Table of Contents
Advertisement
Quick Links
INSTALLATION AND OPERATING INSTRUCTIONS
POSITIVE PRESSURE GAS FIREPLACE
MODEL : SE36 – NG Natural Gas
SE36 – LP Propane
These gas appliances have been tested in accordance
with National Safety Standards, and have been certified
by Intertek for installation & operation as described in
these Installation and Operating Instructions in the
United States.
Check with your local building code agency before you
begin your installation to ensure compliance with local
codes, including the need for "permits" and follow-up
inspections. If any problems are encountered regarding
code approvals, or if you need clarification of any of the
instructions contained here, contact:
ALPINE GAS FIREPLACES
#801-768-8411 / www.alpinegasfireplaces.com
WARNING:
instructions are not followed exactly, a fire or
explosion
may
damage , personal injury or loss of life.
Improper installation, adjustment, alteration,
service or maintenance can cause property
damage, personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
INSTALLER:
HOMEOWNER:
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Alpine Gas Fireplaces
782 West State Street
Lehi, Utah 84043
7/04
SERRANO
If the information in these
result
causing
property
PLEASE LEAVE THIS MANUAL WITH THE CUSTOMER
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
•
Do not touch any electrical switch; do
•
not use any phone in your building.
Immediately call your gas supplier from
•
a neighbor's phone. Follow the gas
supplier's instructions
If you cannot reach your gas supplier,
•
call the fire department.
INSTALLATION AND SERVICE MUST
BE PERFORMED BY A QUALIFIED
INSTALLER, SERVICE AGENCY OR THE
GAS SUPPLIER.
Tested by:
Advertisement
Table of Contents
Related Manuals for Alpine SERRANO SE36-NG
Summary of Contents for Alpine SERRANO SE36-NG
- Page 1 “permits” and follow-up inspections. If any problems are encountered regarding code approvals, or if you need clarification of any of the instructions contained here, contact: ALPINE GAS FIREPLACES #801-768-8411 / www.alpinegasfireplaces.com WHAT TO DO IF YOU SMELL GAS: WARNING: If the information in these Do not try to light any appliance.
- Page 2 Alpine SE36 Direct Vent Gas Fireplace...
-
Page 3: Table Of Contents
Removing/Installing the Valve..31 Flex Venting………………………..20 Replacement Parts List..... 32 POSITIVE PRESSURE TROUBLESHOOTING GUIDE Installation ........21/22 Gas Control System ......33 WIRING Positive Pressure System ....34 Blower Wiring ........23 WARRANTY Millivolt System ....... 24 Warranty……………………………35 Alpine SE36 Direct Vent Gas Fireplace... -
Page 4: General Information
GENERAL INFORMATION Model SE36-LP Model SE36-NG Alpine SE36 Direct Vent Gas Fireplace... -
Page 5: Before Starting
CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE. 15) Never obstruct the flow of ventilation and combustion air to the fireplace. CLOTHING OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE. Alpine SE36 Direct Vent Gas Fireplace... -
Page 6: System Specifications
