Related Manuals for Saturn 20HS1500-BK-SV
Summary of Contents for Saturn 20HS1500-BK-SV
- Page 1 SATURN 20HS1500-BK-SV 20HS2000-BK-SV HIGH SPEED FLOOR MACHINE OWNER’S/OPERATOR’S MANUAL 2-25-19 WWW.EDIC-USA.COM...
-
Page 2: Table Of Contents
TABLE OF CONTENTS RECEIVING YOUR EQUIPMENT................... WARNINGS AND SAFETY....................ELECTRICAL INFORMATION..................GROUNDING INSTRUCTIONS..................MAINTENANCE......................... CORD SAFETY AND STORAGE..................CLEANUP AND STORAGE..................... MAINTENANCE, CLEANUP, STORAGE..............PAD INSTALLATION......................DRIVE BELT ADJUSTMENTS..................MACHINE OPERATION....................MANEUVERING THE MACHINE................SERVICING......................... FINAL ASSEMBLY PROCEDURE.................. 8-15 EXPLODED VIEW: BOTH MODELS................16-17 1500 RPM MODEL PARTS LIST.................. -
Page 3: Receiving Your Equipment
FAILURE TO COMPLY WITH THE FOL- When your package is delivered, check all cartons care- LOWING WARNINGS AND INSTRUCTIONS fully for signs of rough handling. If your SATURN is WILL VOID THE WARRANTY. damaged, notify the carrier immediately and request an inspection. -
Page 4: Electrical Information
GROUNDING INSTRUCTIONS: • Connect to a properly grounded outlet only. See “Grounding Instructions. ” This piece of equipment must be grounded. Should an • Turn off all controls before unplugging. electrical malfunction occur, grounding provides a path • When using an extension cord, use a 3 conductor of least resistance for electrical current- reducing the risk grounding cord, 12 gauge wire or heavier. -
Page 5: Maintenance
Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run this SATURN over the WARNING: Do not store the machine with the drive cord. -
Page 6: Drive Belt Adjustments
WARNING: DO NOT OVER-TIGHTEN THE BELT. ALWAYS TIGHTEN OR LOOSEN IN SMALL INCRE- MENTS. SERVICING: In the event that your SATURN requires service, please contact EDIC: 800-338-3342 2. Locate the two belt tensioner s at the rear of the ma-... -
Page 7: Machine Operation
MACHINE ON/OFF OPERATION: TO MANEUVER THE MACHINE: This equipment is equipped with a safety “LOCK OUT” lever. Refer to Diagram 1 for steps 5, 6, and 7. CAUTION: THIS MACHINE CANNOT BE OPERATED WITH 1. Install the pad driver and pad or attachment. THE HANDLE IN THE UPRIGHT POSITION. -
Page 16: Exploded View: Both Models
20HS1500-BK-SV & 20HS2000-BK-SV FLOOR MACHINE BASE ASSEMBLY EXPLODED VIEW 44 93 1/17/2019 REV 04... - Page 17 20HS1500-BK-SV & 20HS2000-BK-SV FLOOR MACHINE HANDLE ASSEMBLY EXPLODED VIEW 9 10 1/17/2019 REV 04...
-
Page 18: 1500 Rpm Model Parts List
HS1500-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. 2400BR PAD HOLDER, HIGH SPEED, 20" B00177 TERMINAL LUG, QD F 16-14AWG, F.INS B00180-10-3 RING TERMINAL, 16-14AWG, P.INS B00187 CABLE CLAMP, NYLON .43 B02196-1 INDICATOR LIGHT B10734 STRAIN RELIEF, HANDLE B11465 SWITCH, DPST PUSH BUTTON B11465-NUT... - Page 19 HS1500-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. C11558 LOCKNUT, 3/8-16 C11559-1 WASHER, 1/2 C11567 SET SCREW C11568-1 HEX BOLT, 5/16 X 2.5, SS C11569-1 SCREW, 3/8 X 1.25, HH, SS C11571-1 SCREW, 3/8 X 3/4, HH, SS C11574 RETAINING RING C13100...
- Page 20 HS1500-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. G11531 BEARING G11557 MOTOR, HIGH SPEED G11943 WHEEL, 5" H00565-5 LABEL, SERIAL #, STANDARD H02548-2 LABEL, CORD H03545 COVER, SERIAL # LABEL H11493 SAFETY LABEL H11831 EDIC LABEL H12070 LABEL, 1500RPM K00662-500...
-
Page 21: 2000 Rpm Model Parts List
HS2000-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. 2400BR PAD HOLDER, HIGH SPEED, 20" B00177 TERMINAL LUG, QD F 16-14AWG, F.INS B00180-10-3 RING TERMINAL, 16-14AWG, P.INS B00187 CABLE CLAMP, NYLON .43 B02196-1 INDICATOR LIGHT B10734 STRAIN RELIEF, HANDLE B11465 SWITCH, DPST PUSH BUTTON B11465-NUT... - Page 22 HS2000-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. C11558 LOCKNUT, 3/8-16 C11559-1 WASHER, 1/2 C11567 SET SCREW C11568-1 HEX BOLT, 5/16 X 2.5, SS C11569-1 SCREW, 3/8 X 1.25, HH, SS C11571-1 SCREW, 3/8 X 3/4, HH, SS C11574 RETAINING RING C13100...
- Page 23 HS2000-BK-SV HS FLOOR MACHINE PARTS LIST ITEM NO. PART NUMBER DESCRIPTION QTY. G11531 BEARING G11557 MOTOR, HIGH SPEED G11943 WHEEL, 5" H00565-5 LABEL, SERIAL #, STANDARD H02548-2 LABEL, CORD H03545 COVER, SERIAL # LABEL H11493 SAFETY LABEL H11831 EDIC LABEL H12069 LABEL, 2000RPM K00662-500...