page 79 If this happens, turn the vehicle off and ask the person to place the seatback in the fully upright position, then sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. Restart the vehicle and have the person remain in this position for about two minutes.
Page 80: Servicing Your Airbag-Equipped Vehicle
Aftermarket equipment, such as seat covers, can affect how well the passenger sensing system operates. You may want to consider not using seat covers or other aftermarket equipment if your vehicle has the passenger sensing system. See Adding Equipment to Your Airbag-Equipped Vehicle on page 81 for more information about modiﬁcations that can affect how the system operates.
Page 81: Adding Equipment To Your
CAUTION: For up to 10 seconds, after the ignition is turned off and the battery is disconnected, an airbag can still inﬂate during improper service. You can be injured if you are close to an airbag when it inﬂates. Avoid yellow connectors.
Page 82: Restraint System Check
Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my airbag system? Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module, steering wheel, instrument panel, the inside review mirror, ceiling headliner, ceiling and pillar garnish trim, roof-mounted airbag modules, or airbag...
Page 83: Replacing Restraint System Parts
Notice: If you damage the covering for the driver’s or the right front passenger’s airbag, or the side impact airbag covering on the ceiling near the side windows, the airbag may not work properly. You may have to replace the airbag module in the steering wheel, both the airbag module and the instrument panel for the right front passenger’s airbag, or side impact airbag...
Page 84 If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced.
Page 85: Features And Controls
Section 2 Keys ... 87 Remote Keyless Entry (RKE) System ... 89 Remote Keyless Entry (RKE) System Operation ... 90 Doors and Locks ... 92 Door Locks ... 92 Power Door Locks ... 93 Delayed Locking ... 94 Programmable Automatic Door Locks ... 94 Rear Door Security Locks ...
Page 86 Section 2 Outside Curb View Assist Mirror ... 124 Outside Convex Mirror ... 124 Outside Heated Mirrors ... 124 ® OnStar System ... 125 Universal Home Remote System ... 128 Universal Home Remote System (With Three Round LED) ... 128 Universal Home Remote System (With One Triangular LED) ...
Page 87: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
Page 88 This vehicle has double-sided keys that can be used for the ignition and door lock. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a key code number. The key code number tells your dealer or a qualiﬁed locksmith how to make extra keys.
Page 89: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System Your Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 90: System Operation
Remote Keyless Entry (RKE) System Operation With this system you can lock and unlock your doors from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. The remote keyless entry transmitter buttons will not operate when the key is in the ignition.
Page 91 Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about two years. The battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Page 92: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 93: Power Door Locks
There are several ways to lock and unlock your vehicle. From the outside, use the remote keyless entry transmitter or the key. From the inside, slide the manual lever forward or rearward. The manual lever on each door works only that door’s lock.
Page 94: Delayed Locking
Delayed Locking This feature delays the locking of the doors and the liftgate when using the power lock or the remote keyless entry system. The ﬁrst press of the power door lock switch or lock button on the remote keyless entry transmitter with the driver’s door open will activate the delay locking.
Page 95 Programmable Locking Feature Following are the two locking modes that can be programmed: Mode 1: All doors lock when the transmission is shifted out of PARK (P). Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h). The automatic door locks were pre-programmed at the factory to lock all the doors when the transmission is shifted into gear.
Page 96 Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into PARK (P). Mode 2: All doors unlock when the transmission is shifted into PARK (P). Mode 3: All doors unlock when the key is removed from the ignition.
Page 97: Rear Door Security Locks
Rear Door Security Locks Your vehicle may have this feature. You can lock the rear doors so they cannot be opened from the inside by passengers. To use one of these locks do the following: 1. Open one of the rear doors. You will ﬁnd a security lock lever located on the inside edge of each rear door.
Page 98: Liftgate/Liftglass
Liftgate/Liftglass CAUTION: It can be dangerous to drive with the liftgate or liftglass open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate or...
Page 99: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 100: Power Windows
Power Windows The controls for the power windows are located on the armrest on each of the side doors. With power windows, the switches operate the windows when the ignition is in RUN, ACC or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 108.
Page 101: Theft-Deterrent Systems
Window Lockout (Lockout): Your vehicle has a lockout feature to prevent passengers from operating the power windows. The lockout switch is located in front of the window switches on the driver’s door. A light in the lockout switch will come on to show that the switch has been activated.
Page 102: Content Theft-Deterrent
Content Theft-Deterrent Your vehicle is equipped with a content theft-deterrent alarm system. Here is how to operate the system: 1. Open the door. 2. Lock the door with the power door lock switch or the remote keyless entry transmitter. The security light should ﬂash.
Page 103 Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter.
Page 104: Pass-Key
® PASS-Key III Operation Your vehicle is equipped with the PASS-Key (Personalized Automotive Security System) theft-deterrent system. PASS-Key is a passive theft-deterrent system. This means you do not have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition.
Page 105 It is possible for the PASS-Key learn the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. This procedure is for programming additional keys only. Canadian Owners: If you lose or damage your keys, only a GM dealer can service PASS-Key to have new keys made.
Page 106: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km).
Page 107: Ignition Positions
Ignition Positions Use the key to turn the ignition switch to four different positions. The ignition switch is located on the center console. (LOCK): This position locks the ignition and transmission. It is a theft-deterrent feature. You will only be able to remove the key when the ignition is turned to LOCK and the vehicle has power.
Page 108: Retained Accessory Power (Rap)
Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime will sound, when you open the driver’s door.
Page 109 Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts.
Page 110: Adjustable Throttle And Brake Pedal
Adjustable Throttle and Brake Pedal If your vehicle has this feature, you can change the position of the throttle and brake pedals. This feature is designed for shorter drivers, since the pedals cannot move farther away from the standard position, but can move closer for better pedal reach. If your vehicle has this feature, it can be programmed to work with the memory function.
Page 111 To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment next to the battery box facing the engine. 3.
Page 112: Automatic Transmission Operation
Automatic Transmission Operation There are several different positions for your gear shift lever. PARK (P): This position locks the rear wheels. It is the best position to use when you start the engine because your vehicle cannot move easily. CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 113 Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You have to fully apply the regular brakes ﬁrst and then press the shift lever button before you can shift from PARK (P) when the ignition key is in RUN.
Page 114 DRIVE (D): This position is for normal driving. It provides the best fuel economy for your vehicle. If you need more power for passing, and you are: • Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. •...
Page 115 To shift to the SECOND (2) position, you must ﬁrst press the large button on the shift handle. While the button is pressed, move the shifter in the SECOND (2) position. You can also use SECOND (2) for starting the vehicle from a stop on slippery road surfaces.
Page 116: Parking Brake
Parking Brake To set the parking brake, hold the regular brake pedal down with your foot and pull up on the parking brake lever located between the seats. If the ignition is on, the brake system warning light on the instrument panel cluster will come on. See Brake System Warning Light on page 183.
Page 117: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 118: Shifting Out Of Park (P)
Torque Lock If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 119: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different. •...
Page 120: Running The Engine While Parked
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 121: Mirrors
Mirrors Automatic Dimming Rearview Mirror ® with OnStar and Compass Your vehicle may have an automatic-dimming rearview mirror with a compass and the OnStar system. There are three additional buttons for the OnStar system. See your dealer for more information on the system and how to subscribe to OnStar ®...
Page 122 Compass Calibration Press and hold the on/off button to activate the compass calibration mode. CAL will be displayed in the compass window on the mirror. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction.
Page 123: Automatic Dimming Rearview Mirror With Compass
Automatic Dimming Rearview Mirror with Compass Your vehicle may have an automatic dimming rearview mirror with a compass. (On/Off): This is the on/off button for the automatic dimming feature and compass. See Automatic Dimming Rearview Mirror with ® OnStar and Compass on page 121 for information on mirror operation.
Page 124: Outside Curb View Assist Mirror
Outside Curb View Assist Mirror The passenger’s outside mirror will adjust to a preset tilt position while the vehicle is in REVERSE (R) gear. Curb view assist may be useful when you are parallel parking. The mirror will return to normal position when the vehicle is shifted out of REVERSE (R) gear.
Page 125: Onstar ® System
® OnStar System ® OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
Page 126 Available Services with Safe & Sound • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • AccidentAssist • Remote Door Unlock/Vehicle Alert ®...
Page 127 ® OnStar Virtual Advisor ® OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics.
Page 128: Universal Home Remote System
® OnStar service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well. Your vehicle must have a working electrical system (including adequate battery power) for the ® OnStar equipment to operate.
Page 129: (With One Triangular Led)
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 3521A-GTE05A.
Page 130: Operation (With Three Round Led)
Universal Home Remote System Operation (With Three Round LED) Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) above the Universal Home Remote System buttons, follow the instructions below. If there is one triangular LED above the Universal Home Remote System buttons, follow the instructions under Universal Home Remote System Operation (with one triangular LED).
