Bush Hog 1145 Operator's Manual
  1. Manuals
  2. Brands
  3. Bush Hog Manuals
  4. Compact Loader
  5. 1145
  6. Operator's manual
Bush Hog 1145 Operator's Manual

Bush Hog 1145 Operator's Manual

Bush hog compact loader user manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Published 01/11
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
®
BUSH HOG
2501 Griffin Ave.
Selma, AL 36703
334-874-2700
www.bushhog.com
OPERATOR'S MANUAL
© 2011 Alamo Group Inc.
1145
LOADER
50069159
Part No.
$0.00

Advertisement

Table of Contents
loading

Related Manuals for Bush Hog 1145

Summary of Contents for Bush Hog 1145

  • Page 1 This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01- Cover ® BUSH HOG 2501 Griffin Ave. Selma, AL 36703 334-874-2700 www.bushhog.com ©...
  • Page 2 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS SAFETY SECTION ... 1-1 General Safety Instructions and Practices ... 1-2 Operator Safety Instructions and Practices ... 1-4 Equipment Operation Safety Instructions and Practices ... 1-5 Connecting or Disconnecting Implement Safety Instructions and Practices ... 1-10 Transporting Safety Instructions and Practices ... 1-11 Maintenance and Service Safety Instructions and Practices ...
  • Page 4 MAINTENANCE SECTION ... 5-1 Lubrication Schedule ... 5-4 Daily Maintenance ... 5-5 Adjusting Bucket Lever Indicator ... 5-5 Cylinder Service ... 5-6 Lift and Bucket Cylinder Disassembly ... 5-6 Lift and Bucket Cylinder Reassembly ... 5-7 Storage ... 5-8 Proper Torque for Fasteners ... 5-10...

  • Page 5: Safety Section

    SAFETY SECTION Safety Section 1-1...

  • Page 6: General Safety Instructions And Practices

    (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS. 1145 01/11 © 2011 Alamo Group Inc. SAFETY (SG-3)
  • Page 7 Push and pull the control levers in and out several times to remove pressure. Do not work under raised Boom or Bucket unless components are securely blocked up to prevent inadvertent dropping. 1145 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 8: Operator Safety Instructions And Practices

    Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. 1145 01/11 © 2011 Alamo Group Inc. SAFETY Never allow inexperienced or untrained personnel to...

  • Page 9: Equipment Operation Safety Instructions And Practices

    Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, serious injury, or even death. Never allow the Implement to contact obstacles. Never grasp control levers when mounting the machine. 1145 01/11 © 2011 Alamo Group Inc. SAFETY (SG-32)
  • Page 10 Attacking insects can cause you to lose control of the tractor, which can result in serious injury or death to you or bystanders. Never dismount a moving tractor. (SG-40) 1145 01/11 © 2011 Alamo Group Inc. SAFETY (SBH-9)
  • Page 11 Walking into the point of the bale or grapple spear can cause serious bodily injury. Never drive the bale spear or grapple bucket attachment forward if a bystander is in front of the loader. (SL-10) 1145 01/11 Safety Section 1-7 © 2011 Alamo Group Inc.
  • Page 12 Do not use loader as a jack to raise the tractor tires off the ground. The loader could fail causing the tractor and loader to fall to the ground resulting in serious injury. 1145 01/11 © 2011 Alamo Group Inc.
  • Page 13 Implement. Lower the implement carefully to the ground. Do not put hands or feet under lifted components. 1145 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 14: Connecting Or Disconnecting Implement Safety Instructions And Practices

    Never allow anyone to get under the loader or attachment or to reach through the loader lift arms when raised. Serious injury could result from crushing or pinching by the loader or attachment. 1145 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 15: Transporting Safety Instructions And Practices

    When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy. 1145 01/11 © 2011 Alamo Group Inc. SAFETY...
  • Page 16 Never drive the power unit with the bucket or plow in the raised position. Traveling with the bucket or plow in the raised position increases the chances of colliding with overhead obstructions and making the unit more prone to tipping over. 1145 01/11 © 2011 Alamo Group Inc. SAFETY (SL-21)

  • Page 17: Maintenance And Service Safety Instructions And Practices

    If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure. Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. 1145 01/11 © 2011 Alamo Group Inc. SAFETY (SG-6)
  • Page 18 These parts are made and tested to Bush Hog specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and safety.