Natural Gas 3.5” +/-0.2” w.c. depth of appliance. Propane 10” +/-0.2” w.c. 5) The Alpine SE36 fireplace can be installed into Minimum Gas Line Pipe Size: 1/2” many different applications. See Figure 1 for examples. Electrical: 120 V.A.C. System 6) Lay out fireplace dimensions on installation site Amperage Rating: 3.25 /3.50 Amps... -
Page 7: Gas Line Installation
Add 1” of height for each additional 1” of projection. Horizontal Vent Pipe Top of Pipe 2” Sides of Pipe 1” Bottom of Pipe 1/2” Vertical Vent Pipe 1 1/2” Fig. 4 – Hearth Clearances Alpine SE36 Direct Vent Gas Fireplace... -
Page 8: Framing And Finishing
The fireplace is equipped with four nailing the fireplace make sure not to overlap into tabs, which must be bent out before the glass frame area. (see figure 8) inserting into the framed opening. Alpine SE36 Direct Vent Gas Fireplace... -
Page 9: Venting
09382 17” - 24” Adjustable pipe 46DVA-12 12” pipe This venting system, in combination with the Alpine SE-36 46DVA-24 24” pipe Direct Vent Gas Fireplace, has been tested and listed as a 46DVA-36 36”... -
Page 10: Vent Termination Clearances
VENTING VENT TERMINATION CLEARANCES Alpine SE36 Direct Vent Gas Fireplace... -
Page 11: Horizontal /Vertical Components
The vertical termination should project above the finished never be recessed into the wall. A brick standoff is chase a minimum of 10”. See local codes for other vent- available for this application. ing requirements in your area. Alpine SE36 Direct Vent Gas Fireplace... -
Page 12: Vertical Venting
Only Simpson Duravent GS Piping (4” x 6 5/8”) May be Used on This Appliance. Piping Clearances Vertical Pipe 1 1/2” to Combustibles Horizontal Pipe 2” To Combustibles—Top 1” To Combustibles—Sides 1/2” To Combustibles—Bottom Alpine SE36 Direct Vent Gas Fireplace... - Page 13 3 FT 3 FT 2 FT 5 FT 5 FT 5 FT 3 FT 3 FT 10 FT 5 FT 10 FT 3 FT NOTE: Horizontal Piping Must Maintain a 1/4” Rise Per Foot. Alpine SE36 Direct Vent Gas Fireplace...
- Page 14 VENTING Alpine SE36 Direct Vent Gas Fireplace...
-
Page 15: Horizontal Venting
NOTE: Horizontal Piping Must Maintain A 1/4” Rise Per Foot. Note: V1 must be at least a 1 foot length. Piping Clearances Vertical Pipe 1 1/2” to Combustibles Horizontal Pipe 2” To Combustibles—Top 1” To Combustibles—Sides 1/2” To Combustibles—Bottom Alpine SE36 Direct Vent Gas Fireplace... - Page 16 10 FT 5 FT 12 FT NOTE: Horizontal Piping Must Maintain A 1/4” Rise Per Foot. Piping Clearances Vertical Pipe 1 1/2” to Combustibles Horizontal Pipe 2” To Combustibles—Top 1” To Combustibles—Sides 1/2” To Combustibles—Bottom Alpine SE36 Direct Vent Gas Fireplace...
-
Page 17: Horizontal Installation
13). Carefully fasten the termination cap to the exterior tape or Silicone on the outer joint. wall (see fig. 14) using the screws provided in the termination box. You may seal around the termination cap with a quality silicone for insulation purposes. Alpine SE36 Direct Vent Gas Fireplace... -
Page 18: Vertical Installation
Mill-pac brand sealant on the inside collar and aluminum tape on the exterior. An air tight must be created. Fig.14– Anchoring Termination to Wall Alpine SE36 Direct Vent Gas Fireplace... - Page 19 The vent must never be allowed to come in contact with 8. Install the vent cap by twist locking it in place. combustibles Alpine SE36 Direct Vent Gas Fireplace...
