CrimeStopper RS-900ER Installation Instructions Manual
Series i remote engine starting system
Hide thumbs
Also See for RS-900ER:
- Operating instructions manual (8 pages) ,
- Operating instructions manual (9 pages) ,
- Operating instructions manual (9 pages)
Advertisement
This Remote Start Module provides the following features:
SELECTABLE ENGINE SPEED SENSING:
Tach, Semi-Tachless, & Vacuum
TACH AMPLIFIER:
For dirty or low-level tach signals
PROGRAMMABLE RUN TIME:
10, 20, or 40 minutes
4 ON-BOARD RELAYS:
Main Ignition (IGN1)
IGN2 / Accessory
Starter
Parking Light
REMOTE KEYLESS ENTRY:
Controls power door locks
SECURITY STARTER DISABLE
TIMED SELF-START MODE:
Program vehicle to start every
1-4 Hours
CODE / TACH LEARNING CIRCUITRY
Some of the features listed above are optional connections, and may require additional parts and labor.
This device complies with FCC Rules part 15. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference that may be received, including interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modification could void the user's authority to use the
RS900ER/RS901
REMOTE ENGINE STARTING SYSTEM
INSTALLATION INSTRUCTIONS
TECHNICAL SUPPORT: 1-800-998-6880
Monday - Friday 8:00am - 4:30pm Pacific Time
Web Site: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
SERIES I
TWO PROGRAMMABLE MULTI-
FUNCTION OUTPUTS FOR:
OEM Alarm Disarm
Throttle Pulse for Carbureted vehicles
Starter Disable / Anti-Grind Output
Remote output for trunk pop
Host alarm sensor disable
Defroster Activation
HOOD / BRAKE SAFETY CIRCUITRY
VALET MODE / OVERRIDE
OEM ALARM / KEYLESS ACTIVATION:
Lets a Factory Keyless Entry or Alarm
AUX output activate the Remote Start
DIESEL START COMPATIBILITY
DELAYED REMOTE CONTROL
OPERATION:
Prevents accidental Remote Starts
equipment.
Advertisement
Table of Contents
Related Manuals for CrimeStopper RS-900ER
Summary of Contents for CrimeStopper RS-900ER
-
Page 1: Installation Instructions
SERIES I TECHNICAL SUPPORT: 1-800-998-6880 Monday - Friday 8:00am - 4:30pm Pacific Time Web Site: www.crimestopper.com E-mail: tech-support@crimestopper.com CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 equipment. TWO PROGRAMMABLE MULTI- FUNCTION OUTPUTS FOR: OEM Alarm Disarm... -
Page 2: Wiring Instructions
INSTALLATION CONSIDERATIONS / WARNINGS To ease and reduce installation time, we suggest you consider the following points before starting. 1. Determine most suitable locations for all components to be placed. These components include: the module itself, override / programming switches, and possible relays. 2. - Page 3 PIN 2: ORANGE: MULTI-FUNCTION OUTPUT 2 Output 2 comes pre-programmed to operate as the Anti-Grind/Starter Disable output. It can also be used for the sensor disable circuit for a host alarm. This output activates whenever a remote start is requested, and when the vehicle is remotely locked with the transmitter.
- Page 4 PIN 5: GREEN: (-) START ACTIVATION TRIGGER This wire allows a host alarm (-) Negative Auxiliary Channel Output to activate a Remote Start or it can be connected to a Negative wire of a factory keyless entry system. If the Factory Keyless Entry System wire can produce a Negative output for 1 second or 3 short pulses within 5 seconds, that system could also be used to trigger a remote start.
- Page 5 The TACH LEARNING MODE is the most reliable and consistent method of engine speed sensing. This wire looks for the pulsing signal that is created to monitor the engine speed or fire the coil. Most modern ignition systems utilize a crankshaft sensor to monitor the engine speed. There are 4 different types of signals that may provide adequate signal for TACH SENSE: Type 1 - Will be a computer-controlled ignition.
- Page 6 TACH WIRE TROUBLESHOOTING If all remote start wiring has been completed, attempt a remote start. If engine starts, and starter disengages quickly, and engine continues to run, the tach wire has been properly connected. ** If system does not remote start properly, you will have to locate a different tach wire and reprogram. AN INADEQUATE TACH SOURCE WILL PRESENT ANY VARIETY OF THE FOLLOWING PROBLEMS: Starter stays engaged after engine starts.
-
Page 7: Vacuum Switch
This new feature provides an easy method of starting the vehicle without locating the exact tach wire required. It uses a timed crank output combined with the tach wire as a crude pulse monitor. This combination prevents the starter from engaging into an already running engine and provides a reliable method of detecting when restart is required. -
Page 8: Ignition Switch Wiring
6 PIN HIGH-CURRENT SPADE CONNECTORS: PIN 1: RED 14Ga.: BATTERY CONSTANT FUSED 30A PIN 2: BROWN 14Ga.: STARTER OUTPUT - 30A PIN 3: GRAY 14Ga.: IGNITION 2 - 30A PIN 4: WHITE 18Ga.: + PARKING LIGHTS 10A SEE NEXT PAGE PIN 5: PINK 14Ga.: IGNITION 1 - 30A PIN 6: RED 14Ga.: BATTERY CONSTANT FUSED - 30A See diagram below for connection information:... -
Page 9: Power Door Lock Wiring
POWER DOOR LOCK WIRING 3 PIN DOOR LOCK PLUG: PIN 1: GREEN: Sends a (-) Negative pulse for LOCK; Sends a positive pulse for UNLOCK PIN 2: RED: +12V Coil Power for external relays TERM 86. (If needed.) PIN 3: BLUE: Sends a (-) Negative pulse for UNLOCK;... - Page 10 TESTING FOR REVERSE POLARITY DOOR LOCKS WITH A VOM (5 wire switch) Reverse Polarity Door Lock Systems are a series circuit in which one switch serves as a "master" source for the motor grounds. When any switch in the circuit is pressed, one of the grounds is "lifted" and voltage is applied to the open circuit causing the locks to activate.
- Page 11 POWER DOOR LOCK WIRING DIAGRAMS REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH GROUND/OPEN LOCKING SYSTEM GREEN BLUE DOOR MICRO SWITCH DOOR MICROSWITCH AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN FUSED +12V BLUE ONE WIRE / DUAL VOLTAGE SYSTEM GREEN BLUE FACTORY POWER LOCKING...
- Page 12 CODE LEARNING PROGRAMMING: The RS900ER will learn up to 4 different transmitter security codes. This procedure does not apply to the RS901 add-on Remote Start module. Transmitter Programming: 1) Open Hood(Gray wire grounded). 2) Depress and Hold BRAKE PEDAL, and then Press Program Button until parking lights turn ON solid. 3) Release program button.
- Page 13 Options Programming: 1) Open Hood (Gray wire grounded) Depress and Hold BRAKE PEDAL. 2) Press and Release program button. (Parking lights come on.) 3) Wait 2 seconds, then press and release brake pedal again. 4) Release BRAKE PEDAL 5) Momentarily Press then Release program button the number of times for the option program level desired. Parking lights will flash the same number of times to confirm the program level.