TABLE OF CONTENTS PAGE PAGE 1 Safety Precautions -----------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Flash P.C.B.----------------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices ----------5 2.2.
1 Safety Precautions 1.1. General Guidelines 1.3. Leakage Current Hot Check 1. IMPORTANT SAFETY NOTICE (See Figure 1.) There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Flash P.C.B. CAUTION: 1. Be sure to discharge the capacitor on FLASH P.C.B.. 2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
2.3.2.3. How to Replace the Fuse A replacement fuse cover can be purchased from your local Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
It should be disposed of in waste products destined for burial rather than incineration. NOTE: Above caution is applicable for a battery pack which is for HDC-HS700 series, as well. 1. Battery Pack for this model. 2. Button-type battery for Remote controller (CR2025: Being supplied from Energy Company, Panasonic Corporation)
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.) 2. The following category is /are recycle module part. Please send it/them to Central Repair Center. • MAIN P.C.B. (VEP03H98AN: HDC-HS700P/PC/PU/GT) • MAIN P.C.B. (VEP03H98AP: HDC-HS700EB/EC/EF/EG/EP)
3.4. How to Define the Model Suffix (NTSC or PAL model) There are seven kinds of HDC-HS700. • a) HDC-HS700P • b) HDC-HS700PC • c) HDC-HS700EB/EC/EF/EG/EP/GN • d) HDC-HS700EE • e) HDC-HS700GT • f) HDC-HS700PU/GC What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..
3.5. Precautions for Handling HDD 1. Handle HDD very carefully to prevent the static electricity and shock. 2. Set the HDD quickly after taking it out from the package. Make sure to put the HDD on buffer materials, etc. 3.5.1. Precautions at incoming process and for opening packages...
Page 12
3.5.3. Precautions for inserting and removing HDD FPC Make sure to use the tool (LSVQ0112) when locking and unlocking the lock lever of HDD FPC connector. Do not lock the lock lever without inserting HDD FPC. Otherwise, the connector may be damaged.
Page 13
Make sure to use the tool (LSVQ0112) when opening and closing the lock lever. When install the HDD to main unit, necessary install the HDD FPC and HDD cushion.
Battery release lever [BATT] Battery holder 10 DC input terminal [DC IN] Always use the supplied AC adaptor or a genuine Panasonic AC adaptor. 11 HDMI mini connector [HDMI] 12 USB terminal [ 13 AV multi connector Use the AV multi cable (only the supplied cable).
Page 19
32 Tripod receptacle 33 Photoshot button [ 35 36 34 Zoom lever [W/T] (In Motion Picture Recording Mode or Still Picture Recording Mode) Thumbnail display switch [ Volume lever [ VOL ] (In Playback Mode) 35 HDD access lamp [ACCESS HDD] 36 Status indicator 37 Internal microphones 38 Recording start/stop button...
Page 20
Selecting a mode Change the mode to recording or playback. Operate the mode dial to change the mode to Align with the status indicator Motion Picture Recording Mode Still Picture Recording Mode Playback Mode How to use the touch Using with the remote screen control You can operate by directly touching the...
6 Service Mode 1. Indication method of the service menu Set the mode dial “Motion Picture Recording” mode. 2. Turn the power on, and then while keep pressing the "Zoom lever" to W side, "Intelligent auto/Manual" button and "Menu" but- ton for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
6.1. Drive Information Display Touch the [ 2 ] of LCD, select Drive Information display. Operation specifications Indication contents • Drive Information display Display the fall detection frequency of HDD, Frequency that exceeds highest/lowest operation guarantee temperature and serial number. Push the menu button to end the service mode, and then POWER OFF.
6.3. Lock Search History Indication Touch the [ 4 ] of LCD, select Lock search history indication. Operation specifications Indication contents • Lock search history indication Display the camera system error cord for three histories saved in EEPROM. • The error cord contents which are displayed Error code Function Focus control is abnormal...
6.5. HDD Hardware Test Touch the [ 6 ] of LCD, select HDD hardware test. Operation specifications Indication contents • HDD hardware test Display the HDD hardware test result information. • The error cord contents which are displayed Error code Function NO ERROR It is normal without the error...
7 Service Fixture & Tools 7.1. When Replacing the Main P.C.B. After replacing the MAIN P.C.B., be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in “TSN system”, together with Maintenance software. 7.2.
Page 26
CAUTION-1. (When servicing FLASH P.C.B.) 1. Be sure to discharge the capacitor on FLASH P.C.B.. Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH P.C.B.”. The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2.
8 Disassembly and Assembly Instructions 8.1. Disassembly Flow Chart This is a disassembling chart. When assembling, perform this chart conversely. 8.2. PCB Location...