Page 131 If you do not know if your garage door opener is a ﬁxed code or rolling code device, open your garage door opener’s remote control battery cover. Your garage door opener is a ﬁxed code device if there is a panel of switches. If not, your garage door opener is a rolling code device.
Page 132 Example of Switch Settings 2. Write down the eight to 12 coding switch settings from left to right. When the switch is in the up position, write “on,” and when a switch is in the down position, write “off”. If a switch is set between the up and down position, write “middle”.
Page 133 5. After entering the switch settings, press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves.
Page 134 2. Go to the garage. Locate the garage door motor head and press and release the “learn” button. After pressing the “learn” button, you have 10 to 30 seconds to complete Step 4 depending on your garage control unit. If you cannot locate the “learn”...
Page 135: Universal Home Remote System Operation
Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell the vehicle or terminate your lease. To erase either rolling code or ﬁxed code on the Universal Home Remote device, do the following: 1.
Page 136 Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming.
Page 137 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light.
Page 138 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.
Page 139: Storage Areas
Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2.
Page 140: Overhead Console
Overhead Console Your vehicle may have this feature. The overhead console may include reading lamps, a Universal Home Remote, and a moonroof switch. See the following for more information: • Reading Lamps on page 164. • Universal Home Remote System (With Three Round LED) on page 128 or Universal Home Remote System (With One Triangular LED) on page 129.
Page 141: Luggage Carrier
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control.
Page 142: Rear Floor Storage Lid
Rear Floor Storage Lid CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle has a rear cargo area with a removable storage lid.
Page 143: Cargo Tie Downs
To remove the cargo cover, do the following: 1. Release the cover from the latch posts and carefully roll it back up. 2. Squeeze one endcap and remove it from the pocket in the trim panel. 3. Remove the cargo cover from the other endcap so that you can remove the shade from the vehicle.
Page 144: Moonroof
Moonroof The vehicle may be equipped with a power sliding moonroof. The ignition must be turned to RUN, ACC, or Retained Accessory Power (RAP) must be active to operate it. See Retained Accessory Power (RAP) on page 108. The moonroof switch is located in the overhead console.
Page 145: Instrument Panel
Section 3 Instrument Panel Overview ... 148 Hazard Warning Flashers ... 150 Other Warning Devices ... 150 Horn ... 150 Tilt Wheel ... 151 Turn Signal/Multifunction Lever ... 151 Turn and Lane-Change Signals ... 152 Headlamp High/Low-Beam Changer ... 153 Flash-to-Pass ...
Page 146 Section 3 Tire Pressure Light ... 186 Malfunction Indicator Lamp ... 187 Oil Pressure Gage ... 190 Security Light ... 191 Cruise Control Light ... 191 Reduced Engine Power Light ... 191 Highbeam On Light ... 192 Service All-Wheel Drive Light ... 192 Check Gages Warning Light ...
Page 147 NOTES...
Page 148: Instrument Panel Overview
Instrument Panel Overview...
Page 149 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 172. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 151. C. Audio Steering Wheel Controls. See Audio Steering Wheel Controls on page 259. D.
Page 150: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel.
Page 151: Tilt Wheel
Tilt Wheel The steering wheel should be adjusted before you drive. The tilt lever is located to the left of the steering column, under the turn signal lever. It can be raised to the highest level to give your legs more room when you enter and exit the vehicle.
Page 152: Turn And Lane-Change Signals
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions let you signal a turn or a lane change. To signal a turn, move the lever all the way up or down.
Page 153: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on.
Page 154: Windshield Wipers
Windshield Wipers The lever on the right side of the steering column operates the windshield wipers. (Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it.
Page 155: Windshield Washer
Windshield Washer (Windshield Washer): To spray washer ﬂuid on the windshield, press the windshield washer paddle. The wipers will clear the window and then either stop or return to your preset speed. CAUTION: In freezing weather, do not use your washer until the windshield is warmed.
Page 156: Headlamp Washer
Headlamp Washer Your vehicle may be equipped with a headlamp washer system. The headlamp washers clear debris from the headlamp lenses by soaking the lens with ﬂuid, waiting for about ﬁve seconds, then rinsing the loose debris from the lenses. The headlamp washers are located under the headlamps.
Page 157 If you apply your brakes, the cruise control will shut off. CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads.
Page 158 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you do not need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate.
Page 159 Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills.
Page 160: Headlamps
Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. See Turn Signal/Multifunction Lever on page 151. (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has the following four positions: (On/Off): Turn the control to this position to turn off the Daytime Running Lamps (DRL)
Page 161: Daytime Running Lamps (Drl)
Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
Page 162: Fog Lamps
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems, so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system are only affected when the light sensor sees a change in lighting lasting longer than the delay.
Page 163: Instrument Panel Brightness
Instrument Panel Brightness Turn the knob to adjust the instrument panel lights. Turn the knob clockwise or counterclockwise to brighten or dim the interior lamps. Dome Lamps The dome lamps will automatically come on when you open a door, unless the dome lamp override button is pressed in.
Page 164: Entry Lighting
Entry Lighting The vehicle has entry lighting. When any door is opened, the dome lamps come on as long as the dome override lamp override button is not pressed in. When all the doors are closed, the lamps stay on for a short period of time and then turn off automatically.
Page 165: Battery Run-Down Protection
A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery.
Page 166: Accessory Power Outlet(S)
Accessory Power Outlet(s) With the accessory power outlets, you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle has three accessory power outlets. There are two outlets located below the climate controls and one outlet is on the rear of the center ﬂoor console.
Page 167: Climate Controls
Climate Controls Dual Automatic Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. When your vehicle is ﬁrst started and the climate control system is on, or if the climate control system has been turned on, the display will show the driver’s temperature setting for ﬁve seconds.
Page 168 Passenger’s Side Temperature Knob: Turn this knob clockwise or counterclockwise to manually raise or lower the temperature on the passenger’s side of the vehicle. The display will show the temperature setting decreasing or increasing and an arrow pointing toward the passenger. The passenger’s temperature setting can be set to match and link to the driver’s temperature setting by pressing and holding the AUTO button...
Page 169 Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the air conditioning operation and air outlet mode will be automatically controlled. The air conditioning compressor will run continuously when the outside temperature is over approximately 40°F (4°C).
Page 170 (Floor): This mode directs most of the air to the ﬂoor outlets. Some air also comes out of the defroster and side window outlets. The recirculation button cannot be selected in ﬂoor mode. (Recirculation): Press this button to turn recirculation mode on or off. When this button is pressed, an indicator light in the button will also come on to let you know that it is activated.
Page 171 If you turn the air conditioning off while in front defrost or defog mode, the air conditioning symbol will turn off, however, the A/C compressor will remain on to help de-humidify the air inside the vehicle. If one of the other modes is selected the compressor will then turn the A/C off until it is selected again or the AUTO button is pressed.
Page 172: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear): Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 173: Rear Climate Control System
Rear Climate Control System The lower buttons on the rear seat audio are used to adjust the rear seat climate controls. The temperature of the air coming through the rear outlets is determined by the front passenger’s temperature setting. (Fan) Press this button to adjust the fan speed.
Page 174: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 175: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically.
Page 176: Speedometer And Odometer
Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running.
Page 177: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will sound for several seconds to remind you buckle your safety belt. The driver safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more.
Page 178: Airbag Readiness Light
Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module.
Page 179: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your rearview mirror has a passenger airbag status indicator. United States Canada When the ignition key is turned to RUN or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 180 If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag.
Page 181 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off.
Page 182: Charging System Light
Charging System Light The charging system light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system.
Page 183: Brake System Warning Light
When the engine is running, the gage shows the condition of the charging system. The gage may transition from a higher to lower or a lower to higher reading. This is normal. Readings between the low and high warning zones indicate the normal operating range.
Page 184: Anti-Lock Brake System Warning Light
This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the light comes on while you are driving, pull off the road and stop carefully.
Page 185: Stabilitrak ® Service Light
® StabiliTrak Service Light This light will come on brieﬂy when the engine is started. This light will come on if a problem is detected in ® the StabiliTrak system. For more information see StabiliTrak page 271. StabiliTrak During most driving conditions, this light will not come on.
Page 186: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, the engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Page 187: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light Your vehicle has a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 188 This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: •...
Page 189 Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel.
Page 190: Oil Pressure Gage
Oil Pressure Gage United States The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range.
Page 191: Security Light
Security Light This light will come on brieﬂy when you turn the key toward START. ® See PASS-Key III Operation on page 104 for additional information regarding the security light. Cruise Control Light This light will come on when the cruise control is set.
Page 192: Highbeam On Light
Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 153. Service All-Wheel Drive Light This light should come on brieﬂy when you turn on the ignition, as a check to show you it is working.