-
Page 20: Flex Venting
Horizontal Venting With One 90 Degree Elbow Vertical Horizontal 1 FT 2 FT 2 FT 3 FT 2" 3-8 FT 3 FT NOTE: Horizontal piping must maintain 1/4” rise per foot. 24" 12" INCORRECT CORRECT Alpine SE36 Direct Vent Gas Fireplace... -
Page 21: Installation
POSITIVE PRESSURE SYSTEM POSITIVE PRESSURE SYSTEM The Alpine SE-36 is equipped with a highly efficient 1 4 " x 1 4 " x 1 4 " positive pressure heating system. This system provides F lu s h F a n outside air for heating. -
Page 22: Positive Pressure
Grill Assembly Extended Fan Fig. 14– Extended Blower Installation Assembly Extended Fan Assembly Fig.26 – Possible Blower Locations NOTE: When installing the positive pressure system, always follow local mechanical codes. Fig. 15– Extended Blower Alpine SE36 Direct Vent Gas Fireplace... -
Page 23: Wiring
Some prefer the switch be co-located with the positive pressure blower controller. If this choice is made, a DIVIDED double gang electrical box must be installed. (A standard (non-divided) double gang box cannot be used.) Fig. 29– Controller Wiring Alpine SE36 Direct Vent Gas Fireplace... -
Page 24: Millivolt System
Carefully remove logs from their packaging . You will power attached to them. If power is attached to the control notice that your Alpine Gas Fireplace logs are extremely valve, damage will certainly occur. lightweight and are very fragile, care must be taken when handling. -
Page 25: Ember Placement
(fig.34) Locate the top left twig (36-8) and place it on the left side log (36-2) and left bottom twig (36-4) onto the pads pro- vided. (see fig. 37) Alpine SE36 Direct Vent Gas Fireplace... -
Page 26: Glass And Louver Installation
/ cleaner flame, or by closing the air shutter for a more yellow flame. See (figures 42 and 43) for proper flame characteristics, and primary air adjustment. Fig. 40 – Installing The Bottom Louver Alpine SE36 Direct Vent Gas Fireplace... -
Page 27: Remote Control/Thermostat
AERATION ADJUSTMENT/REMOTE CONTROL & THERMOSTAT REMOTE CONTROL (Optional) An Alpine Remote Control Kit (08501) may be installed on this fireplace. The remote control kit comes with a hand held transmitter, a receiver, a wall mounting plate, and a wall mounted transmitter cradle. The remote control is... -
Page 28: Operation Instruction Plate
2) Turn off all electric power to the appliance 1) Push in the gas control knob slightly and if service is to be performed. turn clockwise to “OFF”. Do not force. LX-999-1 DO NOT REMOVE THIS INSTRUCTION PLATE Alpine SE36 Direct Vent Gas Fireplace... -
Page 29: First Fire
DO NOT use cleaners of any type on the stainless or gold. Be sure to clean any fingerprints off of the unit BEFORE turning the fireplace on. Alpine SE36 Direct Vent Gas Fireplace... -
Page 30: Glass Panel/Replacement
In the event that you break your glass by impact, purchase 5) Remove the two 1/4” screws holding the pilot assembly your replacement from an authorized Alpine dealer. See in its bracket. Gently lift the pilot assembly up 2”. the replacement parts list for ordering information. Follow 6) Disconnect the thermopile and thermocouple with a the replacement steps below. -
Page 31: Removing/Installing The Valve
13)Make sure the toggle switch is in the solution to check for leaks. “OFF” Position 14)Ignite pilot and check for leaks in pilot line 15)Ignite main burner and check for leaks in main burner tube. Alpine SE36 Direct Vent Gas Fireplace... -
Page 32: Replacement Parts List
Burner – Nat Gas / Prop 04046 Piezo Igniter 04080 Door Extension Spring 08210 Blower Assembly 04038 Pilot Assembly –N.G. 05082 Pilot Orifice L.P. 06095 Bottom Door Hinge 08501 Remote Control 24500 Top Door 24502 Bottom Door Alpine SE36 Direct Vent Gas Fireplace... -
Page 33: Troubleshooting Guide Gas Control System
Thermopile or thermocouple against the appliance or gas valve. may be grounding out. Caution: Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance Alpine SE36 Direct Vent Gas Fireplace... -
Page 34: Positive Pressure System
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Always verify operation after servicing Caution: Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance Alpine SE36 Direct Vent Gas Fireplace... -
Page 35: Warranty
The damaged part or parts of the firebox will be repaired or replaced at Alpine's option. Parts which are returned to Alpine and are found damaged by burnout on inspection will be repaired, or replaced with a new part, without charge to the purchaser as long as the unit is still under warranty.