8.3. Disassembly Procedure Item Removal Side (R) OP P.C.B. Fig.D15 2 Screws (T) Item Removal Unit SP Angle Side Case (L) Unit Fig.D1 2 Screws (A) Speaker PS6501 (Connector) 4 Screws (B) P6501 (Connector) 2 Locking tabs Speaker Sensor Cover Unit Side (R) OP P.C.B.
Page 29
Item Removal Top Operation Unit Fig.D32 4 Screws (f) FP4803 (Flex) 2 Ribs Top Operation Unit MIC AMP P.C.B. Unit Fig.D33 FP4801 (Flex) FP4804 (Flex) 2 Hooks MIC AMP P.C.B. Unit Camera Operation Unit Fig.D34 2 Locking tabs Camera Operation Unit ECM FPC Unit Fig.D35 4 Locking tabs...
Page 30
8.3.2. Removal of the HDD Fig.D2 Fig.D3...
Page 31
8.3.3. Removal of the HDD Gnd Case Unit Fig.D4 8.3.4. Removal of the Top Case Unit Fig.D6 Fig.D5...
Page 32
8.3.5. Removal of the Front Unit 8.3.6. Removal of the Side Case (R) Unit Fig.D8 Fig.D7...
Page 33
8.3.7. Removal of the Batt Case Unit Fig.D11 Fig.D9 8.3.9. Removal of the Main P.C.B. Unit 8.3.8. Removal of the Lens Unit Fig.D12 Fig.D10...
Page 34
8.3.11. Removal of the Side (R) OP P.C.B. Unit and Speaker Fig.D13 8.3.10. Removal of the Flash P.C.B. Unit Fig.D15 Fig.D14...
Page 35
8.3.13. Removal of the LCD Case Unit Fig.D16 8.3.12. Removal of the Fan Motor Fig.D17 Fig.D18...
Page 36
8.3.14. Removal of the Monitor P.C.B. Unit Fig.D20 Fig.D19...
Page 37
8.3.15. Removal of the Front P.C.B. Unit Fig.D22 8.3.16. Removal of the Barrier Motor Unit Fig.D23 Fig.D21...
Page 38
Fig.D24 8.3.17. Removal of the Front Case Fig.D26 Fig.D25...
Page 39
8.3.18. Removal of the MF SENS P.C.B. Unit, Front Case Unit, MF Front Frame and MF Sheet Fig.D28 Fig.D27...
Page 40
8.3.19. Removal of the EVF Unit Fig.D29 8.3.20. Removal of the Shoe Angle, Top Frame and Shoe Cover Fig.D31 Fig.D30...
Page 41
8.3.21. Removal of the Top Operation Unit 8.3.23. Removal of the Camera Operation Unit Fig.D34 8.3.24. Removal of the ECM FPC Unit Fig.D32 8.3.22. Removal of the MIC AMP P.C.B. Unit Fig.D33 Fig.D35...
Page 42
8.3.26. Removal of the MOS Heat Radiation Plate Fig.D36 8.3.25. Removal of the Batt Catcher P.C.B. Fig.D38 Unit 8.3.27. Removal of the Prism Unit and Optical Filter Fig.D39 Fig.D37...
Page 43
8.3.28. Removal of the IRIS Unit 8.3.29. Removal of the Zoom Motor Fig.D41 Fig.D40...
Page 44
8.3.30. Removal of the 1st Lens Frame Unit 8.3.32. Removal of the Body Unit and the Zoom Guide Pole Fig.D42 8.3.31. Removal of the 2nd Lens Frame Move Unit Fig.D44 Fig.D43...
Page 45
8.3.33. Removal of the Master Flange Cover Fig.D45 8.3.34. Removal of the 4th Lens Frame Move Unit Fig.D46 Fig.D47...
Page 46
8.3.35. Removal of the Focus Guide Pole L and Focus Guide Pole S Fig.D48...
9 Measurements and Adjustments 9.1. Electric Adjustment • Adjustment method is different from a conventional High definition video camera. • An exclusive jig and PC (including software for adjustment “Tatsujin”) are necessary for electric adjustment. • A USB driver for service is necessary to communication with PC. •...
Page 48
Adjustment Items • Adjustment item as follows. The adjustment instruction is available at "Software download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN System".
10 Factory Setting 10.1. How To Turn On The Factory Settings? 1. Set the mode switch “Motion Picture Recording” mode. 2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Intelligent auto/Manual” button and “Menu” but- ton for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
10.2. What Is The Factory Settings? The factory settings clean up and/or refresh the following settings. 1. MENU, MODE, ADJUSTMENT VALUE. 2. SD card format. 3. Reset the folder number and file number of still pictures. (Setting the folder number is 100, and file number is 0.) 4.
Page 51
3.The voltage being indicated on the schematic diagram is measured in "Standard-Playback" mode when there is no specify mode is mentioned. Model No. HDC-HS700P HDC-HS700EF 4.Although the voltage and waveform available on here is measured with standard frame, it may be differ from actual measurement due to modification of circuit and so on.