Page 193: Gate Ajar Light
Gate Ajar Light If this light comes on, the liftgate or liftglass is not completely shut. Close the liftgate or liftglass. Never drive with the liftgate or liftglass even partially open. Fuel Gage United States When the ignition is on, the fuel gage tells you about how much fuel you have remaining.
Page 194: Driver Information Center (Dic)
Low Fuel Warning Light The light next to the fuel gage will come on brieﬂy when you are starting the engine. This light comes on when the fuel tank is low on fuel. To turn it off, add fuel to the fuel tank. See Fuel on page 324.
Page 195: Dic Operation And Displays
(Trip Information): Press this button to display the odometer, trip odometers, and timer. See DIC Operation and Displays on page 195 for more information. (Hazard): Press this button to turn the hazard warning ﬂashers on and off. See Hazard Warning Flashers on page 150 for more information.
Page 196 Fuel Information Button (Fuel Information): Press this button to scroll through the fuel range, fuel used, average fuel economy, and the engine oil life system. Fuel Range: Press the fuel information button until RANGE appears on the display. This mode shows the remaining distance you can drive without refueling.
Page 197 In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 334 and Scheduled Maintenance on page 450. Trip Information Button (Trip Information): Press this button to scroll through the odometer, trip odometers, tire pressures, and timer.
Page 198 Tire Pressures: Press the trip information button until TIRE PRESSURES appears on the display. This mode shows the tire pressure in pounds per square inch (psi) or kilopascals (kPa). Press the select button to scroll through the following information: • LF TIRE shows the tire pressure for the front driver’s side tire.
Page 199: Dic Warnings And Messages
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action.
Page 200 CHECK WASHER FLUID This message displays if the washer ﬂuid level is low. Adding washer ﬂuid to the windshield washer ﬂuid reservoir clears this message. See Windshield Washer Fluid on page 357. This message clears itself after 10 seconds, or you can press any of the DIC buttons, or the trip stem, to acknowledge this message and clear it from the DIC display.
Page 201 FRONT FOG LAMPS ON This message displays if the fog lamps are turned on. The message clears after 10 seconds. See Fog Lamps on page 162 and Turn Signal/ Multifunction Lever on page 151 for more information. FUEL LEVEL LOW This message displays and a chime sounds if the fuel level is low in the vehicle’s fuel tank.
Page 202 OIL PRESSURE LOW/STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible.
Page 203 SERVICE AIR BAG This message displays if there is a problem with the airbag system. Have your dealer inspect the system for problems. See Airbag Readiness Light on page 178 and Airbag System on page 64 for more information. Press any of the DIC buttons, or the trip stem, to acknowledge this message and clear it from the DIC display.
Page 204 SERVICE TIRE MONITOR This message displays if a part on the Tire Pressure Monitor (TPM) system is not working properly. If you drive your vehicle while any of the four sensors are missing or inoperable, the warning comes on in about 20 minutes. A sensor would be missing, for example, if you put different wheels on your vehicle without transferring the sensors.
Page 205: Dic Vehicle Customization
TIGHTEN FUEL CAP This message may display and a chime may sound if the vehicle’s fuel cap is not tightened properly. Fully reinstall the fuel cap. See Filling the Tank on page 326. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
Page 206 Press the customization button to scroll through the available customizable options. After pressing the customization button, VEHICLE SETTINGS momentarily displays before going to a customization option. Lock Doors Press the customization button until LOCK DOORS: IN GEAR appears in the display. To select your preference for automatic locking, press the select button while LOCK DOORS: IN GEAR is displayed on the DIC.
Page 207 Lock Feedback Press the customization button until LOCK FEEDBACK: BOTH appears in the display. To select your preference for the feedback you receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter, press the select button while LOCK FEEDBACK: BOTH is displayed on the DIC.
Page 208 UNLOCK FEEDBACK: OFF: There will be no feedback when unlocking the vehicle. Choose one of the available options and press the customization button while it is displayed on the DIC to select it and move on to the next feature. Headlamp Delay Press the customization button until HEADLAMP DELAY: 10 SEC appears in the display.
Page 209 Easy Exit Seat Press the customization button until EASY EXIT SEAT: OFF appears in the display. To select your preference for seat position exit, press the select button while EASY EXIT SEAT: OFF is displayed on the DIC. Pressing the select button will scroll through the following choices: EASY EXIT SEAT: OFF (default): No seat exit recall will occur.
Page 210 SEAT RECALL: ON REMOTE: The driver’s memory seat, mirrors, and adjustable pedals position you saved will be recalled when you unlock the vehicle with the Remote Keyless Entry (RKE) transmitter. Choose one of the available options and press the customization button while it is displayed on the DIC to select it and move on to the next feature.
Page 211 ALARM WARNING: OFF: There will be no alarm warning on activation. Choose one of the available options and press the customization button while your choice is displayed on the DIC to select it and move on to the next feature. For more information on alarm warning type, see Content Theft-Deterrent on page 102.
Page 212: Audio System(S)
If U.S. (ENGLISH) is chosen, all information will be displayed in English units. For example, distance will be displayed in miles (mi) and fuel economy in miles per gallon (MPG). If METRIC (km/L) is chosen, all information will be displayed in metric units.
Page 213: Setting The Time
Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: • Familiarize yourself with all of its controls. • Familiarize yourself with its operation. • Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers.
Page 214: Radio With Cd
Radio with CD XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and Canada. XM™ offers a large variety of coast-to-coast channels including music, news, sports, talk, traffic/weather (U.S. subscribers), and children’s programming.
Page 215 For XM™ (if equipped), press the DISP button while in XM™ mode to retrieve four different categories of information related to the current song or channel: Artist, Song Title, Category or PTY, Channel Number/Channel Name. To change the default on the display, press the DISP button until the desired option displays, then hold this knob for two seconds.
Page 216 (Information) (XM™ Satellite Radio Service and MP3 Features): If the current station has a message, the information symbol displays. Press this button to see the message. The message can display the artist, song title, call in phone numbers, etc. If the entire message is not displayed, parts of the message appears every three seconds.
Page 217 Setting the Tone (Bass/Treble) (Bass/Treble): Push and release this knob until BASS or TREB (treble) displays. Turn this knob to increase or to decrease the tone. The display shows the bass or the treble level. If a station is weak or has static, decrease the treble. To adjust the bass and the treble to the middle position, while in bass or treble, push and hold the tone knob.
Page 218 Finding a Category (CAT) Station (XM™ Satellite Radio Service Only) To select and ﬁnd a desired category perform the following: 1. Press the CAT button to activate category select mode. The current category displays. 2. Turn the tune knob to select a category. 3.
Page 219 If the ignition or radio is turned off with a CD in the player, it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source. When the CD is inserted, READING and the CD symbol displays.
Page 220 (Repeat): Press this pushbutton to hear a track over again. RPT ON displays. The current track continues to repeat. Press this pushbutton again to turn off repeat play. RPT OFF displays. (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order. RDM ON displays.
Page 221 Playing an MP3 CD-R Disc Your vehicle’s radio system may have the MP3 feature. If it has this feature, it is capable of playing an MP3 CD-R disc. For more information on how to play an MP3 CD-R disc, see Using an MP3 on page 233 later in this section.
Page 222: Radio With Six-Disc Cd
Radio with Six-Disc CD XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and Canada. XM™ offers a large variety of coast-to-coast channels including music, news, sports, talk, traffic/weather (U.S. subscribers), and children’s programming.
Page 223 Playing the Radio (Power): Press this knob to turn the system on and off. Turn this knob clockwise or counterclockwise to increase or to decrease the volume. DISP (Display): When the ignition is turned off, press this knob to display the time. For XM™...
Page 224 SEEK : Press and release the right or the left arrow to go to the next or to the previous station and stay there. The radio only seeks stations with a strong signal that are in the selected band. Press and hold either arrow for more than two seconds.
Page 225 Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2.
Page 226 Adjusting the Speakers (Balance/Fade) (Balance/Fade): To adjust the balance between the right and the left speakers, push and release this knob until BAL (balance) displays. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, push and release the tone knob until FADE displays.
Page 227 Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR displays, it means that the radio has not been conﬁgured properly for your vehicle and it must be returned to your dealer for service.
Page 228 If there is no apparent damage, try a known good CD. Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
Page 229 To load more than one CD but less than six, complete Steps 1 through 3. When ﬁnished loading CDs, press the LOAD button to cancel the loading function. The radio begins to play the last CD loaded. If more than one CD has been loaded, a number for each CD displays.
Page 230 (Reverse): Press this button to reverse within the track. (Fast Forward): Press this button to fast forward within the track. (Repeat): With the repeat setting, one track or an entire CD can be repeated. To use repeat, do the following: •...
