Download Print this page
Philips DVP3366K Service Manual
Hide thumbs Also See for DVP3366K:

Advertisement

Quick Links

Service Manual
. Technical Specifications.........................................................1-2
. Safety Instruction, Warning & Notes........................................1-3
. QSG & DFU Instruction..................................................................2-1
. Mechanical and Dismantling Instructions....................................3-1
. Software Version & Upgrades, Region Code Change.................
. Trouble Shooting Chart......................................................
. Wiring Diagram..................................................................6-1
. Electrical Diagrams and Print-layouts......................................7-1
. Set Mechanical Exploded view & Part list................................8-1
. Revision List..................................................................................9-1
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by FK - 910 BU AVM
Version 1.0

TABLE OF CONTENTS

Printed in The Netherlands
Subject to modification
DVP3366K
DVP3366K/93
Page
4-1
.
5-1
.
CLASS 1
LASER PRODUCT
314 785 33650
GB
PHILIPS

Advertisement

loading

Summary of Contents for Philips DVP3366K

  • Page 1: Table Of Contents

    . Electrical Diagrams and Print-layouts..….…………………..….…7-1 . Set Mechanical Exploded view & Part list.…………………..….….8-1 . Revision List..................9-1 ©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or CLASS 1...
  • Page 2 Specifi cation Audio performance • DA converter: 24 bits, 192 kHz • Frequency response: • DVD: 4 Hz - 22 kHz (48 kHz); Note 4 Hz - 44 kHz (96 kHz) • SVCD: 4 Hz - 20 kHz (44.1 kHz); •...
  • Page 3: Safety Instruction, Warning & Notes

    Safety instruction, Warning & Notes Safety instruction 1. General safety 2.Laser safety Safety regulations require that during a repair: This unit employs a laser. Only qualified service personnel . Connect the unit to the mains via an isolation transformer. may remove the cover, or attempt to service this device .
  • Page 4 Warning 1.General 2. Laser . All ICs and many other semiconductors are susceptible to . The use of optical instruments with this product, will increase eye hazard. electrostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during .
  • Page 5 - lead free BGA-ICs will be delivered in so-called respected by the workshop during a repair: ‘dry-packaging’ (sealed pack including a silica gel Use only lead-free solder alloy Philips SAC305 with pack) to protect the IC against moisture. After order code 0622 149 00106. If lead-free solder-paste is...
  • Page 6 The following excerpt of the Quick Start Guide serves as an introduction to the set. The complete Direction For Use can be download in different languages from www.philips.com/welcome Philips Customer Contact & Support site:www. p4c.philips.com 2009 © Koninklijke Philips N.V. All rights reserved.
  • Page 7 COMPONENT VIDEO IN English DIVX(R) HDMI IN...
  • Page 8 Product overview Remote control Main unit (Standby-on) • Turn on the DVD player or switch to standby mode. Disc compartment Display panel Z (Open/Close) • Open or close the disc compartment. u (Play/Pause) (Standby-On) • Start, pause or resume disc play. •...
  • Page 9 v V b B (Navigation buttons) AUDIO/CREATE MP3 • Navigate through the menus. • Select an audio language/channel. B) or fast- • Search fast-forward ( • Access the menu to create MP3. backward (b). Press repeatedly to x (Stop) change the search speed. •...
  • Page 10: Mechanical And Dismantling Instructions

    Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1). Figure 1 Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first.
  • Page 11 Mechanical and Dismantling Instructions Detailed information please refer to the model set. Dismantling Instruction Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3). Note: Make sure to operate gently otherwise the guider would be damaged. Figure 3 Step4: Dismantling Front Panel, disconnect the connectors (XP5, XP6.
  • Page 12 Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. Figure 5 Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that connects the loader and the bottom cabinet. (Figure 5 & 6) Figure 6...
  • Page 13 Mechanical and Dismantling Instructions Dismantling Instruction Detailed information please refer to the model set. Step6: Dismantling Main Board, first disconnect the connector (XP1), and then remove 5 screws. (Figure 7) Step7: Remove the 2 screws on Power Board to dismantle the Power Board. (Figure 7) Figure 7...
  • Page 14 Software upgrade Preparation to upgrade software 1) Start the CD Burning software and create a new CD B. Read out the software versions to confirm upgrading project (Data Disc) with the following setting: Power on the set and press <Setup> button on the remote control.
  • Page 15: Trouble Shooting Chart

