Related Manuals for Clarion Ungo Pro Security SR9000
Summary of Contents for Clarion Ungo Pro Security SR9000
- Page 1 M M o o d d e e l l S S R R 9 9 0 0 0 0 0 0 ➤ O O w w n n e e r r ’ ’ s s G G u u i i d d e e...
-
Page 2: L L I I M M I I T T E E D D L L I I F F E E T T I I M M E E C C O O N N S S U U M M E E R R W W A A R R R R A A N N T T Y Y
Warranty shall be limited to the repair or replacement of the product, at the sole discre- tion of Clarion. If it becomes necessary to send the product or any defective part to Clarion, the product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. - Page 3 ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. Should you have any difficulties with the performance of this product during warranty, please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer. You may also contact the National Service Manager at the following address below for additional service help you may need.
-
Page 4: Table Of Contents
t t a a b b l l e e o o f f c c o o n n t t e e n n t t s s l l i i m m i i t t e e d d l l i i f f e e t t i i m m e e c c o o n n s s u u m m e e r r w w a a r r r r a a n n t t y y ................. . i i s s t t a a n n d d a a r r d d t t r r a a n n s s m m i i t t t t e e r r c c o o n n f f i i g g u u r r a a t t i i o o n n . - Page 5 arming diagnostics ..........35 disarming diagnostics .
- Page 6 s s t t a a n n d d a a r r d d t t r r a a n n s s m m i i t t t t e e r r c c o o n n f f i i g g u u r r a a t t i i o o n n controls the A A r r m m and P P a a n n i i c c On/Off function.
- Page 7 By carefully reading this Owner's Guide prior to using your system, you will maximize the use of this system and its features. You can print additional or replacement copies of this manual by accessing our web site at www.clarion.com. two-stage shock sensor ®...
-
Page 8: Fcc/Id Notice
➜ fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. -
Page 9: Caution
➜ caution This product is designed for fuel injected, automatic transmis- sion vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use. © 2007 directed electronics... - Page 10 r r e e m m o o t t e e c c o o n n t t r r o o l l d d i i a a g g r r a a m m note:The Program button is located on the back of the remote.
- Page 11 s s t t a a n n d d a a r r d d r r e e m m o o t t e e c c o o n n f f i i g g u u r r a a t t i i o o n n 1.
- Page 12 s s y y s s t t e e m m m m a a i i n n t t e e n n a a n n c c e e This system needs no specific maintenance beyond remote control battery replacement.
-
Page 13: Standard Configuration
t t r r a a n n s s m m i i t t t t e e r r f f u u n n c c t t i i o o n n s s The receiver uses a computer-based Learn Routine to learn the transmitter buttons. -
Page 14: Standard Icon Configurations
Button The remote start feature is turned On/Off by pressing this button twice. Buttons The remote start timer mode function of the system is controlled by pressing these buttons simultaneously. Buttons The Turbo/Short Run feature is controlled by these buttons (refer to the Turbo/Short Run section for additional details). - Page 15 Icon The receive icon will be displayed while the remote control is receiving a page from the vehicle. Icon The signal icon will be displayed if a command is transmitted to the vehicle but a command page is not received. Icon The armed status icon will be displayed when the system is locked and armed.
- Page 16 Icon The siren icon will be displayed as an indicator that the siren is sounding. Icon The alarm icon will be displayed if the system has been violated, and will continue to be displayed until the siren cycle is complete. Icon The vibrate icon will be displayed when the Vibrate Mode is on.
- Page 17 The Sensor 2 icon will be displayed if an additional Dual-Stage sensor has been triggered as a full-triggered or Warn Away Icon The hammer icon will flash when either Sensor 1 or 2 has been triggered as either a Warn Away Icon The ignition icon will be displayed to indicate that the ignition is on when arming the system (Bypass Notification) or turned on...
-
Page 18: System Signal Paging Features
r r e e m m o o t t e e o o p p e e r r a a t t i i o o n n a a n n d d p p r r o o g g r r a a m m - - m m i i n n g g i i n n s s t t r r u u c c t t i i o o n n s s This combination two-way remote start alarm system utilizes Secure Digital Communication (SDC) for remote operation of your vehicle... - Page 19 Alarm Page If the alarm system is triggered while armed, an Alarm Page will be sent to the remote control. After receipt of an Alarm Page, the LCD icons will display the alarm system status information and the remote control will generate Alarm Page alerts. An Alarm Page alert is a single beep or vibration from the remote control every 60 seconds to alert the user that the alarm system was triggered and will continue until the alarm page is cleared.
-
Page 20: Programmable Remote Control Features
➜ programmable remote control features To enter programming mode Press the Program button on the back of the remote or hold the four remote control buttons on the front of the remote simultane- ously until one long beep is heard. Programming Mode has now been entered. -
Page 21: Warning! Safety First
Illumination On/Off Within five seconds of entering Programming Mode, press The remote will beep once for on, twice for off and the light will turn on/off with each press. Page Mode On/Off After entering Programming Mode, press seconds to toggle on and off. When the Page Mode is on, the remote control will wake up periodically to check for messages from the security module. - Page 22 partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle.
- Page 23 ➤ After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed.
-
Page 24: Active Arming
➜ active arming You can arm the system by pressing one second. When the system arms, you will hear a short siren sound, or chirp, and see the parking lights flash once. If the power door locks are controlled by the system, the doors will also lock. While the system is armed, the status LED will flash approximately once per second, indicating that the system is actively protecting your vehicle. - Page 25 note: If any protected entry point (such as a door or a switch-protected trunk or hood) is open, the system will not passively arm (unless forced passive arming is pro- grammed on. See Programming Options section.) Addi- tionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over.
-
Page 26: Multi-Level Security Arming
➜ multi-level security arming Multi-Level Security Arming allows you to select which of the system's inputs or sensors will be active and which will be bypassed when the system is armed. (See Table of Zones section of this guide.) Pressing within five seconds of arming the system will activate the Multi- Level Security feature. -
Page 27: Arming While Driving
➜ arming while driving Your security system can be armed while driving the vehicle! Simply press vehicle is running. The siren will chirp once to indicate that the security system is armed, and then once more to indicate that the ignition is on. -
Page 28: Disarming Without A Transmitter
system will not disarm, but rather reset. This prevents you from disabling the system should you wish to disarm it without visu- ally checking the vehicle. Pressing will disarm the system; pressing this button during the first six seconds of the triggered sequence will disarm the security system immediately. -
Page 29: Silent Mode
Number of Presses_____________________________________ important! The Valet button can be programmed to respond to 1-5 presses for the disarm function. You must check with the installer to verify the programming for your individual unit. ➜ silent mode To temporarily turn off the arm or disarm chirps, use Silent Mode™. -
Page 30: Valet Mode
➜ valet mode You can prevent your security system from automatically arming and triggering by using Valet washing the vehicle or having it serviced. In Valet security system will not arm, even with the remote transmitter, but all convenience functions (door locks, trunk release, etc.) will continue to work normally. - Page 31 up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle.
