Sealey LED120P Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTAnT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents, WarninGs, anD
cautions. use tHis ProDuct correctLy, anD WitH care for tHe PurPose for WHicH it is intenDeD. faiLure to Do so
May cause DaMaGe, or PersonaL inJury, anD WiLL inVaLiDate tHe Warranty.
1. safety instructions
1.1. PLuG & Mains PoWer suPPLy
 WarninG! it is the owner's responsibility to read, understand and
comply with the following:
You must check all electrical equipment and appliances to ensure that they are
safe before using. You must inspect power supply leads, plugs and all electrical
connections for wear and damage. You must ensure that the risk of electric
shock is minimised by the installation of appropriate safety devices. An RCCB
(Residual Current Circuit Breaker) should be incorporated in the main
distribution board. We also recommend that an RCD (Residual Current Device)
is used with all electrical products. It is particularly important to use an RCD
together with portable products that are plugged into an electrical supply not
protected by an RCCB. If in doubt consult a qualified electrician. You may
obtain a Residual Current Device by contacting your Sealey dealer. You must
also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical
appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a
year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical
appliances responsible for the safe condition of the appliance and the
safety of the appliance operator. If in any doubt about electrical
safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe
before connecting to the power supply. See 1.1.1. & 1.1.2. above and
use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and
overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical
connections for wear and damage and especially power connections
to ensure that none are loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as
the electrical power supply to be used and check that plugs are fitted
with the correct capacity fuse.
A 13amp plug may require a fuse smaller than 13amps for certain
products, see recommended fuse rating listed below.
1.1.7. Do not pull or carry the appliance by the power cable.
1.1.8. Do not pull plugs from sockets by the power cable.
1.1.9. Do not use worn or damaged leads, plugs or connections.
Immediately replace or have repaired by a qualified electrician.
A U.K. 3 pin 13amp plug with ASTA/BS approval is fitted. In case of
damage, cut off and fit a new plug according to the following
instructions (discard old plug safely). (UK only - see diagram).
Ensure the unit is correctly earthed via a three-pin plug. FOR
230 VOLT 13AMP PLUG SEE fig.1.
a) Connect the GREEn/YELLOW earth wire to the earth terminal
'E'.
b) Connect the bROWn live wire to live terminal 'L'.
c) Connect the bLUE neutral wire to the neutral terminal 'n'.
d) After wiring, check that there are no bare wires, that all wires
have been correctly connected, that the cable external insulation
extends beyond the cable restraint and that the restraint is tight.
© Jack Sealey Limited
fig.1
recoMMenDeD 230V
fuse ratinG: 3aMP
Original Language Version
InSTRUCTIonS foR:
LeD PortabLe
fLooDLiGHt 20W 230V
LeD120P
MoDEL no:
1.1.10. cable extension reels. When a cable extension reel is used it should
be fully unwound before connection. A cable reel with an RCD fitted is
recommended since any product which is plugged into the cable reel
will be protected. The section of the cores of the cable is important
and should be at least 1.5mm², but to be absolutely sure that the
capacity of the cable reel is suitable for this product and for others
that may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2. LiGHt reWirinG:
WarninG! ensure all cables are disconnected from the power

supply before attempting the 0following.
Should you need to re-wire the cable into the lamp, proceed as
follows: Remove back cover of the terminal box, located at the rear of
the lamp, to expose the connection block and wires, see fig.2.
Disconnect and remove the old mains cable.
1.2.1 Slide the gland nut and silicon cable seal over the new cable
before inserting it through the cable entry gland in the base of the
rear cover. before making the connections, pass the cable through
the cable clamp and tighten it as shown in fig.2.
a) Connect the GREEn/YELLOW earth wire to the earth terminal 'E'.
b) Connect the bROWn live wire to live terminal 'L'.
c) Connect the bLUE neutral wire to the neutral terminal 'n'.
After wiring, check there are no bare wires, that all wires have
been correctly connected and that the cable clamp and cable entry
gland nut are tight.
1.2.2 When wired, check that the weather proofing seal is correctly located in
the back cover recess and then replace the back cover. Do not use
worn or damaged leads, plugs or connections. Immediately replace or
have repaired. If in any doubt contact a qualified electrician.
fig.2
LED120P Issue: 1 - 20/07/12