  • Page 19: Storage And Parking Safety Instructions And Practices

    Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment. 1145 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 20: Decal Location

    Decal Location NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply).
  • Page 21 D468 D471 D470 03200347 00776031 * - Supplied by Tractor Manufacturer. Replace if missing from Tractor. NOTE: Order D438 Safety Decal Sheet which includes all safety decals. 1145 01/11 © 2011 Alamo Group Inc. SAFETY LEVEL DESCRIPTION LOGO Bush Hog...

  • Page 22: Decal Description

    Decal Description Logo: BUSH HOG (3.20” x 14.50”) P/N 50057411 MODEL NAME: 1145 P/N 50069070 WARNING! - DO NOT operate with oil leaks. -Inspect hoses regularly. Failure to inspect and replace worn hoses may allow them to rupture suddenly and violently, resulting in serious bodily injury or death from scalding, fire burn injury, or oil penetration.
  • Page 23 -Do not remove bucket or attachment form detached loader. -Do not allow riders on tractor or loader. -Do not allow children or untrained persons to operate loader. D469 1145 01/11 © 2011 Alamo Group Inc. SAFETY Safety Section 1-19...
  • Page 24 Failure to comply may result in serious injury or death. D470 Slow Moving Vehicle Decal. Keep SMV reflector clean and visible. DO NOT transport or operate without the SMV. P/N 03200347 1145 01/11 © 2011 Alamo Group Inc. SAFETY Safety Section 1-20...
  • Page 25 SAFETY Read Operator’s Manual! The operator’s manual is located inside this canister. If the manual is missing order one from your dealer. P/N 00776031 1145 01/11 Safety Section 1-21 © 2011 Alamo Group Inc.

  • Page 26: Federal Laws And Regulations

    Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) 1145 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 27: Introduction Section

    INTRODUCTION SECTION Introduction Section 2-1...
  • Page 28 This 1145 Loader is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Front End Loader using standard and optional equipment.
  • Page 29 (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS. 1145 01/11 © 2011 Alamo Group Inc. INTRODUCTION (SG-30)
  • Page 30 INTRODUCTION The Bush Hog 1145 Loader is designed for four-wheel drive tractors. They are intended to lift only loose materials that will fit in the bucket. All cylinders are double-acting. Parking stands support loader so tractor can be “driven in” for quick attaching.
  • Page 31 Alamo Group within thirty days of delivery of the implement. 3. Record the Loader Model and Serial Numbers on the Warranty page. Keep this as part of the permanent maintenance file for the implement. 1145 01/11 Introduction Section 2-5 © 2011 Alamo Group Inc.

  • Page 33: Assembly And Connecting The Loader Section

    ASSEMBLY AND CONNECTING THE LOADER SECTION Assembly Section 3-1...

  • Page 34: Assembly Instructions

    Sudden or unexpected movement or dropping of the loader and attachment could result in serious injury. 1145 01/11 © 2011 Alamo Group Inc. ASSEMBLY...

  • Page 35: Proper Ballasting And Wheel Spacing

    Spread front wheels to maximum distance. Spread rear wheels to maximum distance. Add rear wheel weight, rear ballast box or implement. Make sure there is 20% of total weight on rear axle. 1145 01/11 Assembly Section 3-3 © 2011 Alamo Group Inc.

  • Page 36: Dismounting Loader And Mounting Loader To Tractor

    5. Set parking brake. Rotate parking stands from storage position by removing linch pins and clevis pins. Reinstall clevis pins and linch pins when parking stands are in operation position (See Figure Asm-L-0024). 1145 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-4...
  • Page 37 Relax lift cylinders and bucket cylinders by moving each control lever in both directions. Disconnect hydraulic hoses from tractor. 11. Start tractor engine and release brakes. Slowly back tractor out of loader. 1145 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-5...

  • Page 38: Mounting Loader

    (See Figure Asm-L-0024). Note: If front wheel spacings were changed while loader was off tractor, tire clearances must be checked and possibly adjusted to ensure proper clearances. 1145 01/11 © 2011 Alamo Group Inc. ASSEMBLY...

  • Page 39: Attaching Pin On Bucket

    3. Set bucket level on ground and adjust level guide tube along bucket cylinder until end of guide tube is flush with end or rod. 1145 01/11 © 2011 Alamo Group Inc. ASSEMBLY...

  • Page 41: Operation Section

    OPERATION SECTION Operation Section 4-1...
  • Page 42 Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a 1145 loader and are not necessarily of a 1145 loader or exact tractor. Some pictures may show shields removed for purposes of clarity.

  • Page 43: Standard Equipment And Specifications

    Reach with Bucket on Ground Bucket Rollback Angle Digging Depth Overall Height in Carry Position (Manufacturers estimated specifications and design subject to change without notice.) 1145 01/11 © 2011 Alamo Group Inc. OPERATION 20-30 HP 2000 PSI/ 8 GPM 1035 lbs.

  • Page 44: Operator Requirements

    NOTE: Hearing loss from loud noise [from tractors, chain saws, radios, and other such sources close to the ear] is cumulative over a lifetime without hope of natural recovery. 1145 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 45 If you are using a tractor equipped with a cab, make sure the cab is rated for appropriate environmental exposure. Be safe and always wear proper protection. Short or long term exposure to certain chemicals and materials can result in serious injury or death. 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-22)
  • Page 46 Protective Eye Glasses, Goggles, or Face Shield • Hard Hat • Steel Toe Safety Footwear • Gloves • Hearing Protection • Close Fitting Clothing • Respirator Filter Mask operating conditions) OPS-L- 0021 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-41) (depends Operation Section 4-6...

  • Page 47: Tractor Requirements

    Most tractor’s have different settings for operating and transporting lighting. Refer to the tractor operator’s manual for using the tractor’s light switch and operating the turn signals. OPS-B- 0017 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-7) Operation Section 4-7...

  • Page 48: Tractor Ballast

    Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-L- 0022 1145 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 49: Boarding The Tractor

    Use hand rails and steps when exiting the tractor. Be careful of your step and use extra caution when mud, ice, snow or other matter has accumulated on the steps or hand rails. Use all handrails and steps for support and never rush or jump off the tractor. OPS-L- 0024 1145 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 50: Starting The Tractor

    Never bypass the ignition switch by short circuiting the starter solenoid. After the tractor engine is running, avoid accidental contact with the tractor transmission to prevent sudden and unexpected tractor movement. OPS-L-0025 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-23)

  • Page 51: Pre-Operation Inspection And Service

    Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death. (SL-36) 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-21) Operation Section 4-11...

  • Page 52: Tractor Pre-Operation Inspection/Service

    Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding. 1145 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 53 • Ensure all pins are in place and fastened with screws. • Ensure frame is properly mounted to tractor hardware properly tightened. OPS-L-0004_C 1145 01/11 © 2011 Alamo Group Inc. OPERATION installed Operation Section 4-13 (SG-15) Mount Frame Assembly...
  • Page 54 • Inspect the condition of the bucket lug weldments. • Inspect condition of bushings. OPS-L-0007_B 1145 01/11 © 2011 Alamo Group Inc. OPERATION along hoses, Operation Section 4-14 Hydraulic Hoses Bucket Pins...
  • Page 55 The engine coolant fluid level is full The radiator is free of debris The air filter is in good condition Operator’s Signature:___________________________________________________ DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT 1145 01/11 © 2011 Alamo Group Inc. OPERATION Condition at Start of Shift...
  • Page 56 The Control Valve Lock functions correctly The Pivot Pins are properly lubricated The Loader Storage Stands are in good condition Operator’s Signature: DO NOT OPERATE an UNSAFE TRACTOR or FRONT END LOADER 1145 01/11 © 2011 Alamo Group Inc. OPERATION Condition at Start of Shift...

