Sealey LED130110P.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances before use, to ensure that they are safe. You must inspect power supply
leads, plugs and all electrical connections for wear and damage. You must also read and understand the following instructions
concerning electrical safety.
the Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
1.1.1
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2 the Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3 Ensure the insulation on all cables and the product itself is safe before connecting to
the power supply. see 1.1.1 & 1.1.2 above and use a Portable Appliance tester (PAt).
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply, leads, plugs and all electrical connections for wear
and damage, and power connections to ensure that none is loose.
1.1.6 Important: Ensure the voltage marked on the product is the same as the electrical
power supply to be used.
1.1.7 DO NOT pull or carry the appliance by the power supply or output cables.
1.1.8 DO NOT pull power plug from socket by the power cable.
1.1.9 DO NOT use this product with an extension cable.
1.1.10 DO NOT use worn or damage leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician.
1.1.11 Supply: 110Vac 1ph protected by a 25A delayed fuse or equivalent breaker.
1.1.12 fit a plug according to the following instructions (see diagram at right).
Ensure the unit is correctly earthed via a three-pin 110V 16A plug to suit supply (see 1.1.11).
a) Connect the gREEN/YEllOW earth wire to the earth terminal.
b) Connect the bROWN live wire to the live terminal 'l'.
c) Connect the bluE neutral wire to the neutral terminal, unmarked.
d) After wiring, check that there are no bare wires, that all wires have been
connected correctly, that the cable outer insulation extends past the cable restraint and
that the restraint is tight.
WARNINg! Be very cautious if using a generator to power the light. The generator must be self-regulating and stable with regard to

voltage, wave form and frequency. The output must be greater than the power consumption of the light. If any of these requirements
is not met the electronics within the light may be affected.
Note: The use of an unregulated generator may be dangerous and will invalidate the warranty on the light.
1.2.
GENERAL SAFETY
WARNING! Turn off the mains power supply before servicing or performing any maintenance.

If you use an extension lead the cable must be fully unwound from the drum.

DANGER! DO NOT direct the light into a person's eyes. All models have a very intense light

output which, if incorrectly used, could cause eye damage.
DO NOT use the light without the front glass shield. Avoid touching the glass shield as handling may

reduce its serviceable life and cause the glass to crack.
DO NOT use the light without the weather seals intact.

DO NOT use the light without the front glass shield.

DO NOT use the light near flammable, combustible or explosive liquids, solids, gases or equipment

Maintain the light in good condition. Repairs must only be undertaken by a qualified electrician (use an

authorised service agent).
Keep a minimum distance of 1 metre from the front of the light to any surface which is to be illuminated.

Locate the light in an adequate area for its function, keep area clean and tidy and free from unrelated

materials.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool

and dry and then store in a safe, dry, childproof area.
DO NOT install the light where it is likely to be knocked or hit.

DO NOT install in bathrooms, shower rooms, saunas or such locations.

2. INTRODUCTION
Portable weatherproof floodlight in die-cast aluminium housing with tubular steel framed stand. Features 18 SMD LEDs which give a 120° even
spread of light, longer working life and lower running costs than traditional halogen bulbs. suitable for lighting workshops and garages. supplied
with a Bs En approved 16A 110V plug.
© Jack sealey Limited
InstRuctIons foR:
PORTABLE FLOODLIGHT 18 SMD LED 110V
LED130110P.V2
MoDEL no:
Original Language Version Original Language Version
fig.1
LED130110P.V2 Issue: 1 - 15/04/14