Coin Cell Battery - DeWalt DCD992 Operating Instructions Manual

English
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector that allows
3 modes 17 to be customized using the Tool Connect™ app.
Home settings are active when the home indicator
Refer to Table 1 for customizable features.
Once configured, pressing the mode button
the tool will cycle through the modes
If you are unsure of the current configuration, press the mode
selector button to set the tool to the Home setting (home
14
indicator 16 is lit).
D WALT Tool Connect™
e

WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™ interaction.
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button
14
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://
www.bluetooth.com/Pages/Bluetooth‑Smart‑Devices‑List.aspx)
D WALT Tool Connect™ is an application for your smart device
e
(such as a smart phone or tablet) that connects the device to
your tool to allow you to configure specific tool functions. Refer
to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
• Follow the instructions in the app to create your Tool
Connect™ account.
TABlE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM) Speed 1
in Drill Mode
Speed 2
Speed 3
Bind‑Up Control®
12
16 is lit.
14 on the foot of
17 .
(Fig. D) to set the tool to the
Home
MED
20 secs
450
1300
2000
Disabled Disabled
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
• To connect your tool with the D
app, at the appropriate screen, press the mode selector
button for 3–5 seconds, then wait for the tool to
14
connect. The tool can only be connected to one Tool
Connect™ account at a time.
Once the tool has been connected, you can confirm that you
would like to register the product.D

Coin Cell Battery

Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D WALT service center. Do not attempt to replace the coin cell
e
battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithium salts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
Factory Presets
Mode 1 Mode 2
OFF MED
20 secs 20 secs
450 450
1300 1300
2000 2000
Disabled
WALT Tool Connect™
e
WALT.com account.
e
Customizable
Mode 3 Range
HIGH OFF‑HIGH
20 minutes 0–20 minutes
450 140–450
1300 400–1300
2000 600–2000
Disabled/
Disabled
Enabled