S2. Voltage Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
S3. Block Diagram S3.1. Overall Block Diagram : VIDEO SIGNAL NOTE : AUDIO SIGNAL : CLK or CONTROL LINE LENS(F1.5-2.8 12x) ZOOM/ IC151 FOCUS IRIS/ MOS IMAGE MOTOR/ SENSOR x 3 IC851 COLOR EVF EVF COLOR PANEL DRIVER Analog COLOR LCD PANEL X301 (42.725275MHz)
S4.10. CAM FUNC FPC Schematic Diagram / S4.11. Side R Schematic Diagram TO SPEAKER P6501 K1KA02BA0014 SPOUT2 SPOUT1 S6601 TO MIC_AMP_PCB FP4804 K1MY04BA0370 TO BATT_CATCHER K0F111A00589 FT6501 FP6501 [0.5mm] K1MN08A00072 TO FAN VTR_KEY_5 VTR_KEY_5 SPOUT1 PS6501 CAMERA FUNCTION K1KA03BA0014 SPOUT2 PW_FAN5V PW_FAN5V FAN_FG...
S6. Replacement Parts List 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE of this assembly in production, it will no longer be available. E.S.D. standards for Electrostatically Sensitive Devices, refer to “PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES”...
Page 74
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks R3908 ERJ2GEJ103 M.RESISTOR CH 1/10W ■ VEP03H98AN MAIN PCB UNIT 1 P,PC,PU,GT (RTL) E.S.D. R3909 ERJ2GEJ102X M.RESISTOR CH 1/16W ■ VEP03H98AQ MAIN PCB UNIT 1 EE,GC,GN (RTL) E.S.D.
Page 75
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks R4910 ERJ2GEJ562 M.RESISTOR CH 1/10W 5.6K R4911 ERJ2GEJ151 M.RESISTOR CH 1/10W IC4801 C0ABBB000369 IC 1 E.S.D. R4912 ERJ2GEJ471 M.RESISTOR CH 1/10W IC4802 C0ABBB000369 IC 1 E.S.D.
Page 76
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks JK6751 K4ZZ04000049 JACK, BATTERY CATCH ■ VEP06G50A SIDE R OP PCB UNIT (RTL) E.S.D. PP601 K1KB50AA0094 CONNECTOR FP6501 K1MN08A00072 CONNECTOR R851 ERJ2GEJ102X M.RESISTOR CH 1/16W R852 ERJ2RHD511...
Page 77
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks XQS2+A35FN SCREW VEP79258A HDD FPC UNIT 1 (RTL) E.S.D. VGK3616 MF RING VYK3Q71 BARIA CASE UNIT VGL1326 TARY PANEL LIGHT VGL1309 AF PANEL LIGHT N9ZZ00000415 BARRIER MOTOR UNIT EFN-MVBH7ZC FLASH...
Page 78
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks VEP03H98AN MAIN PCB UNIT 1 P,PC,PU,GT (RTL) E.S.D. VEP03H98AQ MAIN PCB UNIT 1 EE,GC,GN (RTL) E.S.D. VEP03H98AP MAIN PCB UNIT 1 EG,EP,EF,EB,EC (RTL) E.S.D. VWJ2133 FRONT FPC VWJ2132...
Page 79
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks VGQ0K38 EYE CUP VGQ0D06 EVF LENS CASE VDL2175 EVF LENS (A) VGQ0C99 LENS HOLDER (A) VDL2176 EVF LENS (B) VGQ0D00 LENS HOLDER (B) VGQ0K39 EVF CASE VGU0E13...
Page 80
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks VEP26330A MONITOR PCB UNIT 1 (RTL) E.S.D. VYK3Q66 LCD CASE (T) UNIT VYK3U03 PANEL UNIT VGQ0K48 LIGHTING PLATE HOLDER VGL1322 PRISM SHEET A VGL1323 PRISM SHEET B VGL1324...
Page 81
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks VXQ1862 PRISM UNIT VXW1115 LENS UNIT L6HA88NC0006 STEPPING MOTORS VXP3372 IRIS UNIT VMA0X14 SIDE YORK VMA0X14 SIDE YORK VMS8060 ZOOM GUIDE POLE VMS8060 ZOOM GUIDE POLE VMS8061...
Page 82
HDC-HS700 vol.1 Ref.No. Part No. Part Name & DescriptionPcs Remarks Ref.No. Part No. Part Name & DescriptionPcs Remarks K2GJYDC00004 DC CABLE K1HY12YY0004 MULTI D/RCA CABLE K1HY04YY0032 USB CABLE N2QAEC000024 REMOTE CONTROL UNIT 306 DE-A51CB AC ADAPTOR 1 EG,EP,EF,EB,EC,EE,PU,GC, GT,GN ...