  • Page 57: Driving The Tractor And Loader

    Failure to maintain adequate vision of the public roadway and traffic can result in serious injury or even death. (STI-10) 1145 01/11 © 2011 Alamo Group Inc. OPERATION (S3PT-12)

  • Page 58: Operating The Tractor And Loader

    Use extreme care when piling material above 6 feet high. Material could shift and fall onto the operator or bystanders. The material could crush or suffocate the operator or bystander resulting in serious injury or death. (SL-17) 1145 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-18...
  • Page 59 Keep bystanders 10 feet away from the tractor and loader while operating. The bystanders could enter the path of the tractor or items could fall from the loader resulting in serious injury to the bystander. 1145 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 60 Use extreme care when piling material above 6 feet high. Material could shift and fall onto the operator or bystanders. The material could crush or suffocate the operator or bystander resulting in serious injury or death. (SL-17) 1145 01/11 Operation Section 4-20 © 2011 Alamo Group Inc.
  • Page 61 If you are unable to clearly see these types of items discontinue operating. Contact with unseen vehicles, bystanders, obstructions, or drop-offs can cause serious injury. 1145 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 62 Always have a heavy attachment, such as a bucket mounted on loader when it is removed from tractor. It is important not to put excessive weight on parking stands with lift cylinder retraction. Damage may result. 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SPU-3)

  • Page 63: Operating The Loader

    Loaders with 1-lever control, ease lever back toward you to lift and roll back bucket. With series valve, prevent loader stall by not lifting and rolling back at the same time. 1145 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-23...
  • Page 64 Time is lost if two or more attempts are made to fill the bucket on each pass. 1145 01/11 Operation Section 4-24 © 2011 Alamo Group Inc.
  • Page 65 Attachment can be adjusted by using bucket cylinders. CARRYING THE LOAD Position bucket just below tractor hood for maximum stability and visibility, whether bucket is loaded or empty. 1145 01/11 Operation Section 4-25 © 2011 Alamo Group Inc.
  • Page 66 DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle. Move tractor in as close as possible to side of vehicle, then dump bucket. 1145 01/11 Operation Section 4-26 © 2011 Alamo Group Inc.
  • Page 67 OPERATION LOWERING THE BUCKET After bucket is dumped, back away from vehicle while lowering and rolling back bucket. 1145 01/11 Operation Section 4-27 © 2011 Alamo Group Inc.
  • Page 68 Float will also prevent mixing of surface material with stockpile material. Float position will reduce the chance of surface gouging when removing snow or other material. 1145 01/11 Operation Section 4-28 © 2011 Alamo Group Inc.
  • Page 69 If the pile sides are too high and liable to cause cave-in, use loader to break down the sides until a slot can be cut over the top. 1145 01/11 Operation Section 4-29 © 2011 Alamo Group Inc.
  • Page 70 Another method for large dirt piles is to build a ramp approach to the pile. It is important to keep the bucket level when approaching a bank or pile. This will help prevent gouging the work area. 1145 01/11 Operation Section 4-30 © 2011 Alamo Group Inc.
  • Page 71 Make additional passes until desired depth is reached. During each pass, use only bucket control while working depth. This will allow you to concentrate on controlling bucket angle to maintain a precise cut. 1145 01/11 Operation Section 4-31 © 2011 Alamo Group Inc.
  • Page 72 Do not roll bucket over and attempt to backgrade. This type of use can cause severe overloading of bucket cylinders when fully extended, possibly causing bucket cylinder rods to become bent. 1145 01/11 Operation Section 4-32 © 2011 Alamo Group Inc.
  • Page 73 Do not use bucket in dumped position for bulldozing. This method, shown above, will impose severe shock loadings on dump linkage, bucket cylinder and tractor. 1145 01/11 Operation Section 4-33 © 2011 Alamo Group Inc.
  • Page 74 OPERATION Leave dirt in bucket. Dumping on each pass wastes time. Operate tractor at right angles to ditch. Take as big a bite as tractor can handle without lugging down. 1145 01/11 Operation Section 4-34 © 2011 Alamo Group Inc.
  • Page 75 Never lifting large objects with equipment that does not have an anti-rollback device. • Moving slowly and carefully, avoiding rough terrain. • Tilt bucket forward while lifting to maintain bucket angle. 1145 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-35...

  • Page 76: Operating Bale Spear (Optional Attachment)

    Load bale spear by approaching from round end to prevent cutting strings or puncturing plastic or net wrap.Tilt bale spear upward to prevent bale from falling off of spear, 1145 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-36...

