Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Boss Audio Systems BV9341
-
Page 2: Table Of Contents
Content Accessories ………………………………………………………………………………………………………………………………………... Unit Installation ……………………………………………………………………………………………………………………………….. Wire Connection ……………………………………………………………………………………………………………………………… Parking Brake Connection ……………………………………………………………………………………………………… Speaker connection ………………………………………………………………………………………………………………………. Button Description …………………………………………………………………………………………………………………………. Remote Control ……………………………………………………………………………………………………………………………….. Main Menu …………………………………………………………………………………………………………………………………………... Radio Operation ………………………………………………………………………………………………………………………………. DVD Operation ……………………………………………………………………………………………………………………………….. USB /SD Operation ……………………………………………………………………………………………………………………….. Settings Operation ……………………………………………………………………………………………………………………….. Aux in Operation ……………………………………………………………………………………………………………………………. -
Page 3: Accessories
Accessories Package contains the following accessories for installation and operation of the unit. (1) Washer, Spring (5) Rubber Washer, Cushion M5 Nut (2) Screw (6) Screw Left (7)installation (3) Bolt bracket Right (4) Mounting Strap Remote Control User Manual Power Cable Trim Ring... -
Page 4: Unit Installation
Unit Installation Bracket Screw 1. Put the 2 brackets to the left and right side of the unit; 2. Use screws to fix the brackets to the unit. Wire Connection The Description of the Input/output Interface... -
Page 5: Parking Brake Connection
Parking Brake Connection 1. In order for videos to be viewed, and to comply with federal and local laws, the parking brake wire must be connected to the power side of the parking brake switch. Connecting the reversing line to taillight on the car... -
Page 6: Speaker Connection
Speaker Connection After connecting, when you start up the reverse gear, the unit will receive the picture from car rear view camera. Note: Use only with 4-8 ohm, non-chassis grounded speakers Always observe correct polarity Loudspeaker cables and/or optional external power amplifiers must always be about 11.8 inch away from the antenna and/or antenna extension parts. -
Page 7: Button Description
Button Description 1. IR Sensor IR Remote control signal receiving window. Max distance is 6-8 meters, 45 angels. 2. RST Press it with a thin, sharp object, the device will then be reset to factory default settings. 3. MODE BUTTON Press mode button to change mode. -
Page 8: Remote Control
Remote Control 1: MODE 2: POWER 3: UP 4: BAND/RANDOM 5: ENTER 6: LEFT 7: DOWN 8: EJECT 9: STEREO/MONO 10:P.SCAN/REPEAT 11: SEEK-/BACKWARD 12: LOUD 13: STOP/PBC 14: OSD 15: PLAY/PAUSE 16: MUTE 17: MENU 18: SUBTITLE 19: RIGHT 20: SETUP 21: ANGLE 22: ROOT 23: VOLUME UP... - Page 9 Remote Control 10. P.SCN/ RPT In DVD mode, press to repeat REP 1 => REP Title => REP ALL. In SD /USB mode ，press to repeat REP 1 => REP Dir => REP ALL. In radio mode, PS (preset scan): Press to scan all preset stations in the memory of the current band and stay on each memory stations for about 5 seconds.
- Page 10 Remote Control / SEEK + buttons In DVD mode, press button to skip to the next track, press and hold button for two seconds to activate fast forward (FF) search in a track. In radio mode, press and hold button to select station forward automatically, touch again will stop select station.
-
Page 11: Main Menu
Main Menu The best way to discover the program is to explore each screen in detail, and to find out how to move from one to another. Read this chapter for a guided tour. Unit starts by displaying the main menu. This is the root of the screen hierarchy, and you can simply access all features by tapping on the touch screen buttons. -
Page 12: Dvd Operation
DVD Operation DVD Player To start DVD player, tap on DVD button from main menu screen. Touch Screen Menu You will not see any buttons while DVD is played, buttons will appear when you tap on TFT screen. Tap the screen again to hide the buttons, slide the subtitle part of bottom screen to switch the following 2 pages. -
Page 13: Usb/Sd Operation
Settings Operation Setting Control The BV9341 has default system setting, you can customize the settings to suit your personal needs. Once you change settings, your new settings will remain until you change it again. To start setting, tap it on main menu. - Page 14 Settings Operation Tap Wallpaper button to setup wallpaper Tap Panel Adjust button to setup panel touch Tap center of the and hold at least 2S, after five point, then it will show OK in the picture. and press OK exit calibration mode. Tap time setting button to setup time Tap SWC item to program SWC There are 3 wires for...
- Page 15 Settings Operation [1].Subtitle Lang setting: With this option you can select the preferred language for the subtitles. When the selected language is recorded on the disc then this language will automatically be shown. If not, the first language recorded on the disc is displayed. [2].Audio Lang setting: With this option you can select the preferred language for the audio output.
-
Page 16: Aux In Operation
Settings Operation Subwoofer Connect the subwoofer to the unit using sub output (see electrical diagram), tap menu on screen enter into main menu setting choose setting menu., choose sound and set subwoofer on to enable subwoofer. Parking When the car is stopped and the parking brake is working, the screen can display the video image, otherwise the screen can't display the video image. -
Page 17: Notes Of Disc
Notes of Disc Use only with 4-8 ohm, non-chassis grounded speakers Always observe correct polarity Loudspeaker cables and/or optional external power amplifiers must always be about 11.8 inch. away from the antenna and/or antenna extension parts. If want to display for 6.2” TFT, parking wire must be connected to ground. -
Page 18: Troubleshooting
Troubleshooting Symptom Cause Remedy Replace with fuse of the same amperage. If Power does not turn Fuse is blown the fuse blows again, consult your store of purchase (No sound is produced) In correct wiring Consult your local retailer 1. Turn off the unit 2. - Page 19 Troubleshooting symptom Cause Solution If the power supply is properly connected The car ignition is not on to the car accessory switch the ignition key to “ACC” No power The fuse is blown Replace the fuse Presence of disc inside the Remove the disc in the player then put a Disc cannot be loaded player...
-
Page 20: General Specification
General Specification General Power supply 11~16V DC Current consumption Max. 10 A Maximum power output 80W x 4 channels (max) Compatible formats DVD ±R/RW Video, CD ±R/RW Audio & Video Dimensions (W x D x H) / weight 6.5” x 7.0” x 3.9” /4.6 lbs Working temperature range -4°F -- +140°F ESP function...