Sign in today to find solutions:

Don't have an account? Sign up

D-link DWL-G510 Install Manual

D-link dwl-g510 : install guide.

 
This product works with the following operating
Windows XP, Windows
system software:
2000, Windows Me, Windows 98SE
Before You Begin
You must have at least the following:
A desktop computer with an available 32-bit PCI slot
At least a 300 MHz processor and 32MB of memory
An 802.11g or 802.11b Access Point (for Infrastructure Mode) or another
802.11g or 802.11b wireless adapter (for Ad-Hoc; Peer-to-Peer networking
mode.)
Check Your Package Contents
These are the items included with your DWL-G510 purchase:
If any of the above items are missing, please contact your reseller.
Insert the D-Link CD-ROM Into Your
Computer
Turn on the computer
Insert
the
D- Link AirPlus G DWL-G510
Driver CD in the CD-ROM drive.
The step-by-step instructions that follow are shown
in Windows XP. The steps and screens are similar
for the other Windows operating systems
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
DWL-G510 AirPlus G 2.4GHz Wireless PCI Adapter
CD-ROM (containing Drivers, Manual and Warranty)
and
TM
specifications subject to change without notice. DWL-G510 v1.00
TM
Wireless PCI Adapter
into your computer
before installing the
driver software from
the D-Link CD!
1
DWL-G510
TM
AirPlus G 2.4GHz
Wireless PCI Adapter
Do
NOT
install
the DWL-G510
Next page ->

Summary of Contents

  • Page 1

    Windows XP. The steps and screens are similar for the other Windows operating systems ©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. DWL-G510 v1.00 DWL-G510 AirPlus G 2.4GHz...

  • Page 2

    Continued... Click Install Drivers If the CD Autorun function does not automatically start on your computer, type “D:\Drivers\setup.exe.” If it does start, proceed to the next screen. Click Next Click Next Select No I will restart my computer later Click Finish Shut down your computer...

  • Page 3

    Make sure to turn off your computer and unplug the power cord. Remove the back cover of the computer. Install the DWL-G510 carefully and firmly seat it into an available PCI slot (which is usually “white” or “cream” colored). Secure the DWL-G510 back panel shield with a screw.

  • Page 4

    Restart Your Computer When you restart your computer this Found New Hardware Wizard (Windows XP) may appear: Select Install the software automatically (Recommended) Click Next For Windows XP: This Installation alert screen will appear. Click Continue Anyway Click Finish to finalize the installation.

  • Page 5

    Your Installation is Complete! After you’ve continued in Windows 2000, ME, or 98SE, the D-Link AirPlus G DWL-G510 Configuration Utility will automatically start and the utility icon will appear in the bottom right hand corner of the desktop screen (systray). If this...

  • Page 6

    Appendix For Windows XP, if you wish to use the AirPlus G utility, please do the following steps. Click the XP Networking icon to use the Zero Configuration Wireless Settings. Click Advanced Uncheck “Use Windows to configure my wireless net- work settings.”...

  • Page 7

    Displays the Link Quality for the DWL- G510 wireless connection to the access point. The Signal Strength represents the wireless signal between the access point and the DWL-G510. The percent- age coincides with the graphical bar. TxRate: The default setting is Auto;...

  • Page 8

    Router or Access Point. Channel: By default, the channel is set to 6. Channel selection is automatically adjusted by the DWL-G510 depending on the channel setting of the access point selected for association. To change the channel settings, the Wireless Mode must be set to Ad-hoc.

  • Page 9

    Go to Start > right click on Places > select Properties click on the Network Connection associated with the DWL-G510. Click Internet Protocol (TCP/IP) Click Properties Dynamic IP Address setup Used when a DHCP server the local network. (i.e. Router)

  • Page 10

    For Windows 2000 users: Go to Start > Settings > Dial-up Connections > Double-click on Local Area Connection with the DWL-G510 > select Click Internet Protocol (TCP/IP) Click Properties Dynamic IP Address setup Used when a DHCP server the local network. (i.e. Router)

  • Page 11

    Notes...

  • Page 12

    You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: