Introduction: The Vizi Beam RXONE is a DMX intelligent, moving head fixture. This fixture has 3 oper- ating modes; sound active mode, show mode, and DMX control. This unit can be used as a stand alone unit or in a Primary-Secondary configuration.
B. The appliance has been exposed to rain or water. C. The appliance does not appear to operate normally or exhibits a marked change in perfor- mance. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 5...
Page 6
Pan/Tilt Speed Adjustment • Digital Display for Address and Function Setting Power Cord Daisy Chain (See Power Cord Daisy Chain section of this manual for details) • ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 6...
Page 7
Vizi Beam RXONE Product Registration The Vizi Beam RXONE carries a one year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly writ- ten on the outside of the return package.
WARNING! CAUTION! FIRE HAZARD! DUE TO THE EXTREME HEAT CAUSED BY THIS LAMP, THE MINIMUM DISTANCE TO LIGHTED OBJECTS IS 8 METERS (26FT). ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 8...
Page 9
NOTE: After replacing the lamp, the lamp time MUST be reset. The lamp time must be reset to gain access to the full system menu. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 9...
Page 10
The installation should be checked by a skilled person once a year. The Vizi Beam RXONE is fully operational in three different mounting positions: hanging upside-down from a ceiling, sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decoration etc.).
Page 11
Screw one clamp onto the Omega holders using an M12 screw and nut. Insert the quick-lock fas- teners of the first Omega holder into the respective holes on the bottom of the Vizi Beam RXONE. Tighten the quick-lock fasteners fully clockwise. Pull the safety-cable through the openings located on the base plate and over the trussing system or a safe fixation spot.
6. Fuse: Protects the unit from over-voltage or short circuit. 7. Power In/Out: Used to connect the unit to supply power. 8. DMX In/Out: 3-pin XLR connectors for DMX-512 operation. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 13...
Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The Vizi Beam RXONE can be controlled via DMX-512 protocol. The Vizi Beam RXONE has 2 DMX channel modes: 15 channels and 17 channels. The DMX address is set electronically using the controls on the front panel of the unit.
Page 15
5-pin data cables in to a 3-pin line, a cable adaptor must be used. These adaptors are readily available at most electric stores. The chart below details a proper cable conversion. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 15...
Page 16
• The Vizi Beam RXONE has two DMX channel modes: a 15 channel mode and 17 channel mode. See the Channel Mode sections of this manual for detailed descriptions of the DMX traits.
Last State - If the DMX signal is lost the fixture will stay in the last DMX set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up. 3. Press ENTER to confirm your desired set up. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 28...
Page 29
2. Press ENTER again, and “Reset” will be displayed. Press ENTER to reset the lamp time to 0. Only reset the lamp time when installing a new lamp. If you don’t wish to reset the lamp time press the MENU button. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 29...
Page 30
Reset - Use this function to reset the motors. 1. Press the MENU button until “Reset” is displayed, and press ENTER. 2. The fixture will now reset. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 30...
Page 31
“Color” is displayed. Press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 31...
Page 32
4. For each secondary unit, press the MENU button until “Pri/Sec” is displayed, and press ENTER. Choose either “Sec 1” or “Sec 2” and press ENTER. 5. The secondary units will now follow the primary unit. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 32...
Page 33
SOUND ON & OFF - Use the buttons to activate and deactivate sound active mode. SHOW 0 - Press this button to activate show mode. Use buttons 1-4 to find your desired show. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 33...
Lamp & Fuse Replacement Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized ADJ® service technician. Replacing with anything other than the specified part can dam- age your unit and will void your manufacturer’s warranty.
Page 35
Start by unscrewing the four phillips screws that hold the shell in place. Once the screws are unscrewed remove the shell. You will now have access to the lamp. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 35...
Replace the lamp by setting the lamp into the two bottom brackets, gently press the lamp down, and insert the top of the lamp into the lamp frame. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 36...
Page 37
Be sure the fuse holder is completely and properly seated. Unit does not respond to sound: • Quiet or high pitched sounds will not activate the unit. • Make sure that Sound Active mode is activated. ADJ Products, LLC - www.adj.com - Vizi Beam RXONE User Manual Page 37...