Page 1
ORDER NO.ODSD020319C2 DVD Player DVD-XV10E / DVD-XV10EB / DVD-XV10EG / DVD-XV10EE Colour (S).......Silver Type SPECIFICATIONS Specifications Power supply: AC220-240 V, 50 Hz 14 W Power consumption: Dimensions: 430 (W)×300 (D)×52 (H) mm (excluding protrusions) Mass: 2.9 kg Signal system: PAL 625/50, PAL 525/60,...
Page 2
Y output level: 1 Vp-p (75 C output level: NTSC; 0.286 Vp-p (75 PAL; 0.300 Vp-p (75 Output terminal: S terminal (1 system)/AV RGB video output: R output level: 0.7 Vp-p (75 G output level: 0.7 Vp-p (75 B output level: 0.7 Vp-p (75 Output terminal: AV (1 system)
1. SAFETY PRECAUTIONS 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
good earth ground such as a water pipe, as shown in Figure 1 3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6.
4. General Description 4.1. Operating instructions 5. Disassembling the Casing and Checking P.C.B.s 5.1. Dissasembly Procedure...
Page 7
5.2. Caseing Parts and P.C.B. Positions 5.3. Top Cover 1. Unscrew the screws.
Page 8
5.4. Tray 1. Insert the screwdriver into the tray open/close hole. 2. Move screwdriver from the left to the right to open the tray. 3. Remove the tray dressing from the tray section. 5.5. Front Panel 1. Remove the connectors...
Page 9
1. Unscrew the screws. 2. Release the tabs. 5.6. Mechanism Unit 1. Unscrew the screws. 2. Remove the connectors. 3. Pull out the mechanism unit vertically.
Page 10
5.7. Terminal P.C.B. 1. Unscrew the screws. 2. Remove the connectors. 5.8. Module P.C.B. 1. Unscrew the screws. 2. Remove the connectors. 3. Press each tab with the nipper to pull out the module PCB vertically.
Page 11
5.9. Front-1 P.C.B. and Front-2 P.C.B. 1. Unscrew the screws. 2. Release the tabs. 5.10. Rear panel 1. Unscrew the screws 2. Release the tabs. 5.11. Power P.C.B. 1. Unscrew the screws. 2. Remove the connectors.
5.13.2. Servicing position of the Mother P.C.B. and Power P.C.B. 5.13.3. List of the Extention Cables 6. PREVENTION OF STATIC ELECTRICITY DISCHARGE The laser diode in the traverse unit (optical pickup) may brake down due to static electricity of...
clothes or human body. Use due caution to electrostatic breakdown when servicing and handling the laser diode. 6.1. Grounding for electrostatic breakdown prevention Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity in the working environment. Proceed servicing works under the working environment where grounding works is completed.
times as possible. 3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the cable. 4. The half-fixed resistor for laser power adjustment cannot be adjusted. Do not turn the resistor. 7.
7.2. Cautions to Be Used Before Replacing the Optical Pickup Unit and Spindle Motor Assembly Before replacing the optical pickup unit and spindle motor assembly, check the total using hours for each of them. The checking method is as follows:...
Page 17
Cautions to be taken when replacing the optical pickup The optical pickup may break down due to the static electricity of human body. Take proper protection measures against static electricity before repairing the parts around the optical pickup. (See the page describing the PREVENTION OF STATIC ELECTRICITYDISCHARGE.) 1.
8. Self-Diagnosis Function and Service Modes 8.1. New servicing method for DVD player (5th generation models) With the 5th generation models new self-diagnosis function and new servicing method described below are additionally available. 8.1.1. Firmware updating and recovery with disc - Recovery - Firmware updating Simply run the recovery disc.
Page 19
8.1.2. New self-diagnosis function - Cumulative operation time display function (Spindle motor and DVD /CD laser) - Servo process display function - ADSC internal RAM display function - Other: Increased number of last errors storage 1event 20 events Utilization of the above functions, in combination with servicing procedures, is expected to contribute to higher efficiency of fault diagnosis.
Page 20
8.2.2. Updating firmware 1. Load the recovery disc RFKZD5TR006 on to the player and run it. 2. Firmware version of the player is automatically checked. Appropriate message appears whenever necessary. 3. Using remote controller's cursor key, select whether version updating is to be done or not. (Selection of Yes/No) 4.