-
Page 32: Valet Take-Over
When you are ready to drive the vehicle: 1. Insert the ignition key and turn it to the ON (not the START) position. 2. Press the brake pedal. note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. -
Page 33: Short-Run/Turbo
® To perform Valet Take-Over: 1. Before turning off the engine, press and release transmitter twice within 3 seconds. Then wait five seconds. 2. Turn the ignition key to the OFF position. (The engine will stay running.) 3. The engine will run until the pre-programmed time elapses or a shut-down input is received. -
Page 34: Timer Mode
Turn off the key, the engine will keep running. Exit and secure the vehicle. The engine will turn off after the programmed run time. ➜ timer mode By pressing the remote lights will flash 4 times and then start the vehicle and run for the set duration. -
Page 35: Starter Anti-Grind Circuitry
Timer Mode should be used only in important! ! open areas. Never start and run the vehicle in an enclosed space such as a garage or carport. To exit timer mode, turn the ignition switch on any time the engine is running. The parking lights will flash 4 times, indicat- ing timer mode has been exited. -
Page 36: Disabling The Remote Start System
➜ disabling the remote start system This feature allows your system's remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the shutdown toggle switch to the OFF position. -
Page 37: Nuisance Prevention Circuitry
pedal will shut down the motor at any time during remote start operation, as well as preventing the remote start from activating while it is being pressed. ➜ nuisance prevention circuitry Your system has Ungo’s Nuisance Prevention Circuitry (NPC ). It prevents annoying repetitive trigger sequences due to ™... -
Page 38: Arming Diagnostics
note: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the igni- tion. If testing your system, it is important to remember that the NPC bypassed and appear to stop working. -
Page 39: Disarming Diagnostics
delay and you arm your security system before the interior light turns off, you may hear a second Bypass Notification chirp. Once the light turns off, however, the security system resumes normal monitoring. note: Bypass Notification does not occur when the sys- tem is in Silent Mode or if the notification chirps have been programmed off by the installer. -
Page 40: System Status Chirps
➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below. Action Number of Chirps 1 (3-second delay), 1 Disarm Disarm Disarm ➜ table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input. -
Page 41: Interpreting Zone Diagnostics
sensors Ignition trigger ➜ interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the LED. Active or triggered zones will be indicated by a pattern of blinks by the LED. - Page 42 even if you use the remote control out of range of the vehicle. However, if the remote has been pressed many times out of range of the vehicle, or the battery has been removed, it may fall out of sync with the control unit and fail to operate the system. To re- sync the remote simply press the vehicle.
- Page 43 note: Owner Recognition cannot be programmed with- out an Ungo ProSecurity Programmer and the necessary software. Check with your dealer for more information. r r a a p p i i d d r r e e s s u u m m e e l l o o g g i i c c This Ungo system will store its current state to non-volatile memory.
-
Page 44: To Enter Programming Mode
Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a one hour period while the system is in Valet system remains in Valet the next time the ignition is turned on and then back off. p p r r o o g g r r a a m m m m i i n n g g r r e e m m o o t t e e c c o o n n t t r r o o l l f f e e a a t t u u r r e e s s ➜... -
Page 45: Sensor Icon Selection (Hood/Trunk)
➜ Sensor icon selection (hood/trunk) to toggle display selections between hood only (1 beep), trunk only (2 beeps), or hood and trunk (3 beeps) on the LCD display. The installer will have set the remote up to correctly display the installation (hood pin only, trunk pin only, or hood and trunk pin installed). - Page 46 ➤ A A c c t t i i v v e e arming (transmitter only) or passive arming (auto- matic arming 30 seconds after the last door has been closed). ➤ Arming/disarming siren chirps o o n n or off. ➤...
- Page 47 note: When the system passively arms after one hour, the entry point that has been left open, and anything con- nected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational. ➤...
- Page 48 note: This feature will only function if the FailSafe Starter Kill relay has been installed. ➤ Siren tones and chirp volume. The output of the Revenger Soft Chirp siren consists of six different tones in sequence. ™ Any of these tones can be eliminated by a dealer, resulting in a unique, easily identifiable siren sound.
- Page 49 The 520T keeps the system armed, triggers Backup Battery: the alarm and keeps the starter interrupt active if main battery is disconnected. Prevents the vehicle’s hood from being opened Hood Lock: without a key, keeping thieves away from the system’s siren, the battery connections, and other components under the hood.
- Page 50 g g l l o o s s s s a a r r y y o o f f t t e e r r m m s s The “brain” of your system. Usually hidden under- Control Unit: neath the dash area of the vehicle.
- Page 51 alarm “goes off ” or “trips.” The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration. A small push button mounted at a discretionary Valet Switch: location inside the vehicle. It is used to override the starter inter- rupt when a transmitter is lost or damaged, or to enter or exit Valet Mode.
-
Page 52: Quick Reference Guide
Quick Reference Guide Arming ■ To arm, press the parking lights will flash once. Arming while driving ■ To arm the system while driving, press vehicle is running. The system will chirp once and then once more to indi- cate that the ignition is on. Disarming ■... - Page 53 Get Started Get Protected Ungo Pro Security 6200 Gateway Drive Cypress, CA 90630 800-GO-CLARION © 2007 Directed Electronics - All rights reserved GSR9000 01-07...