Page 1
802.11ac Outdoor PoE Access Point Customer Project Name: LAP-1, LAP-2 LITE-ON Project Name: WP9331D1-FT24 (LAP, LAP with antenna type I.) WP9331D2-FT24 (LAQ, LAP with antenna type II.) Version: V1.1 This document contains confidential proprietary information and is property of LTC. The contents of this document should not be disclosed to unauthorized persons without the written consent of LTC.
24VDC/48VDC PoE injector which is supplied by customer. There are two SKUs: LAP: Type I antenna - target HPBW 170(H) x 90(V) (LAP-1) LAQ: Type II antenna - target HPBW 120(H) x 30(V) (LAP-2) To protect data during wireless transmission, the device supports WEP data encryption and WPA/WPA2 wireless security to ensure network safely.
Page 3
1x 10/100/1000 Base-TX MDI/MDIX RJ-45 port with PoE PD (to engage with passive PoE injector which is provided by customer.) 1x 10/100/1000 Base-TX MDI/MDIX RJ-45 port Pin definitions : 1/2/3/6 for Data transmission 4/5 for postive power pin Ethernet 7/8 for negative power pin Compliant with following standards: 1.
Page 5
Target type-I antenna HPBW: 170(H) x 90 (V) (Simulated results: HPBW: 185(H) x 90(V) @2.4GHz, HPBW: 178(H) x 71(V) @5GHz) Target type-II antenna HPBW: 120(H) x 30 (V) (Simulated results: HPBW: 115(H) x 50(V) @2.4GHz, HPBW: 115(H) x 50(V) @5GHz) Peak Gain: >...
Page 6
(The simulated results at 5GHz band are HPBW 115 x 50 degrees 8.0dBi. The final results depend on the test reaults on EVT/DVT samples.) Power Supply LAP, LAQ should be powered by 24VDC POE Injector (PoE injector is supplied by ...
Page 7
S/W Features Software specification Feature Item Feature Detailed Description Wireless Wireless mode 11b/g/n 11a/n/ac Operation mode Access point mode (Support both normal station and WDS station) Bandwidth 20MHz 20/40MHz dynamic 20/40/80MHz dynamic Aggregation in 11n mode A-MPDU SSID Support 4 virtual AP EDCA WMM QoS-DSCP configurable via web UI Other parameter configurable...
Page 9
( details refer to ME drawing mounting kit code: PW-5-N, separately) LAP, LAQ With extra mounting brackets and the screws, can be mounted on pole with the ability of being 90D to the ground. The mount kit can support Φ60 ~ Φ140mm pole diameter.
Page 10
ME drawing mounting kit code: PW-4-N, separately): LAP, LAQ With two extra mounting brackets and the screws, can be mounted on pole with the ability of tilt up from 0 to 60 degrees and tilt down from 0 to 50 degrees.
One screw kit for wall mounting & poll mounting (3.1.2 a & b) 5 Certification Requirements STATUATORY (Standard) USA FCC (Non DFS) ESD protection: 4KV (prestest at LITEON lab by following IEC61000-4-5 standard) Note: Primary covered the certificates of FCC for Non-DFS bands; multiple countries certificate to be quoted separately...
Page 12
Surge protection: 4KV (Prestest at LITEON or 3rd party lab by following IEC61000-4-5 standard) Others RoHS (self- announcement) WEEE (self- announcement)
Page 13
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.