Page 21
time is displayed. When servicing, check the timer display and use it as information for fault diagnosis. At the time of repair and replacement of these components, make sure to check the operation time and reset the timer after replacement. Operation time of the replacement parts (spindle motor and laser) is the valuable information as actual data for future product quality.
Page 22
Spindle motor operation time ..In STOP mode, main unit PAUSE +FWD-SKIP+ remote controller [6] To reset the timer, perform the following while displaying the time with above key operation. Laser operation time ..... In STOP mode, main unit STOP+FWD -SKIP+ remote controller [5] Spindle motor operation time ..
Page 23
When focus gain remains at initial value and tracking gain changes, fault exists before ADSC input. When focus gain changes and tracking gain remains at initial value, fault exists after ADSC output. [Tracking system] When focus gain remains at initial value and tracking gain changes, fault exists after ADSC output.
2 digits, normally 06, are ignored.) Picking up servo learned value (Determined) 1. Focus (primary)/tracking balance learning ... When leading in focus 2. Focus/tracking gain and equalizer ... When leading in tracking 3. Focus balance (secondary) ... When leading in tacking [Note] When fault exists somewhere after tracking servo, the disc type is switched by retry to make learned value different from the one in normal startup.
Error Error Content Additional error explanation Defect 1 Defect 2 Defect 3 Code F891 Message couldn’t Begin sending message to AV task be sent to AV task F893 FROM FROM CPU / falsification (IC6201) (IC6302) F894 EEPROM EEPROM Serial / abnormality communication (IC6303)
Page 29
8.9. Service mode table 2 Pressing various button combinations on the player and remote control unit can activate the service modes.
8.11. Servo Process Display Mode 8.12. Sales demonstration lock function This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCKED" is displayed on the unit, and ordinary operation is disabled.
8.12.2. Cancellation The lock can be cancelled by the same procedure as used in setting. ("UNLOCKED" is displayed on cancellation. Disconnecting the power cable from power outlet does not cancel the lock.) 8.13. Service Precautions 8.13.1. Recovery after the dvd player is repaired 8.13.2.
Page 36
Cautions to be taken when replacing the optical pickup The optical pickup may break down due to the static electricity of human body. Take proper protection measures against static electricity before repairing the parts around the optical pickup. (See the page describing the PREVENTION OF STATIC ELECTRICITYDISCHARGE.) 1.
Page 37
- An antistatic flexible sheet (FPC) is connected with the new optical pickup. / Cut antistatic flexible sheet (FPC) after optical pickup exchange.
Page 38
9.2. Exchange of a spindle motor - Even STEP1-STEP6 of item 9.1. is carried out. 9.3. Exchange of a feed motor - Even STEP1-STEP8 of item 9.1. is carried out. 9.4. Exchange of a traverse motor - Even STEP1-STEP4 of item 9.1. is carried out.
10. ADJUSTMENT PROCEDURES 10.1. Service Tools and Equipment Application Name Number Tilt adjustment DVD test disc DVDT-S15 or DVDT-S01 Hex wrench Available on sales route. Others Screw lock RZZ0L01 Grease (1) RFKXGUD24 Grease (2) RFKXPG641 Oil (1) VFK0749 Confirmation CD test disc PVCD-K06 or any other commercially available disc VCD test disc...
10.2. Important points in adjustment 10.2.1. Important points in optical adjustment - Before starting optical adjustment, be sure to take anti-static measures. - Optical pickup tilt adjustment is needed after replacement of the following components. 1. Optical pickup unit 2. Spindle motor unit 3.
Page 41
Measurement point Adjustment point Mode Disc Tangential adjustment T01 (inner periphery) play DVDR-S15 or DVDT screw Tilt adjustment screw T43 (outer periphery) play Measuring equipment Adjustment value None (Main unit display for servicing is used.) Adjust to the minimum jitter value. 10.4.1.1.
Page 42
Jitter value depends on the model: 1. If the jitter value changes like B, the optimum point is easy to find. 2. If the jitter value changes like A, set the optimum point near the middle. 10.4.1.3. Check after adjustment Play test disc or any other disc to make sure there is no picture degradation in the inner, middle and outer peripheries, and no audio skipping.
Page 43
10.4.1.4. Procedure for screw lock 1. After adjustment, remove the mechanism unit, cover, tray and terminal P.C.B. in this sequence. 2. Fix adjustment screw with screw lock. 3. After fixing, a cover, a tray, and a terminal P.C.B. are assembled and a mechanism unit is attached.
Page 44
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT BLACK DROP OUT...
Page 45
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATAOUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 46
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 47
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 48
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSSSIGNAL TRON TRACKING ON TRSON...
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPTREQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
17. REPLACEMENT PARTS LIST Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 55
*“<IA>-<ID>”,marks in Remarks indicate languages of instruction manuals. [<IA>: German/ Italian/ French/ Netherlands/ Swedish/ Danish, <IB>:Spanish/ Portuguese, <IC>: Russian, <ID>: English.] *All parts that are supplied by S.P.C.. Ref. No. Part No. Part Name & Description Remarks REP3265E-N MODULE P.C.B. (RTL) REP3273EA-M MOTHER P.C.B.
Page 56
Ref. No. Part No. Part Name & Description Remarks RSC0622 EARTH SPRING(B) RSC0623 EARTH PLATE RSC0652 EARTH SPRING(C) RMZ0629 BARRIER RMR1461-W PCB SUPPORT RQLS0233 LASER CAUTION LABEL RAF3011A OPTICAL PICK-UP A7P085 CLAMP PLATE C2A003 LOADING MOTOR C2G029 LOADING GEAR(1) B9G030 LOADING GEAR(2) B9G031 LOADING GEAR(3)
Page 57
Ref. No. Part No. Part Name & Description Remarks N2QAJB000037 REMOTE CONTROL ASS’Y A1-1 HTR028352001 BATTERY COVER RQT6314-D OPERATING INSTRUCTIONS (EG)<IA> RQT6315-E OPERATING INSTRUCTIONS (E) <IB> RQT6440-R OPERATING INSTRUCTIONS (EE)<IC> RQT6316-B OPERATING INSTRUCTIONS (E)(EE)(EB)<ID> RJA0019-2X AC CORD (E)(EE)(EG) RJA0053-3X AC CORD (EB) VJA0788-D A/V CORD...
Ref. No. Part No. Part Name & Description Remarks 18. Schematic Diagram for printing with A4 H020300000HP...
Page 71
MAIN SIGNAL JK3871 AV 21-PIN TERMINAL IC3001 IC4201 (AV DECODER) (2CH A/D CONVERTER) IC4311 OUTPUT AMP V OUTL MIXR MIX R OUT LOW-PASS FILTER 4x/8x ENHANCED AUDIO OVERSAMPLING AOUT0 DATA MULTI-LEVEL ADOUT0 92 SERIAL DIGITAL FILTER DELTA-SIGMA PORT WITH FUNCTION MODULATOR IC4311 CONTROLLER...
Page 72
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE AUDIO D/A CONVERTER SECTION (MODULE P.C.B.(5/6)) SCHEMATIC DIAGRAM...
Page 73
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE AUDIO OUT SECTION (MOTHER P.C.B.(2/2)) SCHEMATIC DIAGRAM...
Page 74
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE AV DECORDER SECTION (MODULE P.C.B.(3/6)) SCHEMATIC DIAGRAM...
Page 75
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE CPU SECTION (MODULE P.C.B.(6/6)) SCHEMATIC DIAGRAM...
Page 76
DVD-XV10E/EB/EG/EE INTERMEDIATE(FEP AND DRV) SCHEMATIC DIAGRAM...
Page 77
F FP5201 IBT12 F TC2507 F TC5214 F TP5214 F FP5202 IBT13 F TC2508 F TC5215 F TP5215 F PP2501 DVD-XV10E/EB/EG/EE (COMPONENT SIDE) IBT14 F TC2509 F TC5216 F TP5216 F PP2503 INTERMEDIATE(1/2) IBT15 F TC2510 F TC5217 F TP5217...
Page 78
MIXR OPENSW GAINH/L D+5V ADAC5V ADAC5V TRAYIN HFMON DGND AMUT AMUT TRAYREF AGND DGND ZFLAG ZFLAG TRAY/TRV TRAYMUT MECHANISM SPINDLE MOTOR UNIT FRONT P.C.B. PP2502 CLOSESW DGND POWER SW. P.C.B. LOADING OPENSW MOTOR INTERMEDIATE P.C.B. DVD-XV10E/EB/EG/EE INTER CONNECTION SCHEMATIC DIAGRAM...
Page 82
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page DVD-XV10E/EB/EG/EE AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page ODC SECTION (MODULE P.C.B.(2/6)) SCHEMATIC DIAGRAM...
Page 83
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE OPERATION SECTION(POWER SUPPLY P.C.B.(2/2)) SCHEMATIC DIAGRAM...
Page 84
MECHANISM UNIT MODULE P.C.B. MOTHER P.C.B. IC5201 IC2001 IC3001 IC4201 FRONT OPTICAL PICK UP PROCESSOR UNIT (FEP) IC7001 OPTICAL IC2501 DISC CONTROLLER (ODC) DIGITAL SPINDLE MOTOR MIXL SERVO MOTOR DRIVE IC6302 CONTROLLER AUDIO (ADSC) DECODER MIXR 8M bit (AV DEC) CONVERTER FLASH IC2511...
Page 85
DVD-XV10E/EB/EG/EE POWER SW AND OPERATION SW SCHEMATIC DIAGRAM...
Page 86
PRIMARY CIRCUIT SECONDARY CIRCUIT D1011 L1001 C1011,C1012 T1021 AC SOCKET P1001 D1002 SURGE LINE RECTIFIER KILLER FILTER F1001 IC6001 (SUB CPU) COM3 Q1125, COM0 Q1126 REG. D+2.5V SEG1 CINEMA POWER A+5V D6102 D6103 TRANSFORMER Q1115 S6164 SEG45 55 REG. D+5V Q1021,Q1052 BACK LAMP BACK LAMP...
Page 87
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE POWER SUPPLY SECTION (POWER SUPPLY P.C.B.(1/2)) SCHEMATIC DIAGRAM...
Page 89
RF SIGNAL MOTOR DRIVE SIGNAL TRACKING ERROR SIGNAL FOCUS ERROR SIGNAL IC7001 IC5201 (ODC) SPINDLE MOTOR (FRONT END PROCESSOR) REFNV RFENV TESTSG TSTSG DCAGC VREF1B IC2001 IC2501 (ADSC) (SPINDLE MOTOR DRIVE) SPINDLE TIL T TSTSG DFLTOP NARF DMV/FG NARF DFLTON HOLD CONT.
Page 91
MAIN SIGNAL IC3501-32 IC3501-29,30 IC3501-24,25 2.0Vp-p(20usec./div.) 1.5Vp-p(20usec./div.) 2.0Vp-p(20usec./div.) IC3501 (VIDEO BUFFER) 1.5-6MHz C OUT C OUT VBOUT 119 75Ω B.P.F. 75Ω S2-VIDEO V OUT V OUT 6MHz VYOUT 134 L.P.F. YOUT Y OUT 75Ω IC3801 (V/Y SELECT SW) JK3871 AV 21-PIN TERMINAL IC3201 IC3821...
Page 92
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE VIDEO D/A CONVERTER SECTION (MODULE P.C.B.(4/6)) SCHEMATIC DIAGRAM...
Page 93
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE VIDEO OUT SECTION (MOTHER P.C.B.(1/2)) SCHEMATIC DIAGRAM...
Page 94
MODULE P.C.B. POWER SUPPLY P.C.B. Transistor-resistors Transistor TC6029 CP6231 C CP7037 F TC4212 Q1021 TC6030 QR6301 C CP6232 C CP7038 C TC4213 Integrated Circuits CP6233 C CP7039 C TC4214 Q1031 TC6031 IC2001 F CP6301 F CP7040 C TC4215 Q1051 TC6032 IC3001 C CP6302 C TC2001...
Page 97
14.2. POWER SUPPLY SECTION (POWER SUPPLY P.C.B. (1/2)) SCHEMATIC DIAGRA POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page...
Page 98
C DIAGRAM DVD-XV10E/EB/EG/EE POWER SUPPLY SECTION (POWER SUPPLY P.C.B.(1/2)) SCHEMATIC DIAGRAM...
Page 99
14.3. OPERATION SECTION (POWER SUPPLY P.C.B. (2/2)) SCHEMATIC DIAGRA POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page...
Page 101
14.4. VIDEO OUT SECTION (MOTHER P.C.B. (1/2)) SCHEMATIC DIAGRAM POWER SUPPLY SECTION(PW VIDEO OUT SECTION(VO):Pa ADSC SECTION(ADSC):Page AV DECORDER SECTION(AVD AUDIO D/A CONVERTER SEC...
Page 102
Y SECTION(PW):Page OPERATION SECTION(OP):Page CTION(VO):Page AUDIO OUT SECTION(AO):Page N(ADSC):Page ODC SECTION(ODC):Page SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page NVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE VIDEO OUT SECTION (MOTHER P.C.B.(1/2)) SCHEMATIC DIAGRAM...
Page 103
14.5. AUDIO OUT SECTION (MOTHER P.C.B. (2/2)) SCHEMATIC DIAGRAM POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page...
Page 110
POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE AV DECORDER SECTION (MODULE P.C.B.(3/6)) SCHEMATIC DIAGRAM...
Page 111
14.9. VIDEO D/A CONVERTER SECTION (MODULE P.C.B. (4/6)) SCHEMATIC DIAG POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page...
Page 114
C DIAGRAM POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page DVD-XV10E/EB/EG/EE AUDIO D/A CONVERTER SECTION (MODULE P.C.B.(5/6)) SCHEMATIC DIAGRAM...
Page 115
14.11. CPU SECTION (MODULE P.C.B. (6/6)) SCHEMATIC DIAGRAM POWER SUPPLY SECTION(PW):Page OPERATION SECTION(OP):Page VIDEO OUT SECTION(VO):Page AUDIO OUT SECTION(AO):Page ADSC SECTION(ADSC):Page ODC SECTION(ODC):Page AV DECORDER SECTION(AVDEC):Page VIDEO D/A CONVERTER SECTION(VD):Page AUDIO D/A CONVERTER SECTION(AD):Page CPU SECTION(CPU):Page...
Page 116
DVD-XV10E/EB/EG/EE CPU SECTION (MODULE P.C.B.(6/6)) SCHEMATIC DIAGRAM...
Page 117
14.12. INTERMEDIATE (FEP AND DRV) SCHEMATIC DIAGRAM...
Page 118
DVD-XV10E/EB/EG/EE INTERMEDIATE(FEP AND DRV) SCHEMATIC DIAGRAM...
Page 119
14.13. POWER SW AND OPERATION SW SCHEMATIC DIAGRAM...
Page 120
DVD-XV10E/EB/EG/EE POWER SW AND OPERATION SW SCHEMATIC DIAGRAM...
Page 122
Ref No. IC2001 MODE PLAY STOP Ref No. IC2001 MODE PLAY STOP Ref No. IC2001 MODE PLAY STOP IC2001 Ref No. MODE PLAY STOP IC2001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001...
Page 123
IC3201 Ref No. MODE PLAY STOP IC3201 Ref No. MODE PLAY STOP Ref No. IC3201 MODE PLAY STOP IC4201 Ref No. MODE PLAY STOP IC6201 Ref No. MODE PLAY STOP IC6201 Ref No. MODE PLAY STOP IC6201 Ref No. MODE PLAY STOP IC6201...
Page 124
IC3501 Ref No. MODE PLAY STOP IC3501 IC3581 IC4301 Ref No. MODE PLAY STOP IC3801 Ref No. MODE PLAY STOP IC3821 Ref No. MODE PLAY STOP IC3822 Ref No. MODE PLAY STOP IC4311 IC4391 Ref No. MODE PLAY -12.0 11.3 -12.0 11.3 STOP...
Page 125
IC1101 IC1151 Ref No. MODE PLAY STOP 10.6 IC6001 Ref No. MODE PLAY STOP IC6001 Ref No. MODE PLAY STOP IC6001 Ref No. MODE PLAY STOP IC6001 Ref No. MODE PLAY STOP IC6001 Ref No. MODE PLAY STOP IC6011 Ref No. MODE PLAY STOP...
Page 126
IC2501 Ref No. MODE PLAY STOP IC2501 Ref No. MODE PLAY STOP IC2511 Ref No. MODE PLAY STOP IC2511 Ref No. MODE PLAY STOP IC5201 Ref No. MODE PLAY STOP IC5201 Ref No. MODE PLAY STOP IC5201 Ref No. MODE PLAY STOP Ref No.