  • Page 77: Shutting Down The Implement

    Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the loader. 10. Transporting the Tractor and Implement Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. 1145 01/11 © 2011 Alamo Group Inc. OPERATION (SG-10)
  • Page 78 Before dismounting the tractor and loader, lower the loader to the ground or onto solid support blocks. Sudden dropping of the loader and attachment could result in serious injury. (SL-38) 1145 01/11 © 2011 Alamo Group Inc. OPERATION Determine the maximum...

  • Page 79: Transporting On Public Roadways

    Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. 1145 01/11 © 2011 Alamo Group Inc. OPERATION Locking the...
  • Page 80 Do not exceed the legal speed limit set in your country for agricultural tractors. Always stay alert when transporting the tractor and implement on public roads. Use caution and reduce speed if other vehicles or pedestrians are in the area. OPS-L- 0020 1145 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 81: Hauling The Tractor And Implement

    OPS-U- 0025 1145 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-41...

  • Page 82: Troubleshooting Guide

    TROUBLE Loader slow or will not lift and/or dump Loader chatters or vibrates when raising or lowering. Oil Leaks 1145 01/11 © 2011 Alamo Group Inc. OPERATION POSSIBLE CAUSE Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking.
  • Page 83 PROBLEM Insufficient lift capacity Excessive wear on bucket cutting edge Bucket cutting edge not flat on theground. 1145 01/11 © 2011 Alamo Group Inc. OPERATION POSSIBLE CAUSE Load is greater than boom lift capacity. Improper hydraulic pump operation. Internal lift cylinder leakage.

  • Page 85: Maintenance Section

    MAINTENANCE SECTION Maintenance Section 5-1...
  • Page 86 If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure. Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. 1145 01/11 © 2011 Alamo Group Inc. MAINTENANCE (SG-6)
  • Page 87 These parts are made and tested to Bush Hog specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and safety.

  • Page 88: Lubrication Schedule

    Lubricate all grease fittings: one at each end of lift boom arms and one at rod and base ends of each lift and bucket cylinders. NOTE: Fully retract bucket to a comfortable height to grease bucket/loader boom joint. Do not reach or stand under a raised loader or attachment without proper support. 1145 01/11 Maintenance Section 5-4 © 2011 Alamo Group Inc.

  • Page 89: Daily Maintenance

    Loosen tightener band and adjust level guide tube along bucket cylinder until end of guide tube is flush with end of rod. Tighten band. 1145 01/11 © 2011 Alamo Group Inc. MAINTENANCE Maintenance Section 5-5...

  • Page 90: Cylinder Service

    6. Clean all parts including cylinder tube, in a suitable cleaning solvent, then use air pressure to blow any dirt or excess solvent from all parts. 7. Examine all parts for wear or damage and replace, if necessary. 1145 01/11 © 2011 Alamo Group Inc. MAINTENANCE...

  • Page 91: Lift And Bucket Cylinder Reassembly

    Note: If cylinder has a countersunk hole, hook end of retaining wire into hole and turn cylinder head 1-1/2 turns to secure wire. End of hook may need to be ground to fit in countersunk hole. 1145 01/11 © 2011 Alamo Group Inc.

  • Page 92: Storage

    Failure to do so will result in tractor hydraulic pump damage. 1. Store loader with attachment attached. 2. Place dust caps on hydraulic quick couplers. 1145 01/11 © 2011 Alamo Group Inc. MAINTENANCE (SL-26) (SL-27) securely Maintenance Section 5-8 (SL-13)
  • Page 93 MAINTENANCE 3. Do not remove attachment from stored loader. 4. Do not allow children to play on or around loader. 1145 01/11 Maintenance Section 5-9 © 2011 Alamo Group Inc.

  • Page 94: Proper Torque For Fasteners

    NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine oil. They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are used. This applies to both UNF fine and UNC coarse threads. 1145 01/11 Maintenance Section 5-10 © 2011 Alamo Group Inc.
  • Page 95 MAINTENANCE 1145 01/11 Maintenance Section 5-11 © 2011 Alamo Group Inc.
  • Page 96 MAINTENANCE 1145 01/11 Maintenance Section 5-12 © 2011 Alamo Group Inc.

  • Page 98: Limited Warranty

    2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability.
  • Page 99 To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT requirements of tractor operators: REQUIRED OF THE OWNER:...
  • Page 100 1145 LOADER 1145-SOM-01/11 P/N 50069159 Printed U.S.A...

Table of Contents