    Trouble shooting chart Spindle motor does not move Motor no move Check the FFC connection Correct connection between 24P and the loader. Check whether “M5V” Check the M5V power supply (+5V) voltage is normal. Check whether laser voltage Check/Replace Q5,Q6,Q7,Q8. (1.9V for CD &...
  • Page 16 Trouble shooting chart The power can not be on or off The power can’t be on or off Check the power supply Repair the power board on the power board is normal. Check if the XS301 on the Check/Correct front board to XP5 on the connection decoder board is in good contact.
  • Page 17 Trouble shooting chart All output voltages on the power board is 0V or deviated. All output voltages on the power board is 0V or deviated Check whether Replace F1 F1 is blown Replace C1&C2 if D1, D2, D3, D4 are Check whether there is normal.
  • Page 18 Trouble shooting chart Disc cannot be read . Disc cannot be read. Check the FFC connection Check the loaded circuit between 24P and the loader. 1.Check voltage on pin 23 of U1 varies between 0 and 3.3V: Check whether there is laser 3.3V for CD voltage (1.9V for CD and 2.4V for 0V for DVD...
  • Page 19 Trouble shooting chart Only DVD disc or only disc except DVD can be played Only DVD disc, or only disc except DVD can be Played. Check Check the loaded circuit connection between 24pin and the loader. Check laser voltage (2.4V) output Check the solder status on U1 and on L10, if pin18 of U1 is at low peripheral components...
  • Page 20 Trouble shooting chart No display on LED, and buttons do not work No display on LED, and buttons do not work Check whether there is correct contact between Correct connection XS301 and XP5 Check VCC(+5v) voltage Fix power supply board top a power supply for should on the power and front electric circuit...
  • Page 21 Trouble shooting chart Distorted audio and loud noise Distorted audio and loud noise Check the power supply voltages Check Q3 +12V to the operation amplifying Q3 is normal. Check whether the muting transistor Replace R84, R94,R100,R107,R116,R124 R84,R94,R100,R107,R116,R124 are normal Check whether muting Replace Q11~Q19...
  • Page 22 Trouble shooting chart Abnormal color of video picture Abnormal color of video picture Check whether Check Y2, R20,R27,C22 and C23 27MHz output signal Check whether the 3.3V Check other of power supply electric and 1.8V power supply circuit voltages on the decoder board are normal.
  • Page 23 Trouble shooting chart Remote reception is insensitive or fails. Remote reception is insensitive or fails. Check if the remote Check battery control works properly. Check if the power supply Check R315 C315 voltage to the remote censor is normal Use an oscilloscope to check if there is output waveform from the first pin IR of the REM301(PIN1 - RC waveform) remote censor after pressing button on the...
  • Page 24 Trouble shooting chart 5-10 No video picture, no sound. No video picture, no sound. Check whether all the voltages from the power board to the Check the loaded circuit CVBS(R21 point) waveform decoder board are normal. Check if the reset circuit consisting ofCE7, D2 is normal (at a low level Change CE7, D2.
  • Page 25: Wiring Diagram