Page 231 To scan all loaded CDs, press and hold either arrow for more than four seconds until CD SCAN displays and a beep sounds. Use this feature to listen to 10 seconds of the ﬁrst track of each loaded CD. Press either arrow again, to stop scanning. DISP (Display): Press this knob to see how long the current track has been playing.
Page 232 S-LIST FULL displays if you try to save more than 20 selections. To play the song list, press the song list button. One beep sounds and S-LIST displays. The recorded tracks begins to play in the order they were saved. Seek through the song list by using the SEEK SCAN arrows.
Page 233: Using An Mp3
CD Messages CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. •...
Page 234 The player is able to read and play a maximum of 50 folders, 50 playlists, 10 sessions, and 255 ﬁles. Long ﬁle names, folder names, or playlist names can use more disc memory space than necessary. To conserve space on the disc, minimize the length of the ﬁle, folder, or playlist names.
Page 235 Order of Play Tracks play in the following order: • Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist.
Page 236 If the ignition or radio is turned off while a CD is in the player, it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source.
Page 237 (Repeat): Press this pushbutton to hear a track over again. RPT On displays. The current track continues to repeat. Press this pushbutton again to turn off repeat play. RPT OFF displays. (Random): To random the tracks in the current folder or playlist, press and release this pushbutton.
Page 238 DISP (Display): Press this knob to switch between track mode, folder/playlist mode, and time of day mode. The display shows only eight characters, but there can be up to four pages of text. If there are more than eight characters in the song, folder, or playlist name, pressing this knob within two seconds takes the CD to the next page of text.
Page 239: Xm Radio Messages
XM Radio Messages If you have a Radio with CD, you will receive these radio display messages. Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code The encryption code in the receiver is being updated, and No Signl Loss of signal Loading...
Page 240 Radio Display Message No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Lock Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known...
Page 241 If you have a Radio with Six-Disc CD, you will receive these radio display messages. Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code The encryption code in the receiver is being updated, and No Signal Loss of signal Loading XM...
Page 242 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) If tuned to channel 0, this message alternates with the Unknown Radio ID not known (should only be if...
Page 243: Navigation/Radio System
Navigation/Radio System Your vehicle may have a navigation radio system. The navigation system has built-in features intended to minimize driver distraction. Technology alone, no matter how advanced, can never replace your own judgment. See the Navigation System manual for some tips to help you reduce distractions while driving.
Page 244 Headphones The RSE system includes two sets of wireless headphones. Each set of headphones has an ON/OFF control. An indicator light will illuminate on the headphones when they are on. If the light does not illuminate, the batteries may need to be replaced. See “Battery Replacement”...
Page 245 Stereo RCA Jacks The RCA jacks are located behind the video screen. The RCA jacks allow audio and video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Standard RCA cables, not included, are needed to connect the auxiliary device to the RCA jacks.
Page 246 The RSE system will always transmit the audio signal by infrared to the wireless headphones, if there is audio available. See “Headphones” previously for more information. The RSE system is capable of outputting audio to the vehicle speakers by using the radio. The RSE system may be selected as an audio source on the radio if the RSE system power is on.
Page 247 DVD Player The DVD player is located in the overhead console. The DVD player can be controlled by the buttons on the DVD player and/or by the buttons on the remote control. See “Remote Control” later in this section for more information. The DVD player power may be turned on when the ignition is in RUN, ACC, or when Retained Accessory Power (RAP) is active.
Page 248 DVD Player Buttons (Without Sunroof) (Power): Press this button to turn the RSE system on and off. The power indicator light will illuminate when the power is on. (Eject): Press this button to eject a DVD or CD. SRCE (Source): Press this button to switch between the DVD player and an auxiliary source.
Page 249 (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu. (Enter): Press this button to select the choices that are highlighted in any menu. DVD Player Buttons (With Sunroof) (Play/Pause): Press this button to start play of a DVD or CD. Press this button while a DVD or CD is playing to pause it.
Page 250 Stopping and Resuming Playback To stop playing a disc, press and release the stop button on the DVD player faceplate or the remote control. To resume playback, press the play/pause button on the DVD player faceplate or the remote control. The movie should resume play from where it was last stopped, if the disc has not been ejected and the stop button has not been pressed twice.
Page 251 Remote Control Buttons (Power): Press this button to turn the DVD player on and off. (Title): Press this button to return the DVD to the main menu of the DVD. (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu. (Set-up Menu): Press this button to adjust the color, tint, brightness, contrast, display mode, and dynamic range compression.
Page 252 (Previous Track/Chapter): Press this button to return to the start of the current track or chapter. Press this button again to return to the previous track or chapter. This button may not work when the DVD is playing the copyright information or the previews.
Page 253 (Fast Forward): Press this button to fast forward the DVD or CD. To stop fast forwarding, press this button again. This button may not work when the DVD is playing the copyright information or the previews. (Play/Pause): Press this button to start play of a DVD or CD.
Page 254 Problem Recommended Action No power. The ignition might not be in on or accessory. The parental control button might have been turned on. The power indicator light will ﬂash. Disc will not play. The system might be off. The parental control button might have been turned on.
Page 255 Problem Recommended Action After stopping the player, If the stop button was I push Play but pressed one time, the sometimes the DVD DVD player will resume starts where I left off and playing where the DVD sometimes at the was stopped.
Page 256 DVD Messages The following errors may be displayed on the video screen: Disc Format Error: This message will be displayed if a disc is inserted upside down, if the disc is not readable, or if the format is not compatible with the DVD player. Load/Eject Error: This message will be displayed if the disc is not properly loaded or ejected.
Page 257: Rear Seat Audio (Rsa)
Rear Seat Audio (RSA) This feature allows rear seat passengers to select and listen to any of the available radio sources: AM/FM, XM, CD, or DVD. However, a rear seat passenger cannot control a source selected on the radio by someone in the front of the vehicle.
Page 258: Theft-Deterrent Feature
SRCE (Source): Press this button to select an audio source: AM/FM, XM, CD, or DVD. The inactive CD, or DVD will remain safely inside the radio for future listening. There are sources that are internal to the radio, such as AM/FM, and CD and other sources to radio that are external, such as ®...
Page 259: Audio Steering Wheel Controls
Audio Steering Wheel Controls Some audio controls can be adjusted at the steering wheel. They include the following: SEEK : Press the forward or the back arrow to go to the next or to the previous radio station and stay there. The radio will only seek stations with a strong signal that are in the selected band.
Page 260: Radio Reception
Radio Reception You may experience frequency interference and static during normal radio reception if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 261: Care Of Your Cds And Dvds
Care of Your CDs and DVDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all.
Page 262 NOTES...
Page 263: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ... 264 Defensive Driving ... 264 Drunken Driving ... 265 Control of a Vehicle ... 268 Braking ... 268 Anti-Lock Brake System (ABS) ... 269 Braking in Emergencies ... 271 Limited-Slip Rear Axle ... 271 ®...
Page 264: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 18. CAUTION: Defensive driving really means “Be ready for anything.”...
Page 265: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 266 According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin, or vodka.
Page 267 But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent.
Page 268: Control Of A Vehicle
That means you can lose control of your vehicle. Adding non-Saab accessories can affect your vehicle’s performance. See Accessories and Modiﬁcations on page 322.
Page 269: Anti-Lock Brake System (Abs)
Once the power assist is used up, it may take longer to stop and the brake pedal will be harder to push. Adding non-Saab accessories can affect your vehicle’s performance. See Accessories and Modiﬁcations on page 322.
Page 270 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
Page 271: Braking In Emergencies
Remember: ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 272 When you ﬁrst start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle.
Page 273 STABILITRAK OFF — The driver can turn off ® StabiliTrak by pressing the StabiliTrak more than ﬁve seconds. The StabiliTrak will come on and STABILITRAK OFF will be displayed. For vehicles without a DIC, the ® StabiliTrak indicator light will come on. Momentarily pressing the StabiliTrak will return the system to the STABILITRAK ON ®...
Page 274 The following chart describes the StabiliTrak that will be displayed on the instrument panel cluster. Vehicles with a DIC ® StabiliTrak DIC Message Indicator Light None Solid Traction Control Off Solid StabiliTrak Blinking StabiliTrak Solid Service StabiliTrak StabiliTrak Solid Not Ready ®...
Page 275: All-Wheel Drive (Awd) System
® Notice: If the StabiliTrak light comes on due to heavy braking and/or because the traction control system has been continuously active, do not allow the wheel(s) of one axle to spin excessively. If you do, you may be causing damage to the transfer case.
Page 276: Steering
Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway. Adding non-Saab accessories can affect your vehicle’s performance. See Accessories and Modiﬁcations on page 322.
Page 277 Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 278: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 279 • Watch for traffic signs, pavement markings, and lines. If you can see a sign up ahead that might indicate a turn or an intersection, delay your pass. A broken center line usually indicates it is all right to pass, providing the road ahead is clear.
