ADTRAN XFP Quick Start

Quick Start
D
ESCRIPTION
The 10 Gig XGS-PON Optical Line Termination (OLT) Class N2 Small Form-factor
Pluggable (XFP) is a single-mode fiber XFP. It plugs into an ADTRAN optical
interface that is designed to accept XFPs. The XFP provides a single optical
interface to a physical interface, and is intended for use with a 9.953 Gbps
Passive Optical Network (PON) OLT module. The XFP provides a 9.953 Gbps
XGS-PON interface to the supporting system when installed into an appropriate
module.
The XFP is configured with an L-band 9.953 Gbps downstream transmitter and a
C-band 9.953 Gbps upstream receiver, which work in a TDM configuration. The
XFP is designed to support up to 32 subscribers over distances of up to 20 Km in
the Optical Distribution Network (ODN). It is FDA 21CFR1040.10 and IEC
60825-1 Class I laser safety compliant and meets EU RoHS Directive.
This XFP supports the following features:
■
ODN Class N2 Transceiver
■ Data rate: 9.953 Gbps
■
Optical Receive Wavelength: 1270 – 1280 nm
■ Optical Transmit Wavelength: 1577 –1580 nm
■ Optical distance: 20 Km maximum
■ Hot Pluggable
Applications:
■
XGS-PON Access networks
■ Fiber to the Home (FTTP)
■ Fiber to the Building (FTTB)
■ Fiber to the Curb (FTTC)
Due to compliance certification requirements, use only XFPs supplied by
ADTRAN. ADTRAN cannot certify system integrity with other XFPs.
I
NSTALLATION
Before installing the equipment, inspect the XFP. If damage has occurred during
shipping, file a claim with the carrier, and then contact ADTRAN Customer
Support. For more information, refer to the warranty.
Installation Steps
To install the XFP into an appropriate device, complete the following steps:
g
NOTE
Do not remove the protective end cap from the XFP until the fiber optic cable is
ready to be connected.
1. Insert the XFP into the XFP cage on the module. Ensuring that the latch on
the XFP is facing upward, slide the XFP all the way into the XFP cage until
there is an audible "click".
g
NOTE
The latch on the XFP is for removal only. When removing the XFP, rotate the latch
away from the XFP. It should easily slide out of the cage.
w
NOTICE
Do not remove the protective end cap until the optical fiber connection is made.
Ensure that you keep the protective end cap on whenever the transceiver optical
fiber connector is not inserted.
2. Continue the installation and turn-up of the host module using the
instructions in the Job Aid or Quick Start provided with the module or other
system-level documentation available online at www.adtran.com.
ADTRAN Pluggable Optics
XFP
10 Gig XGS-PON N2 OLT
S
PECIFICATIONS
Specifications for this XFP are as follows:
■ General
♦
♦
♦
♦
♦
■ Optical
♦
♦
■
Environmental
S
AFETY AND
E
NGLISH
f
Read all warnings and cautions before installing or servicing this equipment.
C
This product is a Class 1 Laser module that complies with FDA 21 CFR 1040.10
and 1040.11 and IEC 60825-1. This product is NRTL Listed and CB Certified to all
applicable American and European safety standards. For continued compliance
with the above standards, install only ADTRAN-approved Class 1 Laser Modules
in ADTRAN products.
Module Type: XFP
Media Type: Fiber
● Single-Mode
●
BIDI
Signal Data Rate:
●
Maximum: 9.953 Gbps
Distance: 20 Km
Compatible with XFP MSA
Transmitter
●
Laser Diode Type: DFB
● Transmit Wavelength: 1577 nm
●
Tx Power: +4.0 dBm to +8.0 dBm
● Spectral Width: 1 nm
● SMSR: 30 dBm
● Extinction Ratio: 8.2 dB
● Dispersion Penalty: 1 dB
Receiver
● Type: APD
● Central Wavelength: 1270 nm
● Receiver Sensitivity: –28 dBm
● Receiver Overload: –7 dBm
●
Operational Temperature Range: –5°C to +55°C
● Operational Case Temperature Range: 0°C to +70°C
● Storage Temperature Range: –40°C to +85°C
● Relative Humidity 5% to 85%
R
EGULATORY
WARNING!
CAUTION!
May 2019
61442548F2C-13B
P/N: 1442548F2C