    DVP3366K 6CH WIRING DIAGRAM REAR R HDMI COAX CENTER REAR L CVBS VIDEO LPF AUDIO AMP&LPF POWER SUPPLY 24PIN*0.5 XS201 1 2V 5PIN*2.5 MT1389DXE/M LIMIT LOAD- LOAD+ 5PIN*2.0 TROUT TRIN 11PIN*2.0 16M Serial FLASH MAIN BOARD 4PIN*2.0 1 2V USB_DM...
  • Page 26 Front Board Electric Diagram R315 REM301 LED+ 100 ohm R318 LED- STB_LED POWER_K1 100R/NC POWER_K XS302 C306 CE301 CON4(2.0) XS301 C315 0.1u 47uF WAKE_SW C316 C307 C308 100p 100p 100p for dvp331x R320 V CC DATA DATA POWER_K STB_LED R303 R304 R305 CON11(2.0)
  • Page 27 Switch Board Electric Diagram K303 POWER LED3 CON4(2.0) C319 C317 C318 SWITCH BOARD...
  • Page 28 OK Board & USB Board Electric Diagram R210 12VA R202 12VA C201 CE200 CE201 0.1u 22uF 22uF R203 C205 R205 180K P601 R211 KARAOKE INPUT C210 R201 U200A C211 100K 5.6K 2.2uF 2.2uF R200 C203 NJM4558 3.5mm NJM4558 1000p MIC_OUT 12VA C208 100p...
  • Page 29 Power Board Electric Diagram T2AL/250ac NTC 10&20 1N4007 1N4007 CON1 C N1 AC INPUT 680uH AC INPUT 10K471 + C1 + C2 1N4007 1N4007 10uF/400V(250V/450V) 15uF/400V(250V/450V) EEL19 FR102 10uF/50V CON2 152/1KV 1/4W120K 1/4W120K -22V +12V IN4007 FR102 1/6W10k 47uF/25V 6X2.5 HEADER 104/50V SR360/SR340 6.8uH...
  • Page 30 Main Board Electric Diagram: Power Supply TO POWER BOARD 5pin/2.5mm MO_VCC +5VD 960mA FB AXIAL N C/0 89M_3V3 +5VP G ND +P12V G ND SS8550 MO_VCC 0.1uF TO FRONT PANEL R120 R115 R118 +12V: +12V(+-10%) 4.7K/NC 4.7K/NC 4.7K/NC +5V: +5V(+-2.5%) 6PIN/2.0mm +12V VSDA...
  • Page 31 Main Board Electric Diagram: MT1389M 89M_3V3 OFF-PAGE CONNECTION A DACVDD APLLVDD3 DV33 DQ[0..15] DQ[0..15] 4 0.1uF R126 0 RFV18-1 + CE14 BAT54C 0.1uF 0.1uF DA CVDD3 MA[0..11] MA[0..11] R127 RFV18-2 100uF/16V 0.1uF DQM[0..1] DQM[0..1] SP-A BA [0..1] 0.1uF BA[0..1] 0.1uF 0.1uF 0.1uF Crystal...
  • Page 32 Main Board Electric Diagram: SDRAM & FLASH SDR_DRAM (Dual Layout) D Q0 D Q1 D Q2 D Q3 D Q4 SD33 D Q5 D Q6 SDCKE D Q7 OFF-PAGE CONNECTION D Q8 D CS# D Q9 MA10 DQ10 A10/AP DQ10 DQ[0..15] MA11 DQ11...
  • Page 33 Main Board Electric Diagram: VIDEO OUT & AV-CONNECTOR R /V_O 0R/1.8uH OFF-PAGE CONNECTION 75 1% 100pF CVBS_OUT CVBS_OUT B /U_O 0R/1.8uH VIDEO I/F 75 1% 100pF R /V_O CVBSO B /U_O G /Y_O PESD3V3L5UY/NA G /Y_O 0R/1.8uH 75 1% 100pF CE16 CVBS_OUT CVBSO...
  • Page 34 Main Board Electric Diagram: AUDIO OUTPUT OFF-PAGE CONNECTION 30K 1% 100pF MO_VCC 5.1K 9012 CE18 L CH 10K 1% r efa NJM4558 OPA R100 10uF/16V 4.7K +12VA 1000pF 100K +12VA A RF NC/1000pF A RF R133 C102 A_MUTE r efa A_MUTE AS PDIF 2N3904...
  • Page 35 7-10 7-10 Main Board Electric Diagram: HDMI I/F OFF-PAGE CONNECTION DV33 DV33 (2,3,4,7) V CC (2,3,7) Power Differential Signal ! TXC+ TXC+ No through hole & length less than 5cm ! TXC- TXC- 100 ohm - Impedance TX0+ TX0+ TX2+ TX0- TX0- TX2-...
  • Page 36 7-11 7-11 Main Board Print-layout (Bottom side):...
  • Page 37 7-12 7-12 OK Board Print-layout (Top side): OK Board Print-layout (Bottom side):...
  • Page 38 7-13 7-13 Power Board Print-layout(Bottom side):...
  • Page 39 7-14 7-14 Main Board Print-layout (Top side):...
  • Page 40 7-15 7-15 Main Board Print-layout (Bottom side):...
  • Page 41 DVP3366K/93 Packing View: PAC2 PAC4 PAC1 PAC5 PAC6 PAC7 PAC8 PAC3 PAC11 PAC10 PAC9 PAC9. Display Box PAC6. AV Cable PAC7. Poly Bag PAC1. Accessory Bag PAC11. Left Buffer PAC10. Right Buffer PAC8. Remote Control PAC4. Ueser Manual PAC5. Battery...
  • Page 42 Exploded View for DVP3366K/93: It's a general mechanical exploded view for DVP3366K/93, pls refer to the model set for detailed information. Assy 1 includes components:1.3.4.5.21...
  • Page 43 DVP3366K/93 SERVICE PARTLIST ELECTRICAL PARTLIST ASSY-KU BD COMPONENT PARTLIST 12NC No. Description Q'ty 12NC No. Description Q'ty 996510022415 ASSY-MAIN BD U200 996500032494 IC AS4558M 996510022409 ASSY-PW BD 996510022407 ASSY-KU BD MECHANICAL PARTLIST 996510020957 ASSY-FB BD 12NC No. Description Q'ty 996510020934...
  • Page 44: Revision List

    REVISION LIST Version 1.0 * Initial release for DVP3366K/93...

This manual is also suitable for:

Dvp3366k/93