Page 280: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Page 281: Off-Road Driving
Off-Road Driving Your vehicle does not have features like added ground clearance, special underbody shielding, and a transfer case low gear range, things that are necessary for extended or severe off-road service. You should not drive off-road unless you are on a level, solid surface.
Page 282: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little.
Page 283 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking. It is wise to keep your wiping equipment in good shape and keep your windshield washer ﬂuid reservoir ﬁlled with washer ﬂuid.
Page 284 Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle.
Page 285: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: •...
Page 286: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 287: Before Leaving On A Long Trip
Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up.
Page 288: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 289 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system, and transmission.
Page 290 • Know how to go uphill. You may want to shift down to a lower gear. The lower gears help cool your engine and transmission, and you can climb the hill better. • Stay in your own lane when driving on two-lane roads in hills or mountains.
Page 291: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 380. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and reﬂective warning...
Page 292 Driving on Snow or Ice Most of the time, those places where the tires meet the road probably have good traction. However, if there is snow or ice between the tires and the road, you can have a very slippery situation.
Page 293 The Anti-Lock Brake System (ABS) improves your vehicle’s stability when you make a hard stop on a slippery road. Even though you have ABS, you will want to begin stopping sooner than you would on dry pavement. See Anti-Lock Brake System (ABS) on page 269.
Page 294 You can run the engine to keep warm, but be careful. CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 295: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
You will need a well-charged battery to restart the vehicle, and possibly for signaling later on with your headlamps. Let the heater run for a while. Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold.
Page 296: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right. That will clear the area around the front wheels. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Page 297 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 298 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 299 Example 1 Item Description Vehicle Capacity Weight for Example 1 Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Vehicle Capacity 1,000 lbs (453 kg) Weight for Example 2 Subtract...
Page 300 Example 3 Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight.
Page 301 This is called Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, cargo, and trailer tongue weight, if pulling a trailer. The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR).
Page 302: Towing
If you put things inside your vehicle like suitcases, tools, packages, or anything else they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop...
Page 303: Electronically Controlled Air Suspension System
Your vehicle was not designed to be towed with any of its wheels on the ground. If your vehicle must be towed, see “Towing Your Vehicle” earlier in this section. Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components.
Page 304 Overload Protection The air suspension system is equipped with overload protection. Overload protection is designed to protect the air suspension system, and it is an indicator to the driver that the vehicle is overloaded. When the overload protection mode is on, it will not allow damage to the air compressor.
Page 305: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
Page 306 If You Do Decide To Pull A Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Page 307 Use the following chart to ﬁnd the maximum trailer weight for your vehicle. Vehicle AWD (L6 Engine) AWD (V8 Engine) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversion.
Page 308 Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 309 After you’ve loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren’t, you may be able to get them right simply by moving some items around in the trailer. Trailering may be limited by the vehicle’s ability to carry tongue weight.
Page 310 But let’s say your speciﬁc vehicle is equipped with some of the latest options and you have a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. You may add 300 lbs (136 kg) to the front axle weight and 400 lbs (181 kg) to the rear axle weight.
Page 311 Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation label at the rear edge of the driver’s door or see Loading Your Vehicle on page 296 for more information.
Page 312 If you will be pulling a trailer that, when loaded, will weigh more than 4,000 lbs (1 814 kg) be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving.
Page 313 Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You cannot see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 119.
Page 314 Before you start, check all trailer hitch parts and attachments, safety chains, electrical connection, lamps, tires and mirror adjustment. If the trailer has electric brakes, start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working.
Page 315 Turn Signals When Towing a Trailer The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also ﬂash, telling other drivers you’re about to turn, change lanes or stop. When towing a trailer, the arrows on your instrument panel will ﬂash for turns even if the bulbs on the trailer are burned out.
Page 316 Parking on Hills CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged.
Page 317 If your vehicle is not equipped with the heavy-duty trailer connector, you can purchase one from your Saab dealer. The seven-wire harness contains the following trailer circuits: •...
Page 318 NOTES...
Page 319: Service And Appearance Care
Section 5 Service ... 322 Accessories and Modiﬁcations ... 322 California Proposition 65 Warning ... 322 Doing Your Own Service Work ... 323 Adding Equipment to the Outside of Your Vehicle ... 323 Fuel ... 324 Gasoline Octane ... 324 Gasoline Speciﬁcations ...
Page 320 Section 5 Windshield Replacement ... 377 Windshield Wiper Blade Replacement ... 377 Tires ... 380 Tire Sidewall Labeling ... 381 Tire Terminology and Deﬁnitions ... 385 Inﬂation - Tire Pressure ... 388 High-Speed Operation ... 390 Tire Pressure Monitor System ... 391 Tire Inspection and Rotation ...
Page 321 Section 5 Vehicle Identiﬁcation ... 433 Vehicle Identiﬁcation Number (VIN) ... 433 Service Parts Identiﬁcation Label ... 433 Electrical System ... 434 Add-On Electrical Equipment ... 434 Headlamps ... 434 Windshield Wiper Fuses ... 434 Service and Appearance Care Power Windows and Other Power Options ...
Page 322: Service
Saab accessories are designed to complement and function with other systems on your vehicle. Your Saab dealer can accessorize your vehicle using genuine Saab accessories. When you go to your Saab dealer and ask for Saab accessories, you will know that Saab-trained and supported service technicians will perform the work using genuine Saab accessories.
Page 323: Doing Your Own Service Work
Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task.
Page 324: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. To help keep your engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher.
Page 325: Additives
If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty. Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly.
Page 326: Fuels In Foreign Countries
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel may be hard to ﬁnd. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by your warranty.
Page 327 The tethered fuel cap is located behind a hinged fuel door on the driver’s side of the vehicle. To remove the fuel cap, turn it slowly counterclockwise. While refueling, hang the tethered fuel cap from the hook on the fuel door. CAUTION: If you spill fuel and then something ignites it, you could be badly burned.
Page 328: Filling A Portable Fuel Container
There may also be a light that comes on in the instrument panel to let you know if your gas cap is not properly installed. See Check Gas Cap Light on page 194 for more information. CAUTION: If a ﬁre starts while you are refueling, do not remove the nozzle.
Page 329: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: Things that burn can get on hot engine parts and start a ﬁre. These include liquids like fuel, oil, coolant, brake ﬂuid, windshield washer and other ﬂuids, and plastic or rubber. You or others could be burned.
Page 330: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 4.2L L6 engine, here is what you will see:...
Page 331 A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 339. B. Engine Coolant Recovery Tank. See Cooling System on page 349. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 357. D. Power Steering Fluid Reservoir. See Power Steering Fluid on page 356.
Page 332 When you open the hood on the 5.3L V8 engine, here is what you will see:...
Page 333 A. Engine Coolant Recovery Tank. See Cooling System on page 349. B. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 339. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 357. D. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 334.
Page 334: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 335 If the oil is below the cross-hatched area (L) for the 4.2L L6 engine or below the cross-hatched area at the tip of the dipstick for the 5.3L V8 engine, you will need to add at least one quart/liter of oil. But you must use the right kind.
Page 336 What Kind of Engine Oil to Use Look for two things: • GM6094M Your vehicle’s engine requires oil meeting standard GM6094M. You should look for and use only an oil that meets standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 337: Engine Oil Life System
You should look for this information on the oil container, and use only those oils that are identiﬁed as meeting standard GM6094M and have the starburst symbol on the front of the oil container. Notice: Use only engine oil identiﬁed as meeting standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol.
Page 338 When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE ENGINE OIL message will come on in the Driver Information Center (DIC). See DIC Warnings and Messages on page 199. Change the oil as soon as possible within the next 600 miles (1 000 km).
Page 339: Engine Air Cleaner/Filter
What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
Page 340 How to Inspect To inspect the air cleaner/ﬁlter, remove the ﬁlter from the vehicle and lightly shake the ﬁlter to release loose dust and dirt. If the ﬁlter remains caked with dirt, a new ﬁlter is required. To inspect or replace the ﬁlter, do the following: 1.
Page 341: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check and Change Automatic Transmission Fluid A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 452, and be sure to use the transmission ﬂuid listed in Recommended Fluids and Lubricants on page 458.
Page 342 A cold ﬂuid check can be made after the vehicle has been sitting for eight hours or more with the engine off, but this is used only as a reference. Let the engine run at idle for ﬁve minutes if outside temperatures are 50°F (10°C) or more.
Page 343 3. Check both sides of the dipstick, and read the lower level. The ﬂuid level must be in the COLD area, below the cross-hatched area, for a cold check or in the HOT or cross-hatched area for a hot check. Be sure to keep the dipstick pointed down to get an accurate reading.
Page 344: Engine Coolant
Engine Coolant The cooling system in your vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in your vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, if you add only DEX-COOL life coolant.
Page 345 CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning.
Page 346 Checking Coolant The engine coolant recovery tank is in the engine compartment on the passenger’s side of the vehicle. The cap has this symbol on it. See Engine Compartment Overview on page 330 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at FULL COLD, or a little higher.
Page 347: Radiator Pressure Cap
CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Occasionally check the coolant level in the radiator.
Page 348 If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 349: Cooling System
If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning does not come back on, you can drive normally. If the warning continues and you have not stopped, pull over, stop, and park your vehicle right away.
Page 350 5.3L V8 Engine A. Coolant Recovery Tank B. Radiator Pressure Cap C. Engine Fan If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. The coolant level should be at least up to the FULL COLD mark.
Page 351 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant.
Page 352 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at the FULL COLD mark, add a 50/50 mixture of clean, drinkable water ® and DEX-COOL engine coolant at the coolant recovery tank.
Page 353 If the overheat warning continues, there is one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 354 3. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck. See Engine Coolant on page 344 for more information about the proper coolant mixture. ® 4. Then ﬁll the coolant recovery tank to the FULL COLD mark.
Page 355: Engine Fan Noise
6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL coolant mixture through the ﬁller neck until the level reaches the base of the ﬁller neck.
Page 356: Power Steering Fluid
Power Steering Fluid See Engine Compartment Overview on page 330 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem.
Page 357: Windshield Washer Fluid
Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 358: Brakes
Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 330 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 359 Checking Brake Fluid You can check the brake ﬂuid without taking off the cap. Look at the brake ﬂuid reservoir. The ﬂuid level should be above MIN. If it is not, have your brake system checked to see if there is a leak.
Page 360 Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 361: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality brake parts.
Page 362: Jump Starting
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( ) cable from the battery. This will help keep your battery from running down. CAUTION: Batteries have acid that can burn you and gas that can explode.
Page 363 Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged.
Page 364 4. Open both hoods and locate the batteries. Find the positive (+) and negative ( ) terminals on each battery. Your vehicle has a remote negative ( ) jump starting terminal. You should always use this remote terminal instead of the terminal on the battery. The remote negative ( ) terminal is located on the front engine lift bracket on vehicles with the 4.2L L6 engine or the engine accessory...
Page 365 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 366 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery. Use a remote negative ( ) terminal if the vehicle has one. Do not let the other end touch anything until the next step.
Page 367 Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 368: All-Wheel Drive
All-Wheel Drive When to Check Lubricant It is not necessary to regularly check ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a...
Page 369: Rear Axle
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 370: Front Axle
Front Axle When to Check Lubricant It is not necessary to regularly check front axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 371: Headlamp Aiming
Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in an accident, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if it is difficult to see the lane markers (for horizontal aim), or if oncoming drivers ﬂash their high-beam headlamps at you (for vertical aim).
Page 372: Halogen Bulbs
Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. Headlamps To replace one of these bulbs, do the following: 1.
Page 373 4. Remove the bulb cover for the high beam (A) and low beam (B) bulbs. 5. Remove the bulb socket that needs to be replaced by turning it counterclockwise. 6. Disconnect the electrical connector from the old bulb. 7. Plug the electrical connector into the new bulb using care not to touch the glass with your ﬁngers.
Page 374: Front Turn Signal, Sidemarker And Parking Lamps
Front Turn Signal, Sidemarker and Parking Lamps To replace one of these bulbs, do the following: 1. Follow Steps 1 through 3 under Headlamps on page 372 to access the front turn signal, sidemarker or parking lamp. 2. Turn the bulb socket counterclockwise and remove it from the lamp assembly.
Page 375 To replace one of these bulbs, do the following: 1. Open the liftgate. See Liftgate/Liftglass on page 98 for more information. 2. Remove the screws 3. Pull the taillamp assembly away from the vehicle. 4. Turn the bulb socket counterclockwise to remove it from the taillamp assembly.
Page 376: License Plate Lamp
License Plate Lamp To replace one of these bulbs, do the following: 1. Remove the two screws holding the license plate lamp lens. 2. Pull the lens away from the lamp assembly. 3. Pull the old bulb straight out from the bulb socket.
Page 377: Windshield Replacement
Windshield Replacement Your vehicle is equipped with an acoustic windshield. If you ever have to have your windshield replaced be sure to get an acoustic windshield so you will continue to have the beneﬁts an acoustic windshield can provide. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking.
Page 378 3. Remove the insert from the blade assembly. The insert has two notches at one end that are locked by the bottom claws of the blade assembly. At the notched end, pull the insert from the blade assembly. 4. To install the new wiper insert, slide the insert (D), notched end last, into the end with two blade claws (A).
Page 379 Backglass Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the park rest position. 2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle.
Page 380: Tires
Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your Saab Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle.
Page 381: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P-Metric and a LT-Metric tire sidewall. Passenger (P-Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 382 (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information, see Uniform Tire Quality Grading on page 400.
Page 383 (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) Dual Tire Maximum Load: Maximum load that can be carried and the maximum pressure needed to support that load when used in a dual conﬁguration.
Page 384 Tire Size The following examples show the different parts of a tire size. Passenger (P-Metric) Tire Light Truck (LT-Metric) Tire (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 385: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Page 386 Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles.
Page 387 Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead.
Page 388: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 389 When to Check Check your tires once a month or more. Also, check the tire pressure of the spare tire. How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them.
Page 390: High-Speed Operation
High-Speed Operation CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inﬂation pressure adjustment for high speed operation.
Page 391: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. TPMS sensors are mounted on each tire and wheel assembly, except the spare tire. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle.
Page 392 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is signiﬁcantly under-inﬂated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inﬂate them to the proper pressure.
Page 393 Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. The Tire and Loading Information label (tire information placard) shows the size of your vehicle’s original tires and the correct inﬂation pressure for your vehicle’s tires when they...
Page 394 You will have two minutes to match the ﬁrst tire/wheel position, and ﬁve minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the ﬁrst tire and wheel, or more than ﬁve minutes to match all four tire and wheel positions the matching process stops and you will need to start over.
Page 395 9. After hearing the conﬁrming horn chirp for the driver’s side rear tire, check to see if the TPMS warning light is still ﬂashing. If yes, turn the ignition switch to LOCK to exit the sensor matching process. If the TPMS warning light is not ﬂashing, the ﬁve minute time limit has passed and you will need to start the process over beginning with Step 1.
Page 396: Tire Inspection And Rotation
Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 397 and Wheel Replacement on page 402 for more information.
Page 397: When It Is Time For New Tires
Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Speciﬁcations on page 445. CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 398: Buying New Tires
Tire Performance Criteria Speciﬁcation (TPC Spec) system rating. If you need replacement tires, Saab strongly recommends that you get tires with the same TPC Spec rating. This way, your vehicle will continue to have tires...
Page 399 CAUTION: If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed...
Page 400: Different Size Tires And Wheels
You may increase the chance that you will crash and suffer serious injury. Only use Saab speciﬁc wheel and tire systems developed for your vehicle, and have them properly installed by a Saab certiﬁed technician.
Page 401 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 402: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked.
Page 403 CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Page 404: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 405 You may also have an air inﬂator kit that is located in the rear ﬂoor storage compartment. It includes a 22 ft (6.7 m) hose with three nozzle adapters. To use the accessory inﬂator, do the following: 1. Attach the appropriate nozzle adapter to the end of the hose if required.
Page 406: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag...
Page 407 CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1.
Page 408: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The jacking equipment you will need is stored under the rear seat on the passenger’s side of the vehicle. See Rear Seat Operation on page 16 for more information. To release the jack from its holder, turn the knob on the jack counterclockwise to lower the jack head.
Page 409 The following instructions explain how to remove the underbody-mounted spare located underneath your vehicle. Notice: If you remove or restow a tire from/to the storage position under the vehicle when it is supported by a jack, you could damage the tire and/or your vehicle.
Page 410: Removing The Flat Tire And Installing The Spare Tire
5. Tilt the retainer at the end of the cable when the tire has been completely lowered, and pull it through the wheel opening. 6. Pull the tire out from under the vehicle. Notice: If you drive away before the spare tire or secondary latch system cable has been reinstalled, you could damage your vehicle.
Page 411 2. Using the wheel wrench, loosen all the wheel nuts. Do not remove them yet. 3. Turn the jack adjusting knob clockwise by hand to raise the jack lift head. 4. Place the handle, extension, and wheel wrench onto the jack. Front Position A.
Page 412 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 413 7. Remove all the wheel nuts and take off the ﬂat tire. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after time. The wheel could come off and cause an accident. CAUTION: (Continued) CAUTION: (Continued) When you change a wheel, remove any...
Page 414 9. Place the spare tire on the wheel-mounting surface. CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 10. Put the nuts on by hand. Make sure the rounded end is toward the wheel.
Page 415 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new original equipment wheel nuts.
Page 416: Secondary Latch System
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stored with the valve stem pointing up.
Page 417 To release the spare tire from the secondary latch, do the following: 1. Check under the 2. If visible, ﬁrst try to tighten the cable by turning the wheel wrench clockwise until you hear two clicks or feel it skip twice. You cannot overtighten the cable.
Page 418 6. Attach the jack handle, extension(s) and the wheel wrench to the jack and place it under the vehicle towards the front of the rear bumper. Position the center lift point of the jack under the center of the spare tire. 7.
Page 419 12. Be sure that the socket end of the extension connects to the hoist shaft. Turn the wheel wrench counterclockwise to lower the spare the rest of the way. 13. Tilt the retainer at the end of the cable and pull it through the wheel opening.
Page 420: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 421 Follow this diagram to store the underbody-mounted ﬂat or spare tire. A. Wheel Wrench B. Hoist Shaft C. Extension D. Retainer E. Spare or Flat Tire (Valve Stem Pointed Up) 1. Put the tire (E) on the ground at the rear of the vehicle.
Page 422 6. Make sure the tire is stored securely. Push, pull (A), and then try to turn (B) the tire. If the tire moves, use the wheel wrench and socket end of the extension to tighten the cable. 7. Return the equipment to the proper location in the vehicle as shown next.
Page 423: Spare Tire
Spare Tire Your vehicle, when new, had a fully-inﬂated spare tire. A spare tire may lose air over time, so check its inﬂation pressure regularly. See Inﬂation - Tire Pressure on page 388 and Loading Your Vehicle on page 296 for information regarding proper tire inﬂation and loading your vehicle.
Page 424 When cleaning your vehicle’s interior, only use cleaners speciﬁcally designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately.
Page 425: Fabric/Carpet
• Do not heavily saturate your upholstery while cleaning. • Damage to your vehicle’s interior may result from the use of many organic solvents such as naptha, alcohol, etc. Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt.
Page 426: Leather
Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather.
Page 427: Care Of Safety Belts
Be sure to rinse the vehicle well, removing all soap residue completely. Approved cleaning products can be obtained from your Saab dealer. See Vehicle Care/Appearance Materials on page 432. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives.
Page 428: Cleaning Exterior Lamps/Lenses
Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint ﬁnish. You can get Saab-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 432. If your vehicle has a “basecoat/clearcoat” paint ﬁnish, the clearcoat gives more depth and gloss to...
Page 429: Windshield, Backglass, And Wiper Blades
The repairs would not be covered by your warranty. Use only Saab-approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water.
Page 430: Tires
Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your Saab dealer. Larger areas of ﬁnish damage can be corrected in your Saab dealer’s body and paint shop.
Page 431: Underbody Maintenance
Although no defect in the paint job causes this, Saab will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs ﬁrst.
Page 432: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Removes tar, road oil, Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. White Sidewall Removes soil and black Tire Cleaner marks from whitewalls.
Page 433: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 434: Electrical System
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 435: Power Windows And Other Power Options
Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens, protecting the circuit until the problem is ﬁxed or goes away. Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers.
Page 436 Fuses Electronically Controlled Air Suspension Passenger’s Side Headlamp High-Beam 4.2L L6 Engine Usage Fuses Usage Passenger’s Side Headlamp Low-Beam Trailer Back-Up...
Page 437 Fuses Usage Driver’s Side Headlamp High-Beam Driver’s Side Headlamp Low-Beam Windshield Wiper Automatic Transfer Case Windshield Washer Powertrain Control Module B Fog Lamps Stoplamp Cigarette Lighter Electric Adjustable Pedals Ignition B Airbag System Electric Brake Cooling Fan Horn Ignition E Electronic Throttle Control Fuses Usage...
Page 438 J-Case Fuses Trailer Stoplamp/Turn Signal Trailer Anti-lock Brake System Ignition A Driver’s Side Headlamp Blower Motor Air Pump Passenger’s Side Headlamp Vehicle Stability Enhancement System (StabiliTrak Relays Headlamp Washer Rear Windshield Wiper/Washer Fog Lamps Horn Fuel Pump Usage Relays ® Usage Usage Windshield Washer...
Page 439 Fuses Usage Electrically Controlled Air Suspension Passenger’s Side Headlamp High-Beam 5.3L V8 Engine Fuses Passenger’s Side Headlamp Low-Beam Trailer Back-Up Usage...
Page 440 Fuses Driver’s Side Headlamp High-Beam Driver’s Side Headlamp Low-Beam Windshield Wiper Automatic Transfer Case Windshield Washer Powertrain Control Module B Fog Lamps Stoplamp Cigarette Lighter Ignition Coils Transmission Control Module/Canister Ignition B Airbag System Electric Brake Cooling Fan Horn Ignition E Electronic Throttle Control Instrument Panel Cluster/Driver Information Center...
Page 441 J-Case Fuses Usage Trailer Turn Signal, Stoplamps Trailer Anti-lock Brake System Ignition A Blower Motor Driver’s Side Headlamp Passenger’s Side Headlamp Vehicle Stability Enhancement System (StabiliTrak Relays Usage Headlamp Washer Rear Wiper Fog Lamps Horn Fuel Pump Windshield Washer Relays ®...
Page 442: Rear Underseat Fuse Block
Rear Underseat Fuse Block The rear underseat fuse block is located on the driver’s side of the vehicle, under the second row seat. Pull the seat cushion forward to access the fuse block.
Page 443 Fuses Usage Passenger Door Control Module Driver Door Control Module Liftgate Module 2 Truck Body Controller 3 Blank Blank Truck Body Controller 2 Power Seats Rear Wiper Driver Door Module Ampliﬁer Passenger Door Module Blank Driver Side Rear Parking Lamps Fuses Usage Blank...
Page 444 Fuses Accessory Parking Lamps Truck Body Controller Accessory Truck Body Controller 5 Front Wipers Ignition 3 Vehicle Stop Transmission Control Module Heat Ventilation Air Conditioning B Front Parking Lamps Rear Left Turn Signal Heat, Ventilation, Air Conditioning 1 Front Right Turn Signal Usage Fuses Usage...
Page 445: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 458 for more information. Application Air Conditioning Refrigerant R134a Cooling System 4.2L L6 Engine 5.3L V8 Engine Engine Oil with Filter 4.2L L6 Engine 5.3L V8 Engine Fuel Tank...
Page 446 Engine VORTEC™ 4.2L L6 VORTEC™ 5.3L V8 Engine Speciﬁcations VIN Code Transmission Automatic Automatic Spark Plug Gap 0.040 inches (1.01 mm) 0.040 inches (1.01 mm)
Page 447: Maintenance Schedule
Section 6 Maintenance Schedule ... 448 Introduction ... 448 Maintenance Requirements ... 448 Your Vehicle and the Environment ... 448 Using the Maintenance Schedule ... 448 Scheduled Maintenance ... 450 Additional Required Services ... 452 Maintenance Footnotes ... 453 Maintenance Schedule Owner Checks and Services ...
Page 448: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.
Page 449 Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your dealer.
Page 450: Scheduled Maintenance
The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 458 and Normal Maintenance Replacement Parts on page 460. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Page 451 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 334. Reset oil life system. See Engine Oil Life System on page 337. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter.
Page 452: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 453: Maintenance Footnotes
Service and Miles (Kilometers) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (l). Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc.
Page 454 (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 455: Owner Checks And Services
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure the safety, dependability, and emission control performance of your vehicle. Your dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once.
Page 456: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2.
Page 457 Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position. • The ignition should turn to LOCK only when the shift lever is in PARK (P). •...
Page 458: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets Standard GM6094M and displays the American Petroleum Institute Engine Oil Certiﬁed for Gasoline Engines starburst symbol.
Page 459 Usage Fluid/Lubricant SAE 75W-90 Synthetic Axle Lubricant (Part No. U.S. 12378261, in Canada 10953455) meeting speciﬁcations. With a complete drain Rear Axle and reﬁll add 4 ounces (118 ml) of Limited-Slip Axle Lubricant Additive (Part No. U.S. 1052358, in Canada 992694) where required. See Rear Axle on page 369.
Page 460: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Automatic Transmission Filter Kit Engine Air Cleaner/Filter Engine Oil Filter 4.2 L L6 Engine 5.3L V8 Engine Spark Plugs 4.2L L6 Engine 5.3L V8 Engine Wiper Blades...
Page 461: Engine Drive Belt Routing
Engine Drive Belt Routing 5.3L V8 Engine 4.2L V6 Engine...
Page 462: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 448. Any additional information from Owner Checks and Services on page 455 can be added on the following record pages.
Page 463 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II...
Page 464 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II...
Page 465: Customer Assistance Information
Customer Assistance Information Reporting Safety Defects ... 479 Reporting Safety Defects to the United States Government ... 479 Reporting Safety Defects to the Canadian Government ... 479 Reporting Safety Defects to Saab ... 480 Service Publications Ordering Information ... 480...
Page 466: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Saab. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 467: Online Owner Center
Saab Consumer’s Guide. Online Owner Center Online Owner Center (United States only) The Owner Center is a resource for your Saab ownership needs. Speciﬁc vehicle information can be found in one place. The Online Owner Center allows you to: •...
Page 468: Customer Assistance For Text Telephone (Tty) Users
1-800-263-3830.) Customer Assistance Offices Saab encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Saab, refer to the addresses below. United States — Customer Assistance Saab Customer Assistance Center Saab Cars USA, Inc.
Page 469: Roadside Assistance Program
Service available 24 hours a day, 365 days a year. Saab has a strong commitment to customer satisfaction and has established the Saab Roadside Assistance Program. As the owner of a new Saab vehicle, you are automatically enrolled in the Saab Roadside Assistance program. This value-added...
Page 470 The following services are provided in the U.S. during the Bumper-to-Bumper warranty period and, in Canada, during the Base Warranty coverage period of the New Vehicle Limited Warranty, up to a maximum coverage of $100. • Fuel Delivery: Delivery of enough fuel for the customer to get to the nearest service station (approximately $5 in the U.S.
Page 471 Pre-authorization, original detailed receipts and a copy of the repair order are required. In some instances, mechanical failures may be covered under the Saab Bumper-to-Bumper warranty, for U.S. customers, and the duration of the Base Warranty, for Canadian customers, of the new Vehicle Limited Warranty. However,...
Page 472 Remember, we are only a phone call away. Saab and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 473: Vehicle Data Collection And Event Data Recorders
To read this information, special equipment is needed and access to the vehicle or the device that stores the data is required. Saab will not access information about a crash event or share it with others other than: •...
Page 474: Collision Damage Repair
Genuine Saab Collision parts are your best ® , please choice to assure that your vehicle’s designed appearance, durability and safety are preserved. The use of Genuine Saab parts can help maintain your Saab New Vehicle Warranty.
Page 475 In most cases, the parts being recycled are from undamaged sections of the vehicle. A recycled original equipment Saab part, may be an acceptable choice to maintain your vehicle’s originally designed appearance and safety performance, however, the history of these parts is not known.
Page 476 Insuring Your Vehicle Protect your investment in your Saab vehicle with comprehensive and collision insurance coverage. There are signiﬁcant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your Saab vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
Page 477 • Choose a reputable collision repair facility for your vehicle. Whether you select a Saab dealer or a private collision repair facility to ﬁx the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time.
Page 478 Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, Saab recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Page 479: Reporting Safety Defects
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors.
Page 480: Reporting Safety Defects To Saab
Saab cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, the Service Bulletin reference number can be obtained by contacting your Saab dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 481 Current and Past Model Order Forms Technical Service Bulletins and Manuals are available for current and past model Saab 9-7x vehicles. To request an order form, please specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123...
Page 482 NOTES...
Page 483 Accessories and Modiﬁcations ... 322 Accessory Inﬂator ... 404 Accessory Power Outlet(s) ... 166 Adding Equipment to Your Airbag-Equipped Vehicle ... 81 Additives, Fuel ... 325 Add-On Electrical Equipment ... 434 Adjustable Throttle and Brake Pedal ... 110 Air Cleaner/Filter, Engine ... 339 Air Conditioning ...
Page 484 Appearance Care (cont.) Vehicle Care/Appearance Materials ... 432 Washing Your Vehicle ... 427 Weatherstrips ... 427 Windshield, Backglass, and Wiper Blades ... 429 Audio System(s) ... 212 Audio Steering Wheel Controls ... 259 Care of Your CD and DVD Player ... 261 Care of Your CDs and DVDs ...
Page 485 Bulb Replacement (cont.) Replacement Bulbs ... 376 Taillamps, Turn Signal, Sidemarker, Stoplamps, and Back-Up Lamps ... 374 Buying New Tires ... 398 Calibration ... 121, 123 California Fuel ... 324 California Proposition 65 Warning ... 322 Canadian Owners ... 3 Capacities and Speciﬁcations ...
Page 486 Customer Assistance for Text Telephone (TTY) Users ... 468 Customer Assistance Offices ... 468 Customer Satisfaction Procedure ... 466 Reporting Safety Defects to Saab ... 480 Reporting Safety Defects to the Canadian Government ... 479 Reporting Safety Defects to the United States Government ...
Page 487 Door Delayed Locking ... 94 Locks ... 92 Power Door Locks ... 93 Programmable Automatic Door Locks ... 94 Rear Door Security Locks ... 97 Driver Position, Safety Belt ... 24 Driver Information Center (DIC) ... 194 DIC Operation and Displays ... 195 DIC Vehicle Customization ...
Page 488 Engine (cont.) Oil Life System ... 337 Overheating ... 347 Reduced Power Light ... 191 Starting ... 108 Entry Lighting ... 164 Event Data Recorders (EDR) ... 473 Exit Lighting ... 164 Extender, Safety Belt ... 37 Filter Engine Air Cleaner ... 339 Finish Damage ...
Page 489 Gage Check Gages Warning Light ... 192 Engine Coolant Temperature ... 186 Fuel ... 193 Oil Pressure ... 190 Speedometer ... 176 Tachometer ... 176 Voltmeter Gage ... 182 Garage Door Opener ... 128, 129 Gasoline Octane ... 324 Speciﬁcations ... 324 Gate Ajar Light ...
Page 490 Ignition Positions ... 107 Infants and Young Children, Restraints ... 40 Inﬂation - Tire Pressure ... 388 Instrument Panel Overview ... 148 Instrument Panel (I/P) Brightness ... 163 Cluster ... 175 Jump Starting ... 362 Keyless Entry System ... 89 Keys ...
Page 491 Light (cont.) Low Fuel Warning ... 194 Malfunction Indicator ... 187 Passenger Airbag Status Indicator ... 179 Passenger Safety Belt Reminder ... 177 Reduced Engine Power ... 191 Safety Belt Reminder ... 177 Security ... 191 Service All-Wheel-Drive ... 192 ®...
Page 492 Memory Seat, Mirrors, and Pedals ... 11 Message DIC Warnings and Messages ... 199 Mirrors Automatic Dimming Rearview with Compass ... 123 Automatic Dimming Rearview with ® OnStar and Compass ... 121 Outside Convex Mirror ... 124 Outside Curb View Assist Mirror ... 124 Outside Heated Mirrors ...
Page 493 Paint, Damage ... 430 Park (P) Shifting Into ... 117 Shifting Out of ... 118 Parking Brake ... 116 Over Things That Burn ... 118 Passenger Airbag Status Indicator ... 179 Passenger Sensing System ... 74 Passing ... 278 ® PASS-Key III ...
Page 494 Removing the Spare Tire and Tools ... 408 Replacement Bulbs ... 376 Replacement, Windshield ... 377 Reporting Safety Defects Canadian Government ... 479 Saab ... 480 United States Government ... 479 Restraint System Check Checking the Restraint Systems ... 82 Replacing Restraint System Parts After a Crash ...
Page 495 Safety Belt Passenger Reminder Light ... 177 Pretensioners ... 37 Reminder Light ... 177 Safety Belts Care of ... 427 Driver Position ... 24 How to Wear Safety Belts Properly ... 23 Questions and Answers About Safety Belts ... 22 Rear Safety Belt Comfort Guides ...
Page 496 Spare Tire ... 423 Accessory Inﬂator ... 404 Installing ... 410 Removing ... 408 Storing ... 420 Speciﬁcations, Capacities ... 445 Speedometer ... 176 ® StabiliTrak System ... 271 ® StabiliTrak Indicator Light ... 185 ® StabiliTrak Service Light ... 185 Starting Your Engine ...
Page 497 Tires (cont.) Pressure Monitor System ... 391 Removing the Flat Tire ... 410 Removing the Spare Tire and Tools ... 408 Secondary Latch System ... 416 Spare Tire ... 423 Storing a Flat or Spare Tire and Tools ... 420 Tire Sidewall Labeling ...
Page 498 Warning Lights, Gages and Indicators ... 174 Warnings DIC Warnings and Messages ... 199 Hazard Warning Flashers ... 150 Other Warning Devices ... 150 Safety and Symbols ... 4 Vehicle Damage ... 5 Wheels Alignment and Tire Balance ... 402 Different Size ...

Saab 2007 9-7X Owner's Manual

Table of Contents

Section 1 Seats and Restraint Systems

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar ® System

Universal Home Remote System

Storage Areas

Moonroof

Section 3 Instrument Panel

Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Bulb Replacement

Headlamp Aiming

Windshield Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Saab 2007 9-7X

Summary of Contents for Saab 2007 9-7X