Chamberlain TriCode TC4 User Manual page 2

Table 1: Transmitter
Button Outputs vs.
Configuration Inputs
D = Linear/Delta-3 TM
M = Multi-Code TM
TM
S = Stanley
1 = Code switch 1
2 = Code switch 2.
1 Configuration switch 1 and dip switch 1 are on the top.
2 Configuration switch 2 and dip switch 2 are on the bottom.
3 Transmitter button output is given in the format RECEIVER TYPE/CODE SWITCH USED.
Step 4 Recode Receiver Codes
Once the transmitter codes have been set, verify the receiver codes are set to the following settings:
T M
Linear/Delta-3 Receiver Type Detail
When the TC4 is set to the Linear/Delta-3
Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1.
Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from Button 2.
Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from Button 3.
Receiver 4 - Set switch 1 OFF, switch 2 ON, match switches 3-8 on switch 2, activates from Button 4.
T M
Multi-Code Receiver Type Detail
When the TC4 is set to the Multi-Code
Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.
Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.
Receiver 3 - Set switch 10 OFF, match switches 1-9 on switch 2, activates from Button 3.
Receiver 4 - Set switch 10 ON, match switches 1-9 on switch 2, activates from Button 4.
TM
Stanley Radio Receiver Type Detail
When the TC4 is set to the Stanley
Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.
Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.
Receiver 3 - Set switch 10 OFF, match switches 1-9 on switch 2, activates from Button 3.
Receiver 4 - Set switch 10 ON, match switches 1-9 on code switch 2, activates from Button 4.
NOTE: The DIP switches in the receiver must match the DIP switches in all transmitters used to operate the receiver.
Step 5 Test the Equipment
If not already installed, connect the receivers to the
operators as described in their installation instructions.
Be sure the door/gate area is clear of people and
obstructions. Activate each transmitter button and
verify that each receiver triggers its operator.
Battery Replacement
The 9 volt battery should last 12 to 18 months of normal
use. The green LED on the face of the transmitter will
light dimly or not at all when the battery needs replacing.
The battery is located under the access cover.
HOW TO ORDER REPAIR PARTS
INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE
6 DAYS A WEEK CALL OUR TOLL FREE NUMBER
1-800-528-3536
HOURS 7:00 TO 3:30 p.m. (Mountain Std. Time)
MONDAY Through SATURDAY
OR CONTACT US THROUGH THE WEB AT
WWW. CHAMBERLAINGROUP.COM
01-16701C
Configuration Switch 1 1
Delta-3 Multi Stanley
1
0 0
1 0 0
1
0 0
0 1 0
0
1 0
0
1 0
0
0 1
0
0 1
0 0 1
T M
transmitter type, set the receiver DIP switches as follows.
T M
transmitter type, set the receiver DIP switches as follows.
T M
radio transmitter type, set the DIP switches as follows.
© 2000, The Chamberlain Group, Inc.
All Rights Reserved
Configuration Switch 2 2
Delta-3 Multi Stanley
1 0 0
0 1 0
0 0 1
1 0 0
0 1 0
0 0 1
1 0 0
0 1 0
0 0 1
FIGURE 3
DIP Switch 1
DIP Switch 2
Battery 9V
Sliding Cover
Transmitter Button Output
1 2 3 4
D/1 D/2 D/2 D/2
D/1 M/1 M/2 M/2
D/1 S/1 S/2 S/2
M/1 M/1 D/2 D/2
M/1 M/1 M/2 M/2
M/1 M/1 S/2 S/2
S/1 S/1 D/2 D/2
S/1 S/1 M/2 M/2
S/1 S/1 S/2 S/2
Configuration
Switch 1
Configuration
Switch 2
3