Related Manuals for Shark 800-00-36
Summary of Contents for Shark 800-00-36
- Page 1 Lithium Jump Starter & Portable Power Supply User Guide MODEL: 800-00-36 CAPACITY: 10000mAh...
- Page 2 FULLY CHARGE IMMEDIATELY AFTER PURCHASE. Fully recharge after each jump starting, or every 3 months to ensure long battery life. Please read and understand all important safety and operating instructions before using this item. In addition, please read and follow all vehicle and battery manufacturers’...
-
Page 3: Important Safety Instructions
These items may produce a short-circuit that can cause severe burns. 5) To avoid damage to the vehicle’s electrical system, do not use the 800-00-36 on a vehicle that has no battery installed. 6) Use of an accessory not recommended or sold by the manufacturer may result in a risk of fire, electric shock or injury to persons. - Page 4 This item can instantly jump start most single battery vehicles, up to 50+ (over 50) times on a fully charge. The 800-00-36 is also equipped with USB power output, LED flash light, 19VDC power output and 12VDC power output.
- Page 5 12V Output 10A Max Operating Temperature -10℃ ~ +50℃ Charging Temperature 10℃ ~ +45℃ Product Layout: Flash Ught Button Battery Status Indicator Power Button 15V/1A Input Port Enging Start Socket USB Port 12V/10A Port ABOUT SMART JUMPER CLAMPS Green LED...
- Page 6 EC5 Plug Negative Clamp Positive Clamp Red LED BOOST Button “BOOST” Mandatory Operations: 1) If with correct connection between Jump Starter and vehicle battery (Red LED keeps on and green LED is off), press and hold BOOST button for 3 seconds (after a buzzer sound, the green LED is on and red LED is off).
- Page 7 and high heat if not used properly. LED and Buzzer Communication: Buzzer Red LED Green LED Condition Sound Jumper cable and One sound EPS-204 are connected. Jumper cable and vehicle battery are One sound connected. Ready to start the engine. Lithium battery voltage Slow flash No buzzer...
-
Page 8: Connecting To The Battery
are connected with each other. Reverse connection of Fast flash Fast buzzer clamps. Fast flash No buzzer Engine is started. Vehicle’s battery voltage Fast flash No buzzer is higher than Jump Starter’s. CONNECTING TO THE BATTERY 1) Identify polarity of battery posts. The positive battery terminal is typically marked by these letters or symbol (POS,P,+). -
Page 9: Jump Starting
1) This unit is only for emergency use, not for frequent commercial use! ENGINE START socket is ALWAYS activated! Do not attempt to jumpstart your vehicle when the 800-00-36 battery capacity is below 25% (battery status indicator: 1 solid LED lit). - Page 10 3 months even if this unit has not been used. If battery voltage in the 800-00-36 is too low, this item will shut off to prevent damage to itself. Recharge the unit as soon as possible to be activated and fully charge it to ensure long battery life.
- Page 11 The indicator LEDs will flash one by one during the period of charging. Different number of indicator LEDs shows different storage level of 800-00-36. Indicator Unlit LEDs Flashing Solid Solid Solid Solid Storage 5% ~ ˂ 5% Level 100%...
-
Page 12: Usb Power
USB POWER Connect the USB device to the 800-00-36 with either the original cable or the included multi-tip cable (better use original cable of Apple® for Apple® products). Press Power button to start USB power. When disconnected, the 800-00-36 will automatically shut off. - Page 13 unauthorized personnel or other causes not arising out of defects in materials or workmanship. Official Distributor ASP Group s.r.o. Staroplzenecka 290 326 00, Letkov Czech Republic tel.: +420 378 21 21 21 E-mail: info@aspgroup.cz www.